Argos Puerto Rico 641/8720 User manual

Puerto Rico - Single Trunk
641/8720
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400 800
Important –Please read these instructions fully before starting assembly
Dimensions
Width - 92cm
Depth - 49.6cm
Height - 45.6cm
Issue 1 - 19/07/10
641/8737

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fttings from the
plastic bags and separate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
We do not
recommend the
use of power
drill/drivers
as this could damage the unit.
Only use hand screwdrivers.
for
inserting screws,
Parts of the assembly will be
easier with 2 people.
Dispose of all packaging
carefully and responsibly.
This product has been produced
from natural timber; you may
notice some variation in the grain
and colour of different component
parts which is normal for furniture
produced using natural wood and
is not the result of any
manufacturing fault.
The product has been treated
with a wax and oil finish to
prevent dirt ingress and preserve
moisture.
On unpacking the
furniture you may notice an
odour due to this treatment;
this will disappear once the
furniture is unpacked and
assembled after a period of time.
This process may leave some
staining on the packaging
material; please take care to
ensure this does not transfer
to clothing or carpeted surfaces
during assembly.
Care and maintenance
Use an appropriate furniture
polish for natural wood
furniture and a dry cloth to
clean the product.
Avoid placing the furniture in
direct sunlight as this will cause
the timber to prematurely age.
From time to time check
that there are no loose
screws on this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.

Components - Panels
Please check you have all the panels listed below
2
1Top panel (91.6 x 46.2cm)
2Front panel (87.8 x 36.8cm)
4Side panel x 2
(45.8 x 43.7cm)
6Front plinth (91.8 x 9.2cm)
5Base panel (87.5 x 45.5cm)
3Back panel (87.8 x 36.8cm)
7Back plinth (91.8 x 9.2cm)
Bottom
Bottom
Bottom

3
Components - Fittings
Please check you have all the fittings listed below
If you have damaged or missing components,
call the Customer Helpline: 08456 400 800
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
0510 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Tools required
Phillips screwdriver
(medium & large)
Eye protection
(when using a
hammer or glue)
Small
hammer
Ruler/tape
measure
A
D
G
K
B
E
H
C
F
J
Closing System x 2Lock x 135mm Screw x 12
2m
Hinge x 2 Side Handle x 2
14mm Screw x 44 35mm Screw x 2220mm Screw x 4
Corner
Bracket x 6
Lock Plate x 1

Step 1
Assembly Instructions
4
Step 2
Fixing panels.
Two people required for
an easier assembly.
Fit front panel and
back panel to the side
panels .
Attach side panes at
the front panel and
back panel using
screws .
Note:
A flat surface is
required.
C
2
3
4
4
Bottom
C
C
C
4
42
3
2
3
C
7D
6
3
2
C
C
C
D
Fix front plinth to the
bottom front panel
using screws .
Fix back plinth to the
bottom back panel
using screws .
Make sure front
plinth and back plinth
are aligned to the
bottom edge of the side
panels and in line to the
side plinths.
Note:
Attach side panes at
the front plinth and
back plinth using
screws .
C
2
6
6
7
3C
7
6
4
D
7

Assembly Instructions
5
Step 3
Fixing base panel.
cabinet, after attach using
screws .
Fit base panel at the
Step 4
Fixing top panel.
Important:
With help, carefully
face the product up.
cabinet.
a: Attach hinges to the
pre drilled holes in the
top panel using screws .
Fit top panel at the
1
5
D
D
D
Bottom
5
D
a: b:
1
G
A
A
A
G
b: Fix the hinges in the
back panel using
screws .
Be sure that the top
panel is centered to the
cabinet prior a
Attention:
ttaching.
A
3
3

Assembly Instructions
6
Step 5
90º
90º
F
B
F
A
a: b: c:
Two people required for
an easier assembly.
a: O .90ºpen top panel
b: Attach closing system
to the pre drilled holes
in the side panels
using screws .
4
1
4
B
F
c:
Attention:
Ensure top panel
is
Attach
to the top panel
using screws .
closing system
90º prior to fixing.
1
F
A
4
4
1
F
2

Assembly Instructions
7
Step 6
Step 7
Attach corner bracketsin
side panels and front
plinth using screws .
to the pre drilled holes
Assembly is complete.
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400 800
a: b: c:
A
JK
A
4
4
2
1
A
1
E
a:Attach 2 side handles
in side panels using
screws .
to the pre drilled holes
J
4
A
b:Attach lock in top
panel using screws .
to the
pre drilled holes
4A
E
c:Attach lock plate
in front panel using
screws . 2
A
K
A
A
A
A
A
H
A
A
H