Argos Walton 166/2629 User manual

MADE IN
BRITAIN
Dimensions
Width - 39.5cm
Depth - 59.5cm
Height - 74cm
Walton - 2 Drawer Filer
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 17/10/13
Important - Please read these instructions fully before starting assembly
ALR2914
166/2629

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 22kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
Glue Safety - Take care when using glue, please follow the advice below
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Components - Panels
Please check you have all the panels listed below
2
1
80%
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
2
Left Drawer Side (W528LH)
(386 x 150mm) x 2
Right Drawer Side (W528RH)
(386 x 150mm) x 2
Drawer Back (W528)
(309 x 150mm) x 2
3
4 6
9 10
7 8
File Bar (FBAR336)
(336mm) x 4
5
Left Side (D2372A)
(718 x 570mm)
Right Side (D2373A)
(718 x 570mm)
Top (D2371A)
(394 x 593mm)
File Front (D2376A)
(387 x 338mm) x 2
Back (X708-385)
(708 x 385mm)
Base (D2374A)
(359 x 567mm)

Please check you have all the fittings listed below
Tools required
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 8
B
Metal dowel (F901) x 12
C
D E F
K
G
Large locking
nut (F900) x 8
13mm Screw (F63) x 8
Nail (F51) x 15
Small locking
nut (F3) x 4 13mm Screw (F52) x 8
Knock-in Peg (F171) x 8
JJ CL Runner
(F904) x 2
DL Runner
(F906) x 2
a
Jb
Jc
JdDR Runner
(F905) x 2
CR Runner
(F903) x 2
19mm Screw (F461) x 4
I
I
Handle (FWALTON) x 2
H

Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
x 2
x 2 x 2
x 2
B
Step 2
Prepare the 2 file
fronts
Screw 2 metal dowels
into the holes shown on
the back of the file front
. .
Note: Tighten metal
dowels up fully against
the panels.
B
7
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .
Note: Arrow on locking
nut must point towards
hole in edge of panel.
Step 3
D
9
10
Fit the file bars
Push 2 file bars into
each pair of drawer
sides and .
D
Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.
D
10
9
B
B
7
D
10
9
9 10
5
5
5

Assembly Instructions
5
Step 4
Step 5
x 2
Step 3
Attach the drawer
sides to the file front
Push the left drawer side
. and right drawer side
. onto the back of the
file front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
9
10
7
D
9
10
B
B
D
D
10
7
9
K
K
10
9
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
8
9 10
8
K
9 10
K
Kx 2
8

Assembly Instructions
6
Step 6
80%
Fit the runners
Position the runner ,
onto the left drawer side
. as shown, making
sure that the front of the
runner is pushed up
against the back of the
file front .
Use a bradawl to mark
the fixing positions, then
secure with 2 screws .
Fit runner to the
right drawer side
using the same method.
Attach the handle
Attach a handle to
each of the the 2 file
fronts using 2 screws
. .
Step 7
7I
I
H
x 2
x 2
c
J d
E
9
10
7
J d
J c
Runners must be
pushed up against
the file front
E
E
E
E
10
9
J
7
7
H
I
Turn the drawer assemblies over

A
A
Assembly Instructions
7
Step 8
I b
F
F
Fit runners to the left
side
Fit the 2 runners
marked ‘CL’ to the left
side .
The 1st screw uses
the 2nd hole in from the
front of the runner .
Fit the 2nd screw into
the corresponding hole
in the left side .
Finished
front edge
B
C
10mm
A
1
Finished
front edge
B
C
C
1
J a
F
1
J a
F
1
Step 9
Finish preparing the
left side
Tap 2 wooden dowels
into the left side .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Screw 2 metal dowels
into the left side .
Note: Tighten metal
dowels up fully against
the panels.
Insert 2 large locking
nuts into the left side
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
B
1
C
1
A
1
J a
CL
F
F
F
F
J a
CL
CL
J a
CL
F
F
CL
CL
B

A
A
Assembly Instructions
8
Step 10
80%
Fit runners to the
right side
Fit the 2 runners
marked ‘CR’ to the right
side .
The 1st screw uses
the 2nd hole in from the
front of the runner .
Fit the 2nd screw into
the corresponding hole
in the right side .
Step 11
J b
F
2
J b
F
2
Finished
front edge
Finished
front edge
C
C
B
Finish preparing the
right side
Tap 2 wooden dowels
into the right side .
Screw 2 metal dowels
into the right side .
Insert 2 large locking
nuts into the right
side .
B
2
C
2
A
2
2
2
CR
F
F
CR
F
F
CR
CR
B
J b
CR
CR
F
F
J b
J b

Finished
front edge
Finished
front edge
Assembly Instructions
9
Step 12
Step 13
C
C
C
A
A
A
A
C
Plain chipboard
surface
Finished
front edge
Prepare the base
Tap 4 wooden dowels
into the base .
Insert 4 large locking
nuts into the base
A
4
4.
C
Join the right side and
base
Push the base onto
the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the base .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
B
C
C
C
4
2
4
4
4
plain
chipboard
surface
2