Argos Sywell 643/8047 User manual

MADE IN
BRITAIN
Dimensions
Width - 38.5cm
Depth - 36cm
Height - 41.5cm
Sywell - Bedside
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 5 - 12/06/13
Important - Please read these instructions fully before starting assembly
Ruler - Use this ruler to help correctly identify the screws
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
643/8047
643/8171
643/8755
ALR2444
643/8975
643/9015
615/7263
615/5935
615/5849
Issue 2 - 23/03/11 - Added 3 Argos Codes - 615/7263, 615/5935, 615/5849
Issue 3 - 02/06/11 - Page 10 was incorrectly labelled as page 11.
Issue 4 - 10/06/13 - Title changed from Caspian to Sywell.
Side panels no longer have rebates - Left Side now D0272B and Right Side now D0273B.
The top Plinth has been taken out.
Back changed to X373-356.
NOTE:The AI shows 6 x Dowels and 4 x 40mm Confirmats but, the kit that is packed remains the same as the original.
Issue 5 - 12/06/13 - Errors on panels page on issue 4 and Janet had already sent it off.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 9kgs. Please lift
with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
Glue Safety - Take care when using glue, please follow the advice below
Skin contact: Remove contami-
nation by washing with soap and
water. This procedure should be
followed prior to aeting and
drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Components - Panels
Please check you have all the panels listed below
Glue Safety - Take care when using glue, please follow the advice below
Skin contact: Remove contami-
nation by washing with soap and
water. This procedure should be
followed prior to aeting and
drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
2
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• From time to time check that
there are no loose screws on
this unit.
Left Side (D0272B)
(399 x 353mm)
Drawer Divider - D0034A
145 x 249mm
waterfall
1Right Side (D0273B)
(399 x 353mm)
2Top (D0020A)
(382 x 356mm)
3
80%
Drawer Wrap - W161
943 x 95mm x3
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Plinth (D0022A)
(349 x 80mm) x 2
4Drawer Front (D0274A)
(345 x 157mm) x 2
5
Drawer Wrap (W161B)
(943 x 95mm) x 2
Drawer Base (T161B)
(299 x 330mm) x 2
7
6
8Back (X373-356)
(373 x 356mm)

Please check you have all the fittings listed below
Tools required
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 6
B
Metal dowel (F901) x 6
C
D
Large locking
nut (F900) x 2
E
Small locking
nut (F3) x 4
F
G
40mm Screw (F910) x 4
H
19mm Screw (F461) x 4
I
Rule Scissors Hammer Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Nail (F51) x 20
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J
9mm Screw (F74) x 4
K
9mm Screw (F73) x 8
Drawer runner (F1004) x 4
Handle (F923) x 2

Assembly Instructions
4
F
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
Prepare 2 drawer
fronts and 2 wraps
a: Screw 2 x metal
dowels into the holes
shown on the back of the
drawer front .
Note: Tighten metal
dowels up fully against
the panel.
b: Insert 2 small locking
nuts into the holes
shown on the drawer
wrap .
Note: Arrow on locking
nut must point towards
hole in edge of panel.
B
5
a:
b:
c:
F
7
B
Assemble drawers
a: Place drawer base
into the narrow slot on
the drawer wrap .
Fold wrap around the
base.
b: Turn drawer wrap
assembly over and push
onto the back of the
drawer front .
Note: Turn locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
c: Attach handle to
the drawer front using 2
screws .
6
6
7
5
F
B
B
B
5
5
5
7
7
7
7
B
B
F
a:
b:
B
F
7
F
C
F
Step 2
H
H
C
H
plain surface
x 2
x 2
x 2
x 2
x 2

Assembly Instructions
Use 2nd hole in from front of
Runner F1004 to fit 1st F73 then
fit other F73 to match other hole.
Rebated Edge
F73
COVERED EDGE
Use 2nd hole in from front of
Runner F1004 to fit 1st F73 then
fit other F73 to match other hole.
F1004
When you insert F900,
make sure the arrow is
pointing towards the hole
in the edge of the panel.
F900
F73
F1004
COVERED EDGE
5
1
E
A
Step 3
Prepare the left side
a: Place 2 runners on
the left side . Slide
back top of runner and
use 2nd hole from the
front to fit 1st screw .
b: Slide the runners
back the other way and
fit the 2nd screw into
the corresponding hole
in the left side .
c: Insert 1 large locking
nut into the left side.
Note: Arrow on locking
nut must point towards
hole in edge of panel.
Tap in wooden dowel
as shown.
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
1
K
I
I
Finished
front edge
I
K
Finished
front edge
a:
b:
c:
E
A
I
K
I
K1
I
I
Finished
front edge
A
E
1
1
E
10mm
A
1

A
Assembly Instructions
Use 2nd hole in from front of
Runner F1004 to fit 1st F73 then
fit other F73 to match other hole.
Rebated Edge
F73
COVERED EDGE
Use 2nd hole in from front of
Runner F1004 to fit 1st F73 then
fit other F73 to match other hole.
F1004
When you insert F900,
make sure the arrow is
pointing towards the hole
in the edge of the panel.
F900
F73
F1004
COVERED EDGE
6
Step 4
a:
b:
Finished
front edge
I
K
c:
I
K
I
K
Finished front edge
I
I
E
2
2
2
Prepare the right side
a: Place 2 runners on
right side . Slide back
top of runner and use
2nd hole from the front
to fit 1st screw .
b: Slide the runners
back the other way and
fit the 2nd screw into
the corresponding hole
in the right side .
c: Insert 1 large locking
nut into the right side.
Note: Arrow on locking
nut must point towards
hole in edge of panel.
Tap in wooden dowel
as shown.
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
2
K
I
I
E
A
Finished front edge
Finished front edge
2

G
G
Assembly Instructions
7
Step 5
Finished
front edge
G
A
Prepare the 2 plinths
Tap 2 wooden dowels
into the ends of the 2
plinths .
Note: The plinths will
only have one finished
surface.
4
4
4
2
4
Fit 2 plinths to the
right side
2 people are needed
here
a: Attach a plinth
near the finished front
edge of the right side
using the dowel already
fitted to it and secure
with screw .
b: Attach a plinth
near the back edge of
the right side and
secure with screw .
Support the plinth near
the back edge of the
unit until the left side
has been fitted in the
next step.
Fit left side
Push the left side
onto the dowels fitted to
the 3 plinths and
secure with 3 screws .
1
4
G
2
Step 7
Step 6
A
A
4
4
4
Finished surface
2
G
G
1
4
4
Plain chipboard
surface
x 2
Plain chipboard
surface
G

Assembly Instructions
8
G
Main unit
colour
Finished
front edge
Step 8
Step 9
Prepare top panel
Screw 2 metal dowels
into the top , as
shown.
3
B
Fit top
Push the top onto
side panels and .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the inside of the side
panels and .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
3
1 2
1 2
E
E
B
2
3
E
B
B
3
Plain chipboard
surface
2
1
3

Assembly Instructions
9
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back ,
white side down, onto
the unit.
Use the nail guide to
hold the nails vertical
and at the correct
distance whilst you nail
around the outside
edges of the back .
Stand the unit up
for the next step.
8
8
C
D
8
C
D
b:
Step 10 The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
C
D
b:
y
y
x
x
8