Argos Hamlin 152/8062 User manual

Hamlin - 2 Doors Robe
152/8062
Assembly Instructions - Please keep for future reference
Issue 1 - 28/10/13
151/7358
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400 800
Important –Please read these instructions fully before starting assembly
Dimensions
Width - 80,2cm
Depth - 55,8cm
Height - 192cm
151/2683
h y g e n a

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and separate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Parts of the assembly will be
easier with 2 people.
Dispose of all packaging
carefully and responsibly.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Care and maintenance
Avoid placing the furniture in
direct sunlight as this will cause
the timber to prematurely age.
Use a dry cloth to clean the
product, furniture polish is
not recommended.
From time to time check
that there are no loose
screws on this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.

Components - Panels
Please check you have all the panels listed below
2
1Right side panel (190 x 54cm)
5Back panel x 2 (180.8 x 39.1cm)
2Left side panel (190 x 54cm)
3Door x 2 (179 x 35cm)
8Base panel (77 x 54cm)
top
underside
underside
top
7Top panel (80.2 x 55.8cm)
12 Hanging rail (76.2 x 3cm)
underside
10 Bottom frame (77 x 9.6cm)
9Shelf (77 x 52.7cm)
4Door knocker x 2 (178 x 8cm)
6H profile (179 x 1.8cm)
Unfinished bottom frame
(77 x 9.6cm)
11

Components - Fittings
Please check you have all the fittings listed below
If you have damaged or missing components,
call the Customer Helpline: 08456 400 800
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
P
O
Door
hinge x 6
N
3
A B C
Wooden dowel x 20
Ruler - Use this ruler to help correctly identify the screws
0510 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Tools required
Phillips screwdriver
(small & medium)
Eye protection
(when using a
hammer or glue)
Small
hammer
Ruler/tape
measure
2m
D
14mm Screw x 28
E F
IG H
L
JK
M
Metal dowel x 12
Locking
nut x 12 Nail x 67 Nail x 4
Plastic
feet x 4
Washer x 2 Plastic
cap x 12 Wall strap x 1
L shaped
bracket x 6
Hanging rail
support x 2
25mm Screw x 1416mm Screw x 1
14mm Screw x 24

Assembly Instructions
4
Step 1
Insert dowels into the
indicated parts.
Fix hanging rail support
in the pre marked
holes on right side panel
and left side panel
using screws , as
shown.
A
L
1
2B
12
and
8
9
10
A
A
A
A
A
L
B
Step 2
B
K
10
L1mm
Attention:
11
B
10
K
K
11
K
10
Unfinished side
to face up.
Fixing L shaped
brackets.
Fix L shaped brackets
in the bottom frame
and unfinished bottom
frame using screws
, as shown.
Attention:
Leave gap1mm
from the edge of the
bars as shown.
Fix L shaped brackets to
the unfinished side in
bottom frame .
K
11
10
11
A
A
K
K

Assembly Instructions
5
Step 3
Fitting Metal dowels.
Screw metal dowels
into right side panel ,
left side panel and top
panel .
Insert metalNote:
dowels as far as
shown.
Do not over tighten.
F
F
7
1
2
7
F
F
1and
F
2F
Step 4
1and 2
P
P
P
PC
P
Fitting hinges.
Loosen screw in doora:
hinge and separate
the ‘back plate’.
12
b: Attach ‘back plates’
in the pre marked holes
on right and left side
panels and using
screws .
a: b:
P
P
C

Assembly Instructions
6
Step 5
G
GN
G
G
8
10
9
2
11
K
Fixing panels and
frames.
With help, fit base panel
, shelf , bottom
frame and unfinished
bottom frame to left
side panel .
Finished side of
base panel to
face up and finished
edges of base panel
and shelf to face front.
4Insert locking nuts
base p and shelfinto anel
where shown
Use a screwdriver to turn  
locking nuts clockwise
to lock 
Do not over tighten.
After screwing locking
nuts, insert plastic caps
.
Fix bottom frames and
in the side panel
through L shaped
brackets using screws
.
8
10
9
G
G
N
Finished side and edges
2
11
G
G
8
9
8
11
10
B
K
B

Assembly Instructions
7
Step 6
Fixing right side panel.
Place right side panel
properly ensuring dowels
and bottom frames are all
fitted into their holes at
the same time.
I 4 lnsert ocking nuts
into b nelase pa and shelf
where shown
Use a screwdriver to turn  
locking nuts lockwisec
to lock 
Do not over tighten.
After screwing locking
nuts, insert plastic caps
.
Fix bottom frames and
in the side panel and
base panel through L
shaped brackets using
screws . GN
G
1
G
G
K
B
1
G
G
N
K
B
Step 7
Fixing top panel.
With help, carefully lay
down the product.
With help, fit top panel
to the cabinet.
Insert 4 locking nuts
into el ereside pan s wh
shown
e a screwdriver to turnUs   
locking nuts ockwisecl
to lock 
Do not over tighten.
After screwing locking
nuts, insert plastic caps
.
7
G
7
G
N
G
G
GGN
8
10
11
10
11
K

Assembly Instructions
8
Step 10
Step 8
Fixing back panels.
Important:
Cabinet beMUST
‘square’ when back panels
are attached. Make sure
back panels are in flush
with the edge of the top
panel prior to fixing.
a: Attach the right back
panel first using nails
.
Note: Back panel´s
finished side to face inside
b: Position profile onto
back panel (just attach).
c: Carefully slot the
second back panel into
the profile and fix it to the
cabinet using nails .
655
5
5
6
H
H
H
H
5
H
6
5
H
12
L
Step 9
Insert hanging rail into
the supports .
L
Attach plastic feet.
Attach p in
lastic feet
the bottom edge of the
right and left side panels
using nails .
After attach plastic feet,
with help, carefully stand
the product upright.
I
J
I
J
J
12
Attention!
Make sure nails
are fully nailed.

Assembly Instructions
9
Step 11
Step 12
a: b:
P
C
C
P
P
P
Fitting hinges to doors.
Insert hinges in the
a:
holes on door , as
shown.
b: Attach hinges in the
the door using screws ,
as shown.
Repeat step 11 for the
other door.
3
3
P
P
C
3
3
Hanging doors.
a: With help, slot door
hinges onto ‘hinge
plates’.
P
C
P
P
a:
b:
b: Tighten screw shown
to lock hinges in position.
Repeat and fora b
other door.
See ‘hinge adjustment’ in
step 14 if the doors need
adjusting.