Argos 737/6672 Manual

Corners Large TV Unit
Care & Instruction Manual
Please read and retain these instructions for future reference
737/6672
724/3932
724/8841
-

1
Safety and Care Advice
Important –Please read these instructions fully before startingassembly
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
Handy Hints
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Regularly check and ensure
that all bolts and fittings are
tightend properly.

Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline:
Argos = 0345 6400800
2
Top panel (120 x 38cm)
1
Bottom panel (116.8 x 36.2cm)
2
Middle panel (116.8 x 34.1cm)
3
Right side panel
(24 x 43.5cm)
4Left side panel
(24 x 43.5cm)
5
Left support
(34 x 22.9cm)
7
Right door panel (37.9 x 24cm)
12
Middle support (19.8 x 11.6cm)
9
Shelf panel (40 x 33.9cm)
10
Front panel (116.8 x 5.9cm)
11
Back panel (92.2 x 43.5cm)
8
Right support
(34 x 22.9cm)
6
Left door panel (37.9 x 24cm)
13
Small back panel x 2 (36.1 x 20.5cm)
14
Pilot holes for
guidance only
Unfinished
back edge

3
Ruler - Use this ruler to help correctly identify the screws
Tools required
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Small
hammer
Ruler/tape
measure
Drill
Eye protection
(when using a
hammer or glue)
7mm Suitable drill bit
(for use with wall plug)
The screws length is measured from the head to the point (30mm screw shown).
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
Components - Fittings
A B C
D
G
E F
H
Handle x 2
50mm Screw x 14 30mm Dowel x 639mm Locking pin x 20
15mm Locking nut x 20 30mm Screw x 2
I
J K
Plastic support x 3
Door hinge x 4Door pad x 4 15mm Screw x 16
(This screw is included in
the door hinge bag)
15mm Screw x 6

4
Assembly Instructions
Step 1
a:
b:
Attaching hinges
a: Use Screws to fix
the Door hinges ‘back
plates’ onto the Right side
panel and Left side
panel .
I
4
5
H
b: Screw Locking pins
into the Right side panel
and Left side panel
.
B
5
4
Note:
Insert Locking pins
as far as shown.
Do not over tighten.
5
Insert Dowels into the
Right side panel
and
Left side panel .
C
4
I
H
H
I
I
H
CB
B
B
B
CB
B
B
B
H
I
4
5
4
5
B
I
H
I
H
Note: Only two screws
(not four) are fitted to the
door hinge back plate.

Assembly Instructions
5
c:
b:
b: Use Screws to fix the
Front panel onto the
Bottom panel .
Step 2
a: Use Screws to fix
Plastic supports onto
the Front panel .
a: Attaching bottom and
middle panel
J
K
11
K
11
Note: Be sure the edges
of the Plastic supports
even with the edges of
the Front panel .
11
2
J
c: Screw Locking pins
into the Middle panel .
B
3
Note:
Insert Locking pins
as far as shown.
Do not over tighten.
Continued on next page.
K
K
K
JJ
J
J
K
K
K
B
B
B
B
J
J
J
11
2
3
11
K
B
11

6
Assembly Instructions
Step 2 - continued
e:
d:
Insert Dowels into the
Right support and Left
support .
6
7
C
Continued on next page.
d: Use Screws to fix
the Middle support
onto the Middle panel .
A
3
9
e: Use Screws to fix
the Right support and
Left support onto the
Shelf panel .
A
7
10
6
A
A
A
A
C
C
A
A
3
9
10
6
7
Unfinished back edge
Unfinished back edge

Assembly Instructions
7
f:
g:
g: Use Screws to fix
Bottom panel onto the
unit.
2
A
f: Carefully locate the
Middle panel onto the
unit.
3
Insert 4 Locking nuts
into the unit.
D
Use a screwdriver to turn
Locking nuts clockwise
to lock.
D
Step 2 - continued
D
D
D
A
A
A
A
D
3
6
2
7
6
D
7

8
Assembly Instructions
Step 3
b:
a:
Attaching right and left
side panel
a: Carefully locate the
Left side panel onto
the unit.
5
Insert 4 Locking nuts
into the unit.
D
Use a screwdriver to turn
Locking nuts clockwise
to lock.
D
b: Carefully locate the
Right side panel onto
the unit.
4
Insert 4 Locking nuts
into the unit.
D
Use a screwdriver to turn
Locking nuts clockwise
to lock.
D
D
D
D
D
2
4
3
2
3
5
D
D
D
D
D
D

Assembly Instructions
Step 4
9
Attaching back panel a:
Use Screws to fix the
Back panel onto the
Middle panel and
Bottom panel .
A
8
3
2
Slide small back panels
into the unit.
14
a: Insert Dowels into
the Back panel .
C
8
b: With help, carefully
stand the unit upright.
Warning:
The unit is heavy.
Lift with care.
b:
Finished front surface
8
3
2
14
2
8
3
5 4
14
C
A
A
A
A
C
Unfinished back surface