Argos Atlas 157/3309 User manual

MADE IN
BRITAIN
Dimensions
Atlas - Double Robe Carcass
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 2 - 05/02/14
Important - Please read these instructions fully before starting assembly
ALR2955
157/3309
152/7458
151/4739
Width - 100cm
Depth - 59.5cm
Height - 212.5cm
There is the option of
purchasing an Internal 3
Drawer Chest that can be
placed inside your Robe
IMPORTANT
This unit MUST be fixed to a wall
using both of the brackets supplied.
Issue 2 - 05/02/14 - The holes for the front feet have come forward by 32mm to improve stability.
Overbalance Bracket and Screw increased to 2.
Note added at Step 13 to emphasise the unit must be fixed to a wall and must be level and square.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 49kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
80%
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
1Universal End (D2396A)
(2074 x 591mm) x 2
2
3
Hanging Rail (FHR960)
(960mm long) x 2
4
Top/Base (D2395A)
(1000 x 592mm) x 2
Fixed Shelf (D2397A)
(968 x 590mm)
5Back (X2100-994)
(2100 x 994mm)

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 2
B
Metal dowel (F901) x 4
C
D E
Large locking
nut (F900) x 4
F
G H I
L
O
Nail (F51) x 40
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J
M
K
N
see malibu fitment mk2 for large number of panels and fittings
Rail Holder
(F891) x 4
Allen Key (F36) x 1 50mm Screw (F49) x 12
19mm Screw (F461) x 4
Handle (F323) x 2 Hinge (F328) x 8
25mm Screw (F50) x 6
13mm Screw (F63) x 24
13mm Screw (F79) x 2
Bracket (F327) x 2
Feet (F854) x 6
Tools required
Rule
Scissors
Spirit
level
Hammer Bradawl
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Step
ladder
Electric drill
(only use
when drilling
into walls)
Square
mm 10 20 30 40 50 60 70 80 90 100 mm 10 20 30 40 50 60 70 80 90 100

Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
Finished
front edge
Prepare the left end
Refer to step 1 and, if
you have chosen to fit 1
hanging rail, screw 2
metal dowels into the
left end .
Note: Tighten the metal
dowels up fully against
the panels.
To fit the rail holder ,
screw through its top
hole with screw and
into the shallow mark
hole drilled in the left end
. . Make sure that it is
fitted straight, in line with
the panel edges and
then fit another screw
using the lower hole.
Are you fitting 1 or 2
hanging rails or, a
shelf pack?
Step 2
If you are just
fitting 1 hanging
rail, the fixed
shelf will need
to go here.
Follow Steps 2
and 3.
Only follow Steps 2 and 3 if you are just fitting 1 hanging rail.
If you are fitting 2 hanging rails, follow Step 4 and 5.
If you are fitting 2
hanging rails, the
fixed shelf will
need to go here.
Follow Step 4
and 5.
J
K
J
K
B
K
J
B
B
1
1
B
K
1
J
If you are just
fitting 1 hanging
rail, the fixed
shelf will need
to go here.
Follow Steps 2
and 3.
There is an option of
inserting an Internal
3 Drawer Chest into
your Robe
If you are fitting 2
hanging rails, the
fixed shelf will
need to go here.
Follow Step 4
and 5.
There is an option of
inserting an Internal
3 Drawer Chest into
your Robe

Assembly Instructions
5
Step 3Only follow Steps 2 and 3 if you are just fitting 1 hanging rail.
If you are fitting 2 hanging rails, follow Step 4 and 5.
Step 4
Prepare the right end
Refer to step 1 and, if
you have chosen to fit 1
hanging rail, screw 2
metal dowels into the
right end .
Note: Tighten the metal
dowels up fully against
the panels.
To fit the rail holder ,
screw through its top
hole with screw and
into the shallow mark
hole drilled in the right
end . Make sure that
it is fitted straight, in line
with the panel edges and
then fit another screw
using the lower hole.
B
K
J
J
1
1
B
B
K
1
Finished
front edge
Finished
front edge
Prepare the left end
Refer to step 1 and, if
you have chosen to fit 2
hanging rails, screw 2
metal dowels into the
left end .
Note: Tighten the metal
dowels up fully against
the panels.
To fit the 2 rail holders
screw through the top
hole with screw and
into the shallow mark
hole drilled in the left end
. . Make sure that they
are fitted straight, in line
with the panel edges and
then fit another screw
using the lower hole.
B
K
J
J
B
B
1
1
J
K
J
K
B
K
1
K
Only follow Steps 4 and 5 if you are fitting 2 hanging rails.
If you are just fitting 1 rail, follow Step 2 and 3.
J
K
J
K

A
Assembly Instructions
6
Step 5Only follow Steps 4 and 5 if you are fitting 2 hanging rails.
If you are just fitting 1 rail, follow Step 2 and 3.
B
B
K
1
Finished
front edge
Prepare the right end
Refer to step 1 and, if
you have chosen to fit 2
hanging rails, screw 2
metal dowels into the
right end .
Note: Tighten the metal
dowels up fully against
the panels.
To fit the 2 rail holders
screw through the top
hole with screw and
into the shallow mark
hole drilled in the right
end . Make sure that
they are fitted straight, in
line with the panel edges
and then fit another
screw using the lower
hole.
B
K
J
J
1
1
J
K
J
K
B
K
Step 6
Prepare the fixed shelf
Tap 2 wooden dowels
into the fixed shelf .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 4 large locking
nuts into the fixed
shelf .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
A
C
3
3
C
10mm
A
C
C
A
C
C
3
Finished
front edge

Finished
front edge
Finished
front edge
Assembly Instructions
7
Step 7
Step 8
Join the fixed shelf to
the right side
Push the fixed shelf
onto the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the fixed shelf .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
The following steps show the fixed shelf near the top of the unit.
You may have fitted it in the centre of the unit.
B
C
3
1
1
3
C
C
3
Fit the left side
Push the left side
onto the fixed shelf .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the fixed shelf .
1
3
C
3
Finished
front edge
1
3
If you have fitted the
2 metal dowels in this
position, the fixed
shelf will go here.
The following diagrams will show the fixed
shelf at the top end of the unit.
You may have fitted it in the middle of the unit.

Finished
front edge
Finished
front edge
Assembly Instructions
8
Step 9
Step 10
Fit the base
Attach the base to
the ends using 6
screws and tighten
them using the allen key
. .
Prepare the base
Screw the 6 feet into
the shallow mark holes
on the base using
screws .
M
2
G
2
1
F
E
G
M
M
M
M
M
M
Finished
front edge
E
F
F
F
F
F
F
2
1
1
2

y
Assembly Instructions
9
Step 11
Step 12
F
F
F
2
E
F
F
F
Finished
front edge
1
1
Fit the top
Attach the top to the
ends using 6 screws
and tighten them using
the allen key .
2
1F
E
2
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of
the back .
Note: Nails should
be spaced about
150mm apart.
Stand the unit up
for the next step.
5
D
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
5
Warning: The
unit is heavy.
Lift with care.
y
y
x
b:
D
5
Unit colour on
the top surface
x