Argos RONDA 8 SEATER CORNER DINING SET 7473441 User manual

Issue 1 - 28/09/17
Assembly Instructions - Please keep for future reference
Width -164cm
Depth -71cm
Height -76cm
Dimensions
RONDA 8 SEATER CORNER DINING SET
7473441
Important - Read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 03456400800
For further assistance please visit http://www.argos-support.co.uk/

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
1
Care and maintenance
!
• Check you have all the
components and tools listed on
page 2 & 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the components during assembly,
this could cause damage.
• Assembly on a soft level surface
to avoid damaging the unit or your
floor.
• Parts of the assembly will be
easier with 2 people.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Dispose of all packaging carefully
and responsibly.
•Do not stand on this bench.
•Warning: The unit weighs
approximately 13.3 kgs. Please lift
with care.
• Wash frame parts with mild
soap and water, rinse thoroughly,
and dry completely. Do not use
bleach, acid, or other solvents
on the frame parts.
• We recommend the use of
furniture covers when not in use.
• Inspect and tighten all bolts
and fasteners on a regular basis
to ensure the proper performance
and safety of your bench.
• In order to prolong the life and
beauty of your bench, we
recommend that it be stored in a
dry and protected area when not
in use .

Note: The quantities below are the correct amount to complete the assembly.
10mm Hex Key
Ruler - Use this ruler to help correctly identify the screws
Tools required
Components - Fittings
Please check you have all the fittings listed below
2
4mm Hex Key
15
M6 x 70mm Bolt x 4 M6 x 35mm Bolt x 1 M6 x 15mm Bolt x 4
AB C
D10 Spring Washer x 9
D

Seat Assembly x 1Back Assembly x 1
12
Left Arm x 1
3
Back Cushion x 3
5Seat Cushion x 3 6
Right Leg x 1
4
Components - Parts
Please check you have all the parts listed below
3

4
Step 1
Assembly Instructions
Step 2
At the rear of the seat, fix the
seat assembly to the back
assembly by using bolts ,
spring washers . Keep the
bolts loose.
Place the back assembly
onto a non-abrasive surface,
such as a carpet. Insert the seat
assembly into the back
assembly .
2
1
A
D
A
D
1
2
1
1
2
2
1
2
1

Step 3
Assembly Instructions
Step 4
4
1
Fix the right leg to the back
assembly by using bolts ,
spring washers . Keep the
bolts loose.
Note:
The labels marked “L” and “R”
on left arm (#3) and right leg
(#4) should coincide with Figure
to ensure proper assembly.
At the front of the seat, insert the
left arm and right leg into
the seat assembly by using
bolts , spring washers .
Keep the bolts loose.
D
C
1
4
4
2
2
3
C
C
C
D
C
D
D
D
5
3 4
2
4
R
L

Step 5
Assembly Instructions
Step 6
56 Place the cushions and
onto the bench. Secure the
cushions to the bench by using
the velcro straps.
Assembly is completed.
If you need help or have damaged or missing parts, call the Customer Helpline: 03456400800
For further assistance please visit http://www.argos-support.co.uk/
Retailer: Argos
Address: 489-499 Avebury Boulevard Saxon Gate West, Central Milton Keynes Bucks, MK9, 2NW
3
1
Fix the left arm to the back
assembly by using bolts ,
spring washers . Make sure
that all of the bolts have been
tightened completely.
B
D
3
1
BD
5
55
6
6
6
6