Argos Single Robe 234046 User manual

Ref. no HB 01.06Date: 30/07/09
Single Robe
Assembly Instructions - Please keep for future reference
Important - Please read these instructions fully before starting assembly
Dimensions
For all enquiries please contact : 0845 6002420
Width - 50cm
Depth - 59cm
Height - 210cm
234046

Safety and care advice
Important – Please read these instructionsfully before starting assembly
Note: if required the next
page can be cut out and used
asreference throughout the
assembly. Keep thispage with
these instructionsfor future
reference.
• Check you have all the
componentsand toolslisted on
pages2 and 3.
Remove all fittingsfrom the
plastic bagsand separate them
into their groups.
• Keep children and animals
away from the work area, small
partscould choke if swallowed.
• Make sure you have enough
space to layout the partsbefore
starting.
• Do not stand or put weight
on the panels, thiscould cause
damage.
• Assemble the unit asclose
to itsfinal position (in the same
room) aspossible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Note: Only apply the glue
once you are sure of the
assembly.
• The wall plugssupplied are
suitable for solid wallsonly.
It isimportant that the correct
type of fixing isused for your
wall, seek professional advice if
in doubt.
• Partsof the assembly will be
easier with 2 people.
• If using power tools, please
follow the safety instructions
supplied with the tools.
• We do not
recommend the
use of power drill/
driversfor inserting
screws, asthis
could damage the unit. Only use
hand screwdrivers.
• Warning: Before drilling,
check the wall for hidden pipes
and cables.
• Dispose of all packaging
carefully and responsibly.
• Warning: The unit weighs
approximately 44kgs.
Please lift with care.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screwson
thisunit.
• Thisproduct should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Care and maintenance
Skin contact: Remove
contamination by washing with
soap and water. Thisprocedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately. If possible
show product information or
label to the medical advisor.
Glue safety - Take care when using glue, please follow the advice below
2

1
4
4
5
6
7
2
RAW
3
3
Components - Panels
Please checkyou have all the panels listed below
1) Left end panel x1
2) Right end panel x1
3) Backpanel x1
4) Top/Bottom Panels x2
5) Shelf x1
6) Structural plinth x1
7) Rear base support rail x1

Wooden dowel x 8
Ruler - Use this ruler to help correctly identify the screws
Tools required
A
E
Metal dowel x 10
B
15mm Screw x 14 30mm Screw x 8
x 4
x 4
x 20
x 1
4MAx15 Screw x4 27mm x4 Spacer x2
C
I
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
F
D
K
M
SR
Q
VU
CY Z
W
P
O
N
L
Block x 1
12mm Screw x 8
clip hinge x 4 hinge mounting plate x 4 soft close x 2
G
J
Hanger rail
support x 2
15mm Screw x 8
25mm Nail x 30
x 4
x 2
x 4
H
25mm Screw x 16
hanging rail x 1
Long locking
nut x 10
0 0 20 30 40 50 60 70 80 90 00 0 20 30 40 50
0 2 3 4 5 6
Phillips screwdriver
(medium & large)
Spirit level
Flatblade screwdriver
(medium)
Small
hammer
Ruler/tape
measure
Drill
Ø 5mm Suitable drill bit
(for use with wall plug)
Eye protection
(when using a
hammer or glue)
mm
x 4
T
Components - Fittings For enquiries relating to spare parts please
contact : 0845 6002420
Please check you have all the fittings listed below
4

Assembly Instructions
Step 1
use cams
to top panel
use Knock-in plastic
fitting to bottom panel
4
4
7
6
E
E
O
O
Prepare panels
Top
Bottom
1
B
T
C
YP
Repeat with
the right side panel 2
100mm 80mm
R
F
RAW
The picture refersto the assembly of a
left hand door. For right hand door,
mount the hinge mounting plate on
right end panel.
important
5

Assembly Instructions
Step 2
Step 3
4
7
1
Back
Bottom
RAW
6
Top
Front
E
2
RAW
76
6

Assembly Instructions
Step 4
Step 5
Insert back panels
Fixing back panels Important:
The cabinet MUST
be ‘square’ when the
back is attached.
Note:
Q
For additional stability
secure back to height adjustable shelf
after assembly (step 14)
H
7

Assembly Instructions
Step 6
Step 7
Ø5mm
35
8

Assembly Instructions
Step 8
U
9

No.3 "Shield Anchor" Wall Plug
Heavy Loads
For use with heavier loads such as TV
& HiFi Speakers and Satellite Dishes etc.
No.4 "Cavity Fixing" Wall Plug
For use with plaster board partitions or
hollow wooden doors.
No.5 "Cavity Fixing - Heavy Duty"
Wall Plug
For use when fitting or supporting heavy
loads such as shelving, wall cabinets,
coat racks.
IMPORTANT:
When drilling into walls always check that there are no
hidden wires or pipes etc. Make sure that the screws and
wall plugs being used are suitable for supporting your unit.
Consult a qualified tradesperson if you are unsure.
HINTS:
1) General Rule Always use a larger screw and wall plug if you are not sure.
2) Ensure you use the recommended drill bit to match the wall plug and hole size.
3) Ensure you drill the hole horizontally, do not force the drill or enlarge the hole.
4) Take extra care when drilling high walls, ceilings and ceramic tiles. Ensure the plug is fitting below the ceramic
tile to avoid splitting or cracking.
5) Ensure wall plugs are well fitted and are a tight fit in the drilled hole.
Types Of Walls
You can use one of the following types
of wall plug if your walls are made of
brick, breeze block, concrete, stone,
wood or plaster board.
No.1 "Standard" Wall Plug
General Wall Materials
These come in various sizes and are made
from plastic or sometimes wood fiber.
No.2 "General Purpose" Wall Plug
Aerated / Breeze Block
Generally aerated blocks should not be
used to support heavy loads, use a
specialist fitting in this case.
For light loads, a General Purpose Plug
can be used.
No.6 "Hammer Fixing" Wall Plug
For use with walls stuck with plaster
board. The hammer fixing allows it to
be fixed to the wall rather than the plaster
board. Always check the fixing is secure
to the retaining wall.
CARE & MAINTENANCE
SAFETY
Always check the fitting and
location to ensure your safety in
and around the home.
FITTING
From time to time check the fitting
to ensure the wall plugs or screws
do not become loose.
Wall Mounting & Fixings
A Guide to