Argos 603/4135 User manual

Vendor Name: TORCH 2100 CO., LTD.
Product Name: WOW SWANLEY OAK 150 TABLE
Code: 3070051, 3070037
Date: 7/7/2014
Instruction Manual 1 of 6
Inst ruc t ion Manual
Insert Additional Pages If Required.
Document No.: D114 Issue: 011 Approved: MP/DA Page 19 of 34

Vendor Name: TORCH 2100 CO., LTD.
Product Name: WOW SWANLEY OAK 150 TABLE
Code: 3070051, 3070037
Date: 7/7/2014
Instruction Manual 2 of 6
Inst ruc t ion Manual
Insert Additional Pages If Required.
Document No.: D114 Issue: 011 Approved: MP/DA Page 20 of 34

Dining Chair
Assembly Instructions - Please keep for future reference 603/4135
603/2333
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 08/09/13
Dimensions
Width - 44cm
Depth - 54cm
Height - 92cm
603/2900
133/6948
602/9834
603/2364

1
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warnings
Care and maintenance
• Assemble this product on a flat
surface.
• Assemble all parts loosely
before tightening any bolts.
• Do not discard any of the
packaging until you have
checked that you have all the
parts and the pack of fittings.
• Discard all extra fittings and
keep fittings out of reach of
children.
• Unit weight: 4.9kgs.
• Maximum safe weight of user:
110kgs.
• Retain Assembly Instructions
for future reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• This product should only be
used on firm, level ground.
• Make sure the legs remain in
contact with the ground.
• Do not stand on the product.
• Please clean the product using
either damp (not wet) cloth and
a mild domestic soap solution or
by using an appropriate polish.
• Do not use any abrasive
materials when cleaning.
• From time to time check that
there are no loose bolts on this
unit.

2
Components - Parts
Components - Fittings
Please check you have all the parts listed below
Please check you have all the fittings listed below
Backrest
(36 x 10 x 92cm)
M6 x 50mm Bolt x 9
If you have damaged or missing components,
call the Customer Helpline: 08456 400800
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
1Seat
(43.5 x 41 x 9.5cm)
2Leg x 2
(3 x 3 x 43cm)
3
A
Ruler - Use this ruler to help correctly identify the screws
0 15 30 45 60 75 905 20 35 50 65 80 9510 25 40 55 70 85 100 120 140105 125 145110 130 150115 135 155 160 165 170
Flat washer x 9
C
Spring washer x 9
B
Allen key x 1
D

3
Place the backrest on a
flat protected surface.
Position the seat on
the backrest as
shown and fix using bolts
, spring washers
and washers .
Important:
Fasten bolts
using allen key
but do not fully
tighten at this
stage.
Note:
Use oval head of
allen key on
tight angles.
Assembly Instructions
Step 1
Step 2
1
2
2
3
3
3
A
D
D
A
A
A
A
A
C
B
C
B
C
B
C
CB
A CB
C
B
B
Attaching backrest
2
1
A
C
B
A
C
B
A
B
C
A
C
B
A
C
B
A
C
B
A
C
B
2
1
A
C
B
Attaching legs
Place the seat upside
down on a flat protected
surface.
Insert the legs into the
holes of the seat as
shown and fix using bolts
, spring washers
and washers .
Important:
Fasten bolts
using allen key
but do not fully
tighten at this
stage.
Note:
Use oval head of
allen key on
tight angles.
2
3
A
D
D
B
C
2

4
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
D
D
Assembly Instructions
Aligning & securing the
legs
Carefully turn the chair
upright and place on a
flat surface.
a: Tighten all bolts using
allen key .
Note:
Use oval head of allen
key on tight angles.
Note: This step is
essential to prevent the
chair from wobbling due
to uneven legs.
b: Carefully sit on the
chair and make
adjustments to ensure
the legs are flat even on
the floor.
c: After the sitting test,
re-tighten bolts again if
any adjustment is
needed.
Note: It is highly
recommended to
re-tighten all bolts after
using the chair for 7
days.
Note: Keep allen key to
re-tighten bolts when
required.
D
D
Assembly is complete.
Step 3
a:
b:
c: