Argos Zest 267/8454 User manual

MADE IN
BRITAIN
Dimensions
Width - 77.5cm
Depth - 40cm
Height - 82cm
Zest - Media Unit
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 4 - 13/10/14
Important - Please read these instructions fully before starting assembly
ALR3044
267/8454
Issue 2 - 02/07/14 - Cat Code changed to 267/8454.
Base panel size changed to 775 x 395mm.
Screws for the feet changed to F81 (SC2800).
Amended the assembly so that the base panel is now fitted before the feet.
Issue 3 - 02/10/14 - Range name changed to Zest
Issue 4 - 13/10/14 - Drawer Back is now 693 x 124mm.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 30kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 1, 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.
Tools required
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Electric drill
(do not use for
fitting screws)

Components - Panels
Please check you have all the panels listed below
2
80%
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
1 2
9
Back (X791-769)
(791 x 769mm)
Left Drawer Side
(W370-124LH)
(370 x 124mm) x 2
Right Drawer Side
(W370-124RH)
(370 x 124mm) x 2
10
11
12 13 14
Left Side (D2960A)
(765 x 395mm)
3
Right Side (D2961A)
(765 x 395mm)
5Horizontal (D2980A)
(741 x 394mm)
6Top (D2959A)
(775 x 396mm)
7
8Drawer Front (D2956A)
(753 x 192mm) x 2
Loose Shelf
(D2964A)
(362 x 392mm)
4
Upright (D2962A)
(375 x 393mm)
Drawer Back (W693-124)
(693 x 124mm) x 2
Door (D2965A)
(387 x 375mm)
Drawer Base (T702-367)
(700 x 367mm) x 2
Base (D2955A)
(775 x 395mm)

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A B C
D
G H I
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
JL
Wedgefix (F639) x 8
13mm Screw (F63) x 1613mm Screw (F52) x 12
40mm Screw (F910) x 6
Metal dowel (F901) x 14 Large locking
nut (F900) x 10
Small locking
nut (F3) x 4
Bracket (F327) x 1
13mm Screw (F79) x 1
K
O
R
Foot
(F233) x 4
Knock-in Peg (F171GY) x 8
M
Shelf stud (F110) x 4
N
SR Runner (F160) x 2
b
L Runner (F161) x 2
Sc
L Runner (F159) x 2
Sa
R Runner (F162) x 2
Sd
350mm long
Q
P
Hinge Plate
(F521) x 2 Hinge (F520) x 2
Nail (F51) x 20
F
32mm Screw (F72) x 5
E
38mm Screw (F81) x 8
Handle (F894GRN) x 5

Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
8
x 2
x 2
x 2
x 2
A
B
A
C
C
Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on either surface of the drawer sides.
Make sure that the small groove is on the inside, as shown.
CC
910
Step 2
Prepare the 2 drawer
fronts
Screw 2 metal dowels
into each of the 2 drawer
fronts .
Note: Tighten the metal
dowels up fully against
the panels.
A
8
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
C
9
10
Attach the drawer
sides to the drawer
fronts
Push the left drawer sides
. and right drawer sides
. onto the back of the
drawer fronts .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
9
10
8
C
C
9
10 9
10
A
A
8

Assembly Instructions
5
Step 4
8
K
K
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
12
9 10
8
11
9 10
12
11
11
K
Attach the handles
Attach 2 handles to
each of the drawer fronts
. using screws .
Note: Do not
overtighten the screw.
O
F
8
9 10
x 2
x 2
x 2
K
K
12
9
11
9
10
12
10
F
O
F
O
8

Assembly Instructions
6
Step 7
Fit the wedgefixes
Turn the drawer
assemblies over and
slide 4 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
J
x 2
x 2
J
J
J
J
J
Step 8
S d
Fit runners to the
drawers
Fit the runner to the
bottom edge of the left
drawer side , as
shown, making sure that
it is pushed up against
the back of the drawer
front . Use a bradawl
to mark the fixing
positions, then secure
with 2 screws .
Fit the runner to the
bottom edge of the right
drawer side using the
same method.
10
S c
9
8
H
S d
Runners must be
pushed up against
the drawer front
H
H
S c
H
H
10
9
8

Assembly Instructions
7
Step 9
S b
G
Finished front edge
G1st
screw
2nd
screw
G3rd
screw
S b
Finished front edge
H
Prepare the right side
Screw 2 metal dowels
into the right side .
Insert 2 large locking
nuts into the right
side . .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Fit 2 hinge plates to
the right side making
sure that the slot is
facing towards the
finished front edge.
Fit 2 runners to the
right side .
The 1st screw uses
the 2nd hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
Fit a screw into the
2nd hole in at the top of
the runner .
B
2
S b
2
G
G
H
S b
Step 10
Prepare the horizontal
Insert 4 large locking
nuts into the
horizontal .
B
5
G
G
S b
GH
G
G
S b
GH
B
B
P
P
P
A
A
A
2
2
P
B
2
B
B
B
B
5
Green
edge
Green
edge

Assembly Instructions
8
Step 11
Step 12
Fit the horizontal to
the right side
Push the horizontal
onto the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the horizontal .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
2
5
B
B
5
A
B
5
2
Prepare the left side
Screw 2 metal dowels
into the left side .
Insert 2 large locking
nuts into the left side
. .
Fit 2 runners to the
left side .
The 1st screw uses
the 2nd hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
Fit a screw into the
2nd hole in at the top of
the runner .
S a
G
Finished front edge
G
1st
screw
2nd
screw
G
3rd
screw
S a
Finished front edge
H
B
1
S a
1
G
G
H
S a
G
S a
G
G
H
G
S a
G
G
H
B
B
A
1
A
A
1
Green
edge Green
edge
Green
edge

Assembly Instructions
9
Step 13
Step 14
Fit the left side
Push the left side
onto the horizontal .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the horizontal .
5
1
Prepare the upright
Insert 2 large locking
nuts into the upright
. .
Step 15
B
3
B
B
3
Fit the upright
Fit the upright onto
the horizontal using 2
screws .
3
5
D
D
D
3
5
Green
edge
Green
edge
Green
edge
1
5
B
5
Step 8 – Turning over the drawer assembly is not required to fit the runners, as already the correct way on the previous step.
Step 13 – do you need to add B to the diagram to show position of Lge locking nuts?