Argos Metal Highsleeper Wardrobe 151/5680 User manual

Assembly Instructions Please keep for future reference 151/5680
183/5030
Dimensions
Width - 185cm
Depth - 50.5cm
Height - 138cm
Metal Highsleeper Wardrobe
-
Version 3 Date: 16/04/14
Important
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
- Please read these instructions fully before starting assembly

Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Safety and Care Advice
Important –Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
Glue safety - Take care when using glue, please follow the advice below
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts.
• Regularly check and ensure
that all bolts and fittings are
tightend properly.
Handy Hints
• Do not use this item if any
components are missing or
damaged.
• Parts of the assembly will be
easier with 2 people.
• Argos Ltd. MK9 2 NW. • This product is intended for
children in the age 6 or above.
• Maximum load: 50 kgs.
• Assembly of this product must
be carried out by a competent
adult.
IMPORTANT: RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
• During assembly children
should be kept away from the
product due to possible risk of
injury.

2
Components - Panels
Please check you have all the panels listed below
Table top (105 x 48cm)
1
Back panel (101.8 x 25cm)
2
Top panel (105 x 19.7cm)
3
Shelf (101.8 x 19.6cm)
4
Top right panel (60 x 19.6cm)
5
Top left panel (60 x 19.6cm)
6
Top support x 2
(101.8 x 4.2cm)
7
Left side panel (75 x 47.9cm)
9
Right side panel (75 x 47.9cm)
10
Below panels are for desk
Back support (101.8 x 30cm)
8
If you have damaged or missing components, call the
Customer Helpline:
Argos = 0345 6400800

3
Right side panel (136.5 x 48.2cm)
11
Left side panel (136.5 x 48.2cm)
12
Middle panel (119 x 48.2cm)
13
Door panel (120 x 40.2cm)
14
Back panel x 2 (121.7 x 39.8cm)
15
Top panel (80 x 50cm)
16
Bottom panel (76.8 x 48.2cm)
17
Shelf x 2 (47.5 x 37.5cm)
18
Front panel (76.8 x 15.9cm)
19
Pilot holes for guidance only
Pilot holes for guidance only
Finished front edge
Below panels are for wardrobe
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline:
Argos = 0345 6400800

14mm Screw x 2
Handle x 1
4
Note: The quantities below are the correct amount to complete the assembly. in some cases mor
may be supplied than are required.
Components - Fittings
ABC
39mm Locking pin x 6
DEF
15mm Locking nut x 6
GHI
JKL
MNO
50mm Dowel x 4
15mm Screw x 16
30mm Dowel x 29
Door hinge x 2
30mm Screw x 1
P
Wall plug x 2
Q
50mm Screw x 46
Clothes rail x 1 Shelf support x 8
(12 screws are included
in the door hinge bag)
Wall strap x 2
Rail support x 2
Glue x 1
Nail x 34
(This screw is
included in the
wall strap bag)
x 2 Door pad x 2
R
Ruler - Use this ruler to help correctly identify the screws
Tools required
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Small
hammer
Ruler/tape
measure
Drill
Eye protection
(when using a
hammer or glue)
7mm Suitable drill bit
(for use with wall plug)
The screws length is measured from the head to the point (30mm screw shown).

5
Assembly Instructions (Desk)
Step 1
a:
b:
3
4
4
5
6
7
7
Attaching top unit
7
a:
the Top panel
onto the
Top
support .
C
7
4
b:
onto the the Shelf
support .
C
left panels & onto
the Shelf and Top
support .
C
3
c:
56
4
7
c:
Continued on next page.
Finished
front edge
Finished
front edge
Finished
front edge
Finished
front edge
Groove underneath
Groove underneath
Use Screws (6 pcs)
C
C
C
C
C
C
C
C
C
C
C
C
C
(4 pcs)
(4 pcs)
Top
right
C

Step 1 - continued
Assembly Instructions (Desk)
6
J
J
d:
e:
f:
f: C
d:
Place a small amount of
Glue into the groove on
the Shelf .
Carefully slide the Back
panel into the unit.
J
2
4
e:
Place a small amount of
Glue into the groove on
the Top panel .
J
3
Finished
front surface
3
unit.
C
Use Screws (4 pcs) to
Use Screws (2 pcs)
C
C
C
C
C
C
J
3
4
2
4
5
6
5
6
6
5
Groove
underneath
Top right and
left panels & onto
the unit.
5 6

7
Assembly Instructions (Desk)
Step 2
a:
b:
Attaching bottom panel
a:
onto the Back
9
8
9
C
Use Screws (2 pcs)
.
Right
Insert Dowels (5pcs)
into the Left side panel
and Back support
8
.
D
support
b:
onto the unit.
10
10
C
Use Screws (2 pcs)
Insert Dowels (2pcs)
into the Right side panel
.
D
9
8
10
8
C
D
D
D
D
D
C
C
C
D
D

Step 3
Assembly Instructions (Desk)
a:
b:
8
Screw Locking pins
into the Table top .
Attaching table top
F
Note:
Insert Locking pins
as far as shown.
Do not over tighten.
onto
1
1
C
Continued on next page.
F
Use Screws (2 pcs)
1
F
F
F
F
F
F
1
5
6
C
E
J
E
C
E
E
1
Insert Dowels (4pcs)
into the Table top .
E
b:
a:
Place a small amount
of Glue onto the joint’s
surfaces.
J
the unit.
56
J

Step 3 - continued
Assembly Instructions (Desk)
9
With help, carefully stand
top unit upright.
Warning:
The top unit is heavy.
Lift with care.
d:
Finishing the part of
Carefully locate the Table
top onto the unit.
1
Use a screwdriver to turn
Locking nuts clockwise
to lock.
G
Insert 6 Locking nuts
into the unit.
G
c:
d:
G
J
desk unit.
1
9 10
8
8
9
10
G
G
G
G
G
G
c: Place a small amount
of Glue onto the joint’s
surfaces.
J
J

Step 4
Assembly Instructions (Robe)
a:
b:
10
a:
H
I
A
11
12
13
A
19
17
Step 5
Attaching hinges and
rail supports
Door hinges ‘back
plates’ onto the Right side
panel .
H
I
11
Rail support onto the
Right side panel .
I
A
11
a:
Rail support onto the
Middle panel .
I
A
13
b:
Continued on next page.
Attaching middle panel
a:
Insert Dowels (13 pcs)
into the Front panel and
Bottom panel .
19
17
Insert Dowels (6 pcs) into
the Right and Left side
panels & .
11
D
12
Finished
front edge
Finished
front edge
I
I
I
A
H
I
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
back edge
D
Insert Dowels (3 pcs) into
the Middle panel .
D
13
A
I
H
I

Step 5 - continued
Assembly Instructions (Robe)
11
the Right and Left side
panels & onto the
unit.
Attaching side panels
19
17
b:
C
C
C
C
C
C
C
C
C
11
17
12
13
17
Step 6
b:
Position Front panel
onto the Bottom
panel .
17
19
13
C
12
11
back edge
back edge
c:
c:
C
Finished
front edge
back edge
Finished
front surface
19
Use Screws (3 pcs)
onto the unit.

Step 7
Assembly Instructions (Robe)
12
Step 8
O
15
15
16
C
C
C
C
back edge
Attaching top panel
the Top panel onto the
unit.
16
C
back edge
back surface
11
13
12
Fixing back panel
Attach Back panels
onto the unit using Nails
.
15
O
Important:
The unit MUST
be ‘square’ when
the back is attached.

Step 9
Assembly Instructions (Robe)
13
a:
Step 10
14
b:
NN
N
N
Attaching shelves
a:
lnsert Shelf supports
into the unit.
inserting the shelves.
Note:
Set the shelf
supports to the desired
height.
M
b:
Slide the Shelves
into the unit.
18
18
18
Locate Clothes rail into
the Rail supports .
M
A
With help, carefully stand
robe upright.
Warning:
The robe is heavy.
Lift with care.
H
I
R
R
I
H
K
B
Fix 2 Door hinges into the
Door panel using
Attach Handle using
Screw .
H
K
Fitting hinges to door
Screws .
14
I
B
Finished
front edge
I
H
M
A
N
before
R
R
14
R
Tear off the protective
backing from the Door
pads .
Stick the Door pads
onto the front edge of
Door panel .
R

Step 11
Assembly Instructions (Robe)
14
14
Hinge adjustment
Step 12
a:
With help, slot Door
hinges onto ‘hinge
plates’.
H
b:
Tighten screw shown to
lock hinges in position.
’See ‘Hinge adjustment
in step 12 if the door need
adjusting.
Hanging door
Continued on next page.
a:
To move door up or
down: loosen screws
shown and move door to
suit.
Once door are aligned,
re-tighten and insert 2
Screws into ‘hinge
plates’.
I
b:
a:
Door
b:
Door
I
b:a:
H
H
H
H

Step 12 - continued
Assembly Instructions (Robe)
15
d:
To move door in or
out: loosen screw shown
and move door to suit.
Re-tighten screws.
c:
To move door left or
right: loosen screw shown
and move door to suit.
Re-tighten screws.
d:
Door
c:
Door

Step 13
Assembly Instructions (Desk & Robe)
16
Fitting the unit
Use Screws (5 pcs) to
join the desk and robe
together.
C
C
C
C

Assembly Instructions (Desk & Robe)
Assembly is complete.
It is recommended that the
strap onto the top panel.
With help, move the unit into
position.
remove unit .
Drill 2 hole and insert Wall
plug .
wall strap using Screw .
Fixing to wall
Warning:
The unit is heavy.
Lift with care.
Warning:
Before drilling,
check wall for
hidden pipes and
cables.
L
P
17
Q
P
P P Q
Note: Wall plugs supplied are
for solid wall only.
be used for your wall, seek
professional advice if in doubt
X 2
wall
L
P
Top panel
Q
P
Step 14
Note: Before use allow the
glue to dry for 24 hours and
make sure the unit is secure.
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800

A Guide to - Wall Mounting & Fixings
Revision 2 - 7/10/09
Important note:
Types of walls
Care &
Maintenance
No.1 “General Purpose” wall plug
No.6 “Shield Anchor” wall plug
Heavy loads
No.3 “Cavity Fixing” wall plug
No.4 “Cavity Fixing-Heavy Duty”
wall plug
No.5 “Hammer Fixing” wall plug
No.2 “Plasterboard” wall plug
Generally aerated blocks should not
be used to support heavy loads, use
loads, general purpose wall plugs can
be used.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
For use with plasterboard partitions or
hollow wooden doors.
heavy loads such as shelving, wall
cabinets and coat racks.
For use with walls stuck with
is secure to the retaining wall.
For use when attaching light loads on
to plasterboard partitions.
Safety: Always check the fitting
and location to ensure your safety
in and around the home.
Fitting: From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.
You can use one of the following types of wall plug if your walls are made
of brick, breeze block, concrete, stone or wood.
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5:
drilled hole.
If plastic wall plugs
are supplied with your
product:
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualified
tradesperson if you are unsure.
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
responsibility of the installer.