Argos Romana 305/1836 User manual

Romana - Bedside Chest
305/1836
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400 800
Important –Please read these instructions fully before starting assembly
Dimensions
Width - 42cm
Depth - 36cm
Height - 55cm
Issue 1 - 25/04/13
305/1843

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and separate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
We do not
recommend the
use of power
drill/drivers
as this could damage the unit.
Only use hand screwdrivers.
Parts of the assembly will be
easier with 2 people.
Dispose of all packaging
carefully and responsibly.
for
inserting screws,
This product has been produced
from natural timber; you may
notice some variation in the grain
and colour of different component
parts which is normal for furniture
produced using natural wood and
is not the result of any
manufacturing fault.
The product has been treated
with a wax and oil finish to
prevent dirt ingress and preserve
moisture.
On unpacking the
furniture you may notice an
odour due to this treatment;
this will disappear once the
furniture is unpacked and
assembled after a period of time.
This process may leave some
staining on the packaging
material; please take care to
ensure this does not transfer
to clothing or carpeted surfaces
during assembly.
Care and maintenance
Use an appropriate furniture
polish for natural wood
furniture and a dry cloth to
clean the product.
Avoid placing the furniture in
direct sunlight as this will cause
the timber to prematurely age.
From time to time check
that there are no loose
screws on this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.

Components - Panels
Please check you have all the panels listed below
2
top
top
underside
1Top panel
(42 x 36cm)
2Right side panel
(53.4 x 33cm)
3Left side panel
(53.4 x 33cm)
4Back panel
(45 x 36.2cm)
8Drawer bottom
(28.6 x 27cm)
5Right front frame
(53.4 x 4.5cm)
6Left front frame
(53.4 x 4.5cm)
7Base panel
(34.4 x 31.4cm)
9Drawer front
(28.4 x 12cm)
11 Drawer back
(26 x 12cm)
10 Drawer side x 2
(30 x 12cm)
15 Top front frame
(33 x 4.5cm) 16 Bottom front frame
(33 x 4.5cm)
17 Block x 4
(6.6 x 2cm)
12 Side drawer runner x 2
(26.6 x 3.5cm)
13 Front plinth
(42 x 9.2cm) 14 Side plinth x 2
(33.8 x 9.2cm)

G
3
Components - Fittings
Please check you have all the fittings listed below
If you have damaged or missing components,
call the Customer Helpline: 08456 400 800
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
0510 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Tools required
Phillips screwdriver
(small & medium)
Eye protection
(when using a
hammer or glue)
Small
hammer
Ruler/tape
measure
A
D E
C
Wooden dowel x 14
2m
F
H
B
I
Metal dowel x 8
Locking
nut x 8 Drawer
handle x 1 Nail x 14
19mm Bolt x 1
14mm Screw x 2
35mm Screw x 20
30mm Screw x 14

Step 2
Step 1
Fixing right front frame
to the right side panel
.
(Two people required for
an easier assembly)
Insert right side panel
into right front frame
through joints.
a:
Note:
Before fixing the
blocks into
place it is important to
ensure that the slot and
groove of parts and
are fully pushed together
and lined up correctly at
the top and bottom.
c: Fix front frame through
blocks using screws
.
b: Place blocks in the
to the side panel using
screws .
positions shown. First fix
Assembly Instructions
4
Fixing left front frame
to the left side panel
.
(Two people required for
an easier assembly)
Insert left side panel
into left front frame
through joints.
a:
Note:
Before fixing the
blocks into
place it is important to
ensure that the slot and
groove of parts and
are fully pushed together
and lined up correctly at
the top and bottom.
c: Fix front frame through
blocks using screws
.
b: Place blocks in the
to the side panel using
screws .
positions shown. First fix
2
2
3
3
2
Top
5
5
Top
6
6
66mm
66mm
130mm
272mm
5
17
17
D
a: b: c:
a: b: c:
D
2
17
Yes!No!
D
D
3
Yes!No!
5
17
17
17
D
D
66mm
66mm
130mm
272mm
17
17
6
3
6
17
17
17
17
D
D
Attention!
74mm
Attention: correct
position of panel.
Attention!
74mm
Attention: correct
position of panel.

Assembly Instructions
5
Step 3
Step 4
Insert dowels into the
indicated parts.
A
F
1
Fitting Metal dowels.
Do not over tighten.
Screw metal dowels
into top panel and side
panels and .
Insert metal
dowels as far as
shown.
Note:
F
23
2
3
7
2x
12
A
A
A
A
A
1
2
3
F
F
F
F

Assembly Instructions
6
Fixing side drawer
runner.
Fit side drawer runner
to the right side panel
then fix it using screws
as shown.
Repeat step 5 for the
left side panel and side
drawer runner.
Assembling the cabinet.
Insert top front frame
and bottom front frame
into holes on left side
panel .
oles position
on bottom front
frame .
Attention!
The h
Step 5
Step 6
Step 7
2
2
D
D
Assembling the cabinet.
With help, fit base panel
to the right side panel.
Make sure rounded edge
is facing front.
Insert 2 locking nuts
into base panel where
shown.
Use a screwdriver to turn
locking nuts clockwise
to lock.
Do not over tighten.
G
G
7
12
12
12
15
16
Attention!
16
3
15
16
3
16
7
3
G
G
7
Rounded edge.
G
G

Assembly Instructions
7
Step 8
Step 9
Fixing top panel.
With help, fit top panel
to the cabinet.
Insert 4 locking nuts
into side panels where
shown.
Use a screwdriver to turn
locking nuts clockwise
to lock.
Do not over tighten.
Important:
After attaching the
top panel, With help,
carefully lay down the
product.
G
1
G
Assembling the cabinet.
Insert 2 locking nuts
into base panel where
shown.
After attaching
side panel, With help,
carefully stand product
upright.
With help, fit left side
panel to the base
panel and front frames
as shown.
Use a screwdriver to turn
locking nuts clockwise
to lock.
Do not over tighten.
Important:
G
G
G
G
2
G
G
G
G
G
G
1
2
7
7

Assembly Instructions
8
Step 10
Step 11
Fixing back panel.
MUST
With help, carefully stand
the product upright.
Cabinet be
‘square’ when back panel
is attached.
Attach back panel
using nails .
Important:
4
a: Fix side plinths to
the side panels using
screws .
Make sure side
plinths are aligned to
the bottom and front
edges of the side panels.
Note:
b: Fix front plinth
to the bottom front frame
using screws .
Make sure front
plinth is aligned to the
bottom edge of the side
panels and in line to the
side plinths.
Note:
C
C
14
13
14
13
a:
b:
a: 14
14
13
C
C
C
4
I
I
I
I

Assembly Instructions
9
Step 12
Insert drawer into unit.
With the back of the
drawer past the front
frames, use a hammer to
tap dowels in flush to
drawer sides. This is a
safety catch to stop
drawer falling out.
.
Assembly is complete.
A
A A
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400 800
a:
Drawer assembly.
a: Attach drawer sides
to the drawer front
using screws .
b: Slide drawer bottom
into slots on drawer
sides and position drawer
back in place.
c: Carefully lay down the
drawer holding drawer
back , press the
drawer sides and fix
them using screws .
Attach handle to the
drawer using bolt ,
then fix handle plate to
the drawer using screws
. Make sure handle
plate is aligned before
fixing.
C
10
9
11
H
11
C
E
B
C
C
C
C
c:
b:
H
E
B
10
10
9
8
11
Step 13
8