Argos Star 7607729 User manual

Pull out Desk - Star
Dimensions
Length - 60cm
Depth - 96cm
Height - 74,6cm
Weight - 13,1kg
Issue 2 - 10/01/18
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
0045 7668 8055 or e-mail: order@flexa.dk
Assembly Instructions - Please keep for future reference 7607729

1
Safety and Care Advice
Important – Please read these instructions
fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• During assembly children
should be kept away from the
product due to possible risk of
injury.
• Make sure you have enough
space to layout the parts before
starting.
•This product is suitable for
children in the age range 3 to
adult
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• Do not use this item if any
components are missing or
damaged
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could
damage the unit. Only use hand
screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Assembly to be carried out by
a competent adult only.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• Regularly check all fastenings
to ensure that they properly
tightened.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
• This product is suitable for
children in the age 4-12 years.
Maximum load on tabletop 20
kg. Maximum load on shelf 7 kg.
Care and maintenance
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Components - Parts
Please check you have all the parts listed below
2
If you have damaged or missing components,
call the Customer Helpline: 0045 7668 8055
Guide list x2
(94.2x4.0x3.2cm)
4
Table top x1
(95.9x60x1.6cm)
7
No. 4301-1609591-40
Side panel right x1
(70.9x17x1.5cm)
1
No. 15-01507091-40
Side panel left x1
(70.9x17x1.5cm)
2Base/Shelf x2
(53.4x15.2x1.5cm)
3
No. 15-01507093-40 No. 15-01505341-40
No. 12-03209423-40
Back panel x1
(69x54.6x0.3cm)
6
No. 4309-030690
Front panel x1
(53.4x9x1.6cm)
5
No. 4301-1605342-40

Ø15/Ø6.0x24mm Spacer x1
1.2x20mm Nail square x25
4.0x40mm Chipboard screw x1
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
Components - Fittings
Tools required
Phillips
screwdriver
(medium)
Allen key
4mm incl.
Flatblade
screwdriver
(medium)
Small
hammer
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
No. 4033-004
3
Ø7x34mm for Ø5 Minifix bolt x6
A
Ø15x9.5mm Minifix cam x6
B
E
Ø5x30mm Dowel x4
C
D
4.0x15mm Chipboard screw x4
F
No. 4022-006
G
Ø26x28.5mm Castor x2 7.0x40mm Confirmat screw x8
H
No. 3903-40040No. 3908-70040
J
M
4.5x60mm Chipboard screw x2
4.0x12mm Chipboard screw x8
i
L
4.5x40mm Chipboard screw x2
20x20x16x2mm Angle x4
No. 3901-45060
No. 3901-40012
No. 3901-45040
No. 4008-021
K
No. 3940-000241
No. 3930-05030
No. 4003-002
No. 3933-15010
No. 4020-005
No. 3902-40015

4
C
C
C
G
1
2
1
2
3
3
G
G
G
G
A
A
A
M
M
M
L
L
L
7
5
Assembly Instructions
Step 1
Attach the minifix bolts
Ato the table top 7.
Attach two angles Mto
the front panel 5with
screws L.
Attach the dowels Cto
the side panels 1and
2.
It may be necessary
to tap the dowels in
very gently with a small
hammer.
Attach the base and shelf
3to the side panels 1
and 2with the screws
G
Step 2
Step 3

5
Assembly Instructions
B
1
2
7
Step 4
Attach the table top 7to
the side panels 1and
2with the minifix cams
B.
Attach the front panel
5to the table top 7
with screws L. Follow
the marking holes on the
table top 7bottom side.
Attach the front panel
5to the side panels 1
and 2with angles M
and screws L. Follow
the marking holes on the
front panel 5.
Step 5a
Step 5b
B
1
1
7L
L
L
5
5
2
2
MM
L
L
L

6
Assembly Instructions
2
13
7
F
6
F
3
3
D
D
D
E
2
Step 6
Attach the back panel 6
to the bottom base 3
with nails F.
Attach the castors D
to the base 3with the
screws E.
Step 7
E
D

Assembly Instructions
7
If you need help or have damaged or missing parts,
call the Customer Helpline: 0045 7668 8055
E-mail: order@flexa.dk
Ref.no. 44-01747-20 B Stand: 100118 Page 8 (81-31705-20)
Attach the guide list 4
under the bedside into
the legs with the screws
J.
Note: The guide list
ends should be flush
with the bedside rails.
Attach the table top 7to
the guide list 4.
Attach the other guide
list 4to the bedsides
and table top 7with the
screws i.
Attach the spacer Kto
the table top 7with the
screw Hto prevent the
table from falling out.
Assembly is complete.
Step 8
K
H
i
7
7
4
4
H
i
K
K
Step 9
44
J
J
J
40mm
i
70mm