Argos Tolga 346/0111 User manual

Dimensions
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Assembly Instructions - Please keep for future reference
Tip : To prevent damage,
we recommend that you
build your unit on the
carton(s) it was packed in.
Height - 40,2cm
Depth - 38,2cm
Width - 73,4cm
Tolga - Storage Box
Argos = 03456 400 800
238/5273
248/5128
258/9945
346/0111
339/2117
345/8013
258/9945 345/8013 OAK
248/5128 339/2117 BLUE
238/5273 346/0111 PINK
Issue 2 - 25/11/14
DR825201
20kg

1
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
•
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
that all bolts and fi ttings are
tightend properly.
Handy Hints
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
Glue safety - Take care when using glue, please follow the advice below•
Important – Please read these instructions fully before starting assembly
Safety and Care Advice
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• Check you have all the
components and tools listed
on the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Assembly should be carried out
by a competent adult only.
• do not use this item if any
components are missing
or damaged.
• this item is suitable for childeren
from the age of 6.

Please check you have all the panels listed below
Components - Panels If you have damaged or missing components,
call the Customer Helpline:
2
03456 400 800
Drawer Front 1
(688 x 370 x 18mm)
1
P4141
Top x 1
(734 x 382 x 18mm)
2
P5028
Drawer Back x 1
(634 x 250 x 15mm)
3
P6101 Drawer Base x 1
(634 x 305 x 15mm)
4
P6100
Plinth x 2
(694 x 92 x 15mm)
5
P7060
Right Drawer Side x 1
(323 x 250 x 15mm)
7
P6102
Side x 2
(384 x 380 x 18mm)
6
P2045
Left Drawer Side x 1
(323 x 250 x 15mm)
8
P6103

Please check you have all the fittings listed below
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
Tools required
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Small
hammer
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
0102030405060708090 100 110 120 130 140 150
0123456
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
The screwslength ismeasured from thehead to the point (30mm screw shown).
3
IHG
F
E
D
CB
A
Locking screw x 12 (5x24mm)
FK1011
Chipboardscrew x 10 (3x15mm)
FK1311
15mm
Large locking nut x 12 (15x12mm)
FK1012
Expando dowel x 8 (5x11mm)
FK10561
Expando housing x 8 (20x12mm)
FK1051
Wood dowel x 18 (8x30mm)
FK1411
Wheel x 5
FK1244
Peg, brown x 1
FK1234
Glue x 2
FK1510
Spirit level Setsquare

Step - 1
Step - 2
Step - 3
Assembly Instructions
2x
4
6
AA
AA
6
A
A
A
A
5
B
B
B
B
6
AA
AA
6
A
A
A
A
5
B
B
B
B
6
AA
AA
6
A
A
A
A
5
B
B
B
B
Screw 24mm locking
screw Ainto side 6.
Note: look carreful for the
right postion.
Note: Insert 24mm locking
screw Aas far as shown.
Do not over tighten.
Screw 24mm locking
screw Ainto side 6.
Note: look carreful for the
right postion.
Note: Insert 24mm locking
screw Aas far as shown.
Do not over tighten.
Insert large locking nuts B
into Plinth 5.
Make sure the ‘arrow’ on
locking nuts Bpoints
towards the hole in the
edge of 5.
Repeat this step on second
plinth 5.
Finished
front edge
Finished
front edge

Assembly Instructions
Step - 5
5
Step - 4
5
6
5
6
F
F
F
F
F
F
F
H
Attaching panels
Position both side 6onto
plinth 5on both sides.
Use a screwdriver to turn
locking nuts clockwise to
lock.
Put drop of glue Hinto the
6 holes of top 2.
Put dowels Finto the
holes of top 2.
Finished
front edge
2
2

2
Assembly Instructions
Step - 7
6
Step - 6
D
H
5
6
5
6
6
2
3
D
D
Attaching top
Put drop of glue Hinto the
6 holes of side 6.
Position the 6 dowels H
of top 2onto the 6 holes
of side 6.
Screw expando dowel B
into drawer back 3.
Note: Insert expando
dowel Bas far as shown.
Do not over tighten.
Screw expando dowel D
into drawer back 3.
Note: Insert expando
dowel Das far as shown.
Do not over tighten.

F
H
B
Assembly Instructions
Step - 9
Step - 10
7
Step - 8
Finished
front edge
Finished
front edge
8
F
F
F
F
D
D
B
B
7
F
F
F
F
D
D
B
B
8
7
D
Screw expando dowel D
into left drawer side 8.
Note: Insert expando
dowel Das far as shown.
Do not over tighten.
Insert large locking nuts B
into left drawer side 8.
Make sure the ‘arrow’ on
locking nuts Bpoints
towards the hole in the
edge of 8.
Put drop of glue Hinto the
2 holes of 8.
Put dowels Finto the
holes of 8.
Screw expando dowel D
into right drawer side 7.
Note: Insert expando
dowel Das far as shown.
Do not over tighten.
Insert large locking nuts B
into right drawer side 7.
Make sure the ‘arrow’ on
locking nuts Bpoints
towards the hole in the
edge of 7.
Put drop of glue Hinto the
2 holes of 8.
Put dowels Finto the
holes of 7.
Screw expando dowel D
into drawer front 1.
Screw 24mm locking
screw Ainto front 1.
Note: Insert 24mm locking
screw Aand expando
dowel Das far as shown.
Do not over tighten.
Put drop of glue Hinto the
4 holes of 1.
Put dowels Finto the
holes of 1.
D
1
D
D
F
A
F
A
F
A
F
A
A
HF
1

4
E
E
E
E
EE
E
E
E
4
Assembly Instructions
Step - 12
Step - 13
8
Step - 11
Finished
edge
H
I
C
C
I
C
C
I
C
C
I
C
C
I
C
C
3mm
3mm
I
309mm
130mm
3
8
3
7
Attaching drawer panels
Put drop of glue Hinto the
8 holes of drawer back 3.
Position the 4 dowels F
of drawer side 7and 8
onto the holes of drawer
back 3.
Insert expando housing E
into drawer base 4.
Make sure that the
expando housing Eis
open.
Position the wheel I
on the drawer base 4.
Make sure that there is
enough free space to the
edges of drawer base 4.
use 2 chipboardscrews C
to mount each wheel Ion
drawer base 4.

Assembly Instructions
Step - 15
9
Step - 14
1
3
8
7
H7
8
1
3
8
7
4
Attaching drawer base
slide drawer base 4
into the drawer from the
top until till the 8
expando dowels Dare
totally in the expando
housing Eof drawer base
4.
Attaching drawer panels
Put drop of glue Hinto the
4 holes of drawer side 7
and 8.
Position the 4 dowels F
of drawer side 7and 8
onto the holes of drawer
back 3.
Use a screwdriver to turn
locking nuts clockwise to
lock.