Argos Hallingford 802/6622 User manual

Spare Parts
Visit: www.argos-support.co.uk
Email: [email protected]
Call: 0330 016 1114
Customer Support
Call: 0345 640 2020
Hallingford
Issue 4 - 02/09/20
802/6622 767/2565 930/0842 856/7985

Safety
Important - Please read these instructions fully before starting assembly
• WARNING: To prevent
possible overbalancing this unit
must be secured to a wall using
the overbalance protector kit
supplied.
• A unit that is allowed to topple
can cause serious or fatal injury.
In addition to wall fixing the unit,
place heavy items on the lower
shelves, do not put any heavy
objects on top of the unit and
never allow children to climb or
hang on drawers, doors or
shelves.
• Refer to guide after section 16
for wall fixing information.
Care Advice
• Check you have all the
components and tools listed on
relevant pages.
• Remove all fittings from the
specified plastic bag and
separate them into their groups.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• Assembly videos are
available throughout
these instructions by
scanning in the QR
codes.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean with a damp cloth.
• Warning: This unit weighs
approximately 14kgs.
Please lift with care.
• Assembly to be carried out by
a competent adult only.
• During assembly children
should be kept away from the
product due to possible risk of
injury.
• Installation shall only be
carried out exactly according to
the manufacturer’s instructions -
otherwise a safety risk can
occur if incorrectly installed.
• Do not use this item if any
components are missing or
damaged.
• Regularly check all fastenings
to ensure they are properly
tightened.

Cabinet Panels
Drawer Panels Note: the internal drawer panels are grey
155.6 x 37.2cm
DF-00010160
636 x 16cm
DF-00022259
735 x 13cm
WRP-00000156
835 x 13cm
WRP-00000157
255.6 x 37.2cm
DF-00010161
434.1 x 6cm x 2
DF-00018114
553.5 x 36.6cm
X535-366
337.5 x 39.6cm
DF-00022673
931.95 x 34.7cm
TDF-00022245
10 30.85 x 13cm
WRP-00000463

Fittings Use these drawings to
correctly identify the fittings
Bag 1
F900
A
F901
F22
Ax 8 Bx 8 Cx 8 D
F73
x 12
F91
Ex 4
F171GY
Bag 2
Ix 12
A
F901
Ax 6 K
F74
x 6
F607
Gx 6
F639
Hx 6
F51
x 20
F
Jx 6
F63
F474
F503
Nx 1
Lx 3
Mx 6
F652

Finished
front edge
Finished
front edge
F900
A
F901
F22
Ax 8 Bx 8 Cx 8 D
F73
x 12
F91
Ex 4
F51
x 20
F
1
Dx 12
Mx 6
www.youtube.com/watch?v=yG4xtiJJeSg
Fitting Ball Bearing Runners
Bag 1
2nd hole
A B
A B
2nd hole
1
2

2
Cx 4
1
2
1
2
3
Bx 4
4
Ax 4
2
1

Finished
front edge
5
6
Cx 4
Bx 4
4 4
7
4
1
4

Finished
front edge
8
9
4
2
10
Nx 1
Only use 1 Screw
to fit the Bracket
Finished
front edge
3
Ax 4

Finished
front edge
3
11 x 4
12
A = B
Make sure measurement A and B
are the same before attaching part 5
A
AB
B
www.youtube.com/watch?v=FeaI6541z7o
Squaring up a Chest and fitting the Back Panel

13
Fx 20 5
14
Ex 4
5
15

16
Nx 1
WARNING!
In order to prevent overturning
this product must be used with the
wall attachment device provided
Slide the Bracket against the wall. Fit the 2nd screw supplied with
the Bracket into the underside of the Top panel.
Mark the slot at the back of the Bracket for drilling into the wall.
Wall fixings are not supplied as they will need to suit the wall type.
Note: Take care when drilling the wall that you do not drill
into any pipes, wires etc.
If in doubt, consult an expert.
See the next section for a guide
to wall mounting and fixings
Top

Important note:
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
If plastic wall plugs
are supplied with your
product:
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
using incorrect fixings is the
responsibility of the installer.
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualified
tradesperson if you are unsure.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5: Ensure wall plugs are well fitted and are a tight fit in the
drilled hole.
Types of walls You can use one of the following types of wall plug if your
walls are made of brick, breeze block, concrete, stone or wood.
Generally aerated blocks should not
be used to support heavy loads, use
a specialist fitting in this case. For light
loads, general purpose wall plugs can
be used.
For use with plasterboard partitions or
hollow wooden doors.
For use with walls stuck with
plasterboard. The hammer fixing allows
it to be fixed to the wall rather than the
plasterboard. Always check the fixing
is secure to the retaining wall.
For use when attaching light loads on
to plasterboard partitions.
For use when fitting or supporting
heavy loads such as shelving, wall
cabinets and coat racks.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
No.1 “General Purpose” wall plug No.3 “Cavity Fixing” wall plug No.5 “Hammer Fixing” wall plug
No.2 “Plasterboard” wall plug
No.4 “Cavity Fixing-Heavy Duty”
wall plug
No.6 “Shield Anchor” wall plug
Heavy loads
A Guide to Wall Mounting & Fixings
Care &
Maintenance
Safety: Always check the fitting
and location to ensure your safety
in and around the home.
Fitting: From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.

Drawer Assembly
17
B
Gx 6
18
7
8
Ax 6
6
F171GY
Bag 2
Ix 12
A
F901
Ax 6 K
F74
x 6
F607
Gx 6
F639
Hx 6 Jx 12
F63
www.youtube.com/watch?v=InNBV_uuMmo
Drawer Assembly
x 3
x 3
x 3
x 3

6
x 3
x 3
x 3 x 3
20
19 x 2
7
8
9
21
Ix 6
10 10

x 3
22
Ix 6
24
Hx 6
23
Jx 6 Lx 3

ALR3647
25
Starting with the Bottom Drawer and working your way up, slide both its Runners forward and
locate the Drawer Sides between them, lining up the holes in the Drawer Sides with the 2nd
'threaded' holes in the Runners.
Working from the inside of the Drawer, insert 2 screws through the Drawer Sides and out into the
2nd threaded hole in the Runner.
Note: Do not overtighten the screws.
If they catch on the Runner you may need to loosen them slightly.
www.youtube.com/watch?v=yG4xtiJJeSg
Fitting Ball Bearing Runners
Kx 6
Warning: Use a screwdriver
to position the runners as
they could have sharp edges
1st
2nd
3rd
Assembly is complete