Argos New Penton User manual

New Penton - 2 Door Wardrobe
257/8853
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400 800
Important –Please read these instructions fully before starting assembly
Dimensions
Width - 85cm
Depth - 51cm
Height - 180cm
Issue 1 - 14/05/14
275/0705
266/9690

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and separate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Parts of the assembly will be
easier with 2 people.
Dispose of all packaging
carefully and responsibly.
This product has been produced
from natural timber; you may
notice some variation in the grain
and colour of different component
parts which is normal for furniture
produced using natural wood and
is not the result of any
manufacturing fault.
The product has been treated
with a wax and oil finish to
prevent dirt ingress and preserve
moisture.
On unpacking the
furniture you may notice an
odour due to this treatment;
this will disappear once the
furniture is unpacked and
assembled after a period of time.
This process may leave some
staining on the packaging
material; please take care to
ensure this does not transfer
to clothing or carpeted surfaces
during assembly.
Care and maintenance
Use an appropriate furniture
polish for natural wood
furniture and a dry cloth to
clean the product.
Avoid placing the furniture in
direct sunlight as this will cause
the timber to prematurely age.
From time to time check
that there are no loose
screws on this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.

Components - Panels
Please check you have all the panels listed below
2
1Right side panel (178 x 49cm)
3Back panel x 2 (170 x 40.2cm)
4Right front frame (178 x 9.2cm)
2Left side panel (178 x 49cm)
6Door x 2 (160.2 x 31.8cm)
5Left front frame (178 x 9.2cm)
7Larger H profile (128 x 2cm)
10 Front frame x 2 (68.6 x 6.5cm)
14 Block x 7 (10 x 2cm)
9Base panel x 2 (79.4 x 47.4cm)
top
underside
underside
top
8Top panel (85 x 50.4cm)
11 Smaller H profile (36 x 20cm)
12 Hanging rail (78.8 x 2.2cm)
13 Cross rail x 4 (28 x 4.5cm)

G
3
Components - Fittings
Please check you have all the fittings listed below
If you have damaged or missing components,
call the Customer Helpline: 08456 400 800
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
0510 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Tools required
Phillips screwdriver
(small & medium)
Eye protection
(when using a
hammer or glue)
Small
hammer
Ruler/tape
measure
A
D E
C
Wooden dowel x 12
2m
F
H
B
I
JK L
MN
P
O
Wall strap x 1
14mm Screw x 47 30mm Screw x 16
35mm Screw x 28 40mm Screw x 6 22mm Bolt x 4
Metal dowel x 12 Locking
nut x 12 Nail x 40
Door
handle x 2
Door
hinge x 6 Clip x 4
Plug x 4 Hanging rail
support x 2 Washer x 2
Q
Door
spacer x 1

Assembly Instructions
4
Yes!No!
4
Step 2
Step 1
Fixing right front frame.
(Two people required for
an easier assembly).
a: Insert right side panel
into right front frame
through joints.
c: Fix front frame through
blocks using screws
.
a: b: c:
a: b: c:
Note:
Before fixing the
blocks into
place it is important to
ensure that the slot and
groove of parts and
are fully pushed together
and lined up correctly at
the top and bottom.
4
Yes!No!
5
1
4
14
14
1
D
D
14
1
D
D
14
2
14
D
D
1
14
14
14
4Attention: correct
position of panel.
Top
14
14
14
Attention: correct
position of panel.
Top
2
5
b: Place blocks
between the two marks on
the front frame as shown.
First fix to the side panel
using screws .
Fixing left front frame.
(Two people required for
an easier assembly).
a: Insert left side panel
into left front frame
through joints.
c: Fix front frame through
blocks using screws
.
Note:
Before fixing the
blocks into
place it is important to
ensure that the slot and
groove of parts and
are fully pushed together
and lined up correctly at
the top and bottom.
14
14
D
D
14
b: Place blocks
between the two marks on
the front frame as shown.
First fix to the side panel
using screws .
5
2
25

Assembly Instructions
5
Step 3
Step 4
Insert dowels into the
indicated parts.
Fix hanging rail support
in the pre marked
holes on right side panel
and left side panel
using screws , as
shown.
A
1
Fitting Metal dowels.
Screw metal dowels
into right side panel .
Insert metalNote:
dowels as far as
shown.
Do not over tighten.
Repeat step 3 for the
left side panel .
G
2
A
A
A
12
9
2x
and
N
1
2
G
G
G
B
B
N
12
and

Step 5
Inserting front frame.
Insert the front frames
into holes on right
side panel , as
shown.
10
Assembly Instructions
6
Step 6
1
10
10
Fixing base panel.
With help, fit base panels
to right side panel .
Attention!
Round edge on
base panels must be
facing front.
Insert 6 locking nuts
base p sinto anel where
shown.
Use a screwdriver to turn
locking nuts clockwise
to lock.
Do not over tighten.
9
9
Attention:
9
9
1
1
1
H
H
H
H
H
H

Assembly Instructions
7
Step 7
Step 8
Fixing left side panel.
With help, place left side
panel properly
ensuring dowels and front
frames are all fit into
their holes at the same
time.
Insert 6 locking nuts
into base panels where
shown.
Use a screwdriver to turn
locking nuts clockwise
to lock.
Do not over tighten.
Attach block to the
base panel and front
frame using screws
as shown.
Important:
After attaching
block, with help, carefully
lay down the product.
2
10 2
10
9
9
10
14
14
H
H
H
H
H
H
D
D

Assembly Instructions
8
Step 9
Fixing top panel.
With help, fit top panel
to the cabinet then fix it
using screws .
Make sure round edge is
facing up.
Important:
After fixing the top
panel, with help, carefully
stand the product upright.
Step 10
8
8
Insert hanging rail into
the supports.
12
12
E
E
E
8

Assembly Instructions
9
Step 11
Step 12
Fitting hinges to doors.
Attach hinges in the
pre marked holes on door
using screws as
shown.
Fix cross rails in the
pre drilled holes on door
using screws .
Repeat step 11 for the
other door.
13
6
13
K
6
13
6
6
B
C
C
C
K
K
K
B
B
Hanging doors.
With help, centralise
a:
the door in the opening
of the cabinet using the
door spacer to ensure
correct spacing, as
shown.
a:
b:
View from behind
6
Q
b: From inside the
cabinet fix the hinges
using screws as
shown.
Note:
To ensure the
alignment of the doors is
correct, centralise the
doors in the opening
before attaching to the
cabinet.
B
Q
Q
Q