Argos Twister CD/DVD tower User manual

Twister CD/DVD tower
Assembly Instructions – Please keep for future reference 901 / 0864 D
901 / 0857 D
Dimensions
Width – 43 cm
Depth – 43 cm
Height – 92 cm
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 – 30/09/2011
Warning: 2 persons assemble recommended.

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
●Check you have all the
components and tools listed on
page 2 & 3.
●Remove all fittings from the
plastic bags and separate them
into their groups.
●Keep children and animals
away from the work area, small
parts could choke if swallowed.
●Make sure you have enough
space to layout the parts before
starting.
●Do not stand or put weight on
the product, this could cause
damage.
●Assemble the item as close to
its final position (in the same
room) as possible.
●Assemble on a soft level
surface to avoid damaging the
unit or your floor.
●We do not
recommend the use of
power drill/drivers for
inserting screws, as
this could damage the unit. Only
use hand screwdrivers.
●Dispose of all packaging carefully
and responsibly.
Care and maintenance
●Only clean using a damp
cloth and mild detergent, do
not use bleach or abrasive
cleaners.
●From time to time check that
there are no loose screws on this
unit.
●This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.

2
Components - Parts
Please check you have all the parts listed below
Top panel
(300 x 300 mm)
1
Divider x 2
(852 x 149 mm)
3
Side panel x 4
(852 x 138 mm)
2
Divider x 2
(852 x 149 mm)
4
Bottom panel
(300 x 300 mm)
5
Base panel
(430 x 430 mm)
7
Adjustable shelf x 20
(136 x 136 mm)
6
Turnplate
8
This way up
Inner face
This way up
Inner face

3
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
Tools required
Philips screwdriver Flatblade screwdriver
A
llen Key
(Provided)
Components - Fittings
If you have damaged or missing components,
call the Customer Helpline: 08456 400800
Please check you have all the fittings listed below
Wood dowel x 24 Metal dowel
x 4
Cam lock x 4
A
B
C
Bolt x 8
D
E
Screw x 26
Shelf
p
in x 80
F
G
Cover
p
ad x 26

4
Thiswayup
Innerface
Assembly Instructions
Step 1
LayDividers and
on the ground with the
Way up marks face
upward as shown.
Insert Wood dowels
into the indicated holes
inDividers and .
Step 2
Push Divider onto the
untapped edge of Side
panel ,makesurethe
wood dowels enter the
corresponding holes.
Note: make
sure the big
hole in Side
panel and the Way up
mark face inwards as
shown.
Secure with 3
Screws .
Repeat to assemble the
other Divider and
other2Dividers
ontoSidepanels .
2
3
E
E
3
4
4
3
A
4
3
3
4
A
Note: Way up mark.
2
2
3
4
2
A

5
Assembly Instructions
Step 3
Insert Wood dowels
into the indicated holes
in Divider .
Push one section of
panels and from
Step 2 to the other
section of panels
and ,makesurethe
wood dowels enter the
corresponding holes.
Secure with 3
Screws .
Repeat to assemble the
other half section.
Step 4
Insert Wood dowels
into the indicated holes
inDividers and .
Push one half section
from Step 2 to the other
section, make sure the
wood dowels enter the
corresponding holes.
Secure with 4
Screws .
4
3
E
2
3
2
2
4
2
3
2
4
4
E
4
E
3
E
A
A
A
A
A
A

6
Assembly Instructions
Step 5
Insert Wood dowels
into the centre holes of
Top panel .
Screw Metal dowels
into the outer holes of
Top panel .
Step 6
Firmly Push Top panel
onto end of Panel ,
and sothatthe
Wood dowel and Metal
dowels enter the
corresponding holes.
Insert 4 Cam locks
into the big holes in Side
panels .
Note: Longer
leg of the
cross on the
Cam lock must face
towards end of panel (as
shown).
Then, using a Flatblade
screwdriver, screw the
Cam locks clockwise
until they are ‘hand tight’.
2
C
2
C
1
1
A
B
1
A
B
1
2
1
3
4
2
C
2
3
4
3
4
Note: Long leg of the
cross

7
Assembly Instructions
Step 7
Insert Wood dowels
into the centre holes of
Bottom panel .
Step 8
lay the box unit from
Step 6 on its side.
Firmly Push Bottom
panel onto end of
Panel , and
so that the Wood dowel
enter the corresponding
holes.
Secure with 4
Screws .
5
E
5
5
A
A
E
5
2
3
4

8
Assembly Instructions
Step 9
Lay the Base panel
on the ground.
Secure Turnplate
onto the threaded holes
in Base panel with
Bolts .
Step 10
Stand item on the Top
panel. Locate the base
part to the Bottom
panel ,securethe
Turnplate onto the
threaded holes in Bottom
panel, using Bolts by
Allen key.
Note: 2
persons
assembly
recommended. Revolve
the Base panel to secure
the bolt one by one
through hole in Base
Panel asshown.
Note: Do not
tighten the
Bolts until all
Bolts have been properly
located.
7
D
7
5
D
8
7
8
D
5
7
5
D
8
Base Panel hidden for clarity.
8

9
Assembly Instructions
Step 11
Turn the unit upright.
InsertShelfpins into
the side holes at desired
height.
Step 12
Place Adjustable shelves
ontoShelfpins .
Cover all visual screw
holes with Cover
pads .
Assembly is complete.
6
F
F
F
If you need help or have damaged or missing parts, call the Customer Help Line: 08456 400800
Home Retail Group plc. Avebury, 489-499 Avebury Boulevard. Milton Keynes. MK9 2NW
6
G