Argos Malibu 428/3445 User manual

MADE IN
BRITAIN
Dimensions
Malibu - 2 Door Robe
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 1 - 21/05/15
Important - Please read these instructions fully before starting assembly
ALR3190
428/3445
414/7756
424/3973
424/7302
412/3402
Width - 75cm
Depth - 49.5cm
Height - 181cm

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 49kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
overbalance protector kit
supplied or, an alternative fixing
method of your choice.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
80%
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
12
6
5
Hanging Rail (FHR704)
(70.4cm long)
7
89
3
Left Side (DF3568)
(180.8 x 49.6cm)
Right Side (DF3569)
(180.8 x 49.6cm)
Top/Base (DF3570)
(71.6 x 49.4cm) x 2
4Shelf (DF3579)
(71.6 x 47.6cm)
Back Rail (DF3576)
(71.6 x 9.2cm)
Plinth (DF3575)
(71.6 x 9.2cm)
Door (DF3573)
(167.7 x 35.3cm) x 2 Back (X1711-742)
(171.1 x 74.2cm)

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Rule
Tools required
Rule
ScissorsSquare
Spirit
level
Hammer Bradawl
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Step
ladder
Electric drill
(only use
when drilling
into walls)
A B C
D E
G H
40mm Screw (F910) x 16
I J
F
K
25mm Screw (F50) x 2
13mm Screw (F63) x 14 Nail (F51) x 31
Hinge (F522) x 6
Hinge plate (F523) x 6
Handle (F631) x 2
Strap Screw Washer x 2
Overbalance protector kit (F269) x 1
Wooden dowel (F22) x 10
Plastic Nail (F91) x 4
Rail holder
(F1014) x 2

Finished
front edge
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
Step 2
Prepare the left side
Fit 3 hinge plates onto
the left side making
sure that the slot is
facing towards the
finished front edge.
Push a rail holder into
the left side . Make
sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
I
1
G
D
1
I
I
I
G
D
I
1
G
D
Prepare the right side
Push a rail holder into
the right side . Make
sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
Fit 3 hinge plates onto
the right side , making
sure that the slot is
facing towards the
finished front edge.
G
2
I
2
D
I
I
IFinished
front edge
I
2

Assembly Instructions
5
Step 3
Step 4
A
A
10mm
A
Prepare the 2
top/base panels
Tap 2 wooden dowels
into each of the 2
top/base panels .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
A
3
3
Finished
front edge
x 2
B
BFinished
front edge
Finished
front edge
B
B
Fit the top and base
panels to the right
side
Push the top and base
onto the right side
and secure them with
screws .
B
3
2
3
2
Finished
front edge
3
3Top/Base (DF3570)
(71.6 x 49.4cm) x 2
4Shelf (DF3579)
(71.6 x 47.6cm)

Assembly Instructions
6
Step 5
Step 6
Step 7
Prepare the plinth and
back rail
Tap 2 wooden dowels
into the plinth .
Tap 2 wooden dowels
into the back rail .
Note: The back rail has
a finished top edge.
A
5
A
6
Finished
top edge
A
A
A
6
A
5
A
A
Finished
front edge
Prepare the shelf
Tap 2 wooden dowels
into the shelf .
A
4
4
Finished
front edge
B
B
Fit the shelf
Push the shelf onto
the right side and
secure it with screws .
B
4
2
2
4

Assembly Instructions
7
Step 8
Step 9
Fit the plinth and back
rail
Push the plinth onto
the right side and
secure it with screw .
Push the back rail
onto the right side
and secure it with screw
. .
B
5
2
Finished
top edge
B
B
6
B
6
2
Note: Support the
back rail until the left
side has been fitted
in the next step.
2
5
Fit the left end
Push the left side
onto the top and base ,
the shelf , the plinth
. and the back rail
and secure with 8
screws .
1
3
4
65
BB
B
B
B
B
B
B
B
1
3
3
5
6
4

Assembly Instructions
8
Step 10
Step 11
b:
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back .
Note: Nails should be
spaced about 150mm
apart.
9
F
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
9yy
yy
xx
xx
F
9
Fit the plastic nails
Tap 2 plastic nails
into the bottom edge of
each of the sides and
. .
Carefully stand the
unit up for the next
step.
E
1
2
E
EE
E
1
2
Warning: The
unit is heavy.
Lift with care.

Assembly Instructions
9
Step 12
Prepare the 2 doors
Push fit 3 hinges into
each of the 2 doors .
Secure each hinge with
2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.
D
J
8
90
J
J
D
D
J
D
D
J
D
D
8
x 2
Fit the hanging rail
Push the hanging rail
into the rail holders .
7
G7
G
7
Step 13