Argos 237/9430 User manual

Two Drawer TV Unit
Dimensions
Width - 100cm
Depth - 40cm
Height - 45cm
Issue 1 - 10/04/14
Important –Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Assembly Instructions- Please keep for future reference 237/9430

Safety and Care Advice
Important– Please read these instructions fully before starting assembly
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Check you have all the
components and tools listed on
pages 2 and 3.
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Care and maintenance
1
• Parts of the assembly will be
easier with 2 people.

Components - Panels
Please check you have all the panels listed below
2
Shelf (918 x 362mm)
1
Front rail (918 x 80mm)
5Rear rail (918 x 80mm)
6
Left side panel
(435 x 368mm)
7Right side panel
(435 x 368mm)
8Top panel (1000 x 400mm)
9
Support panel
(160 x 70mm)
2Divider
(347 x 195mm)
3Foot
(36 x 36mm)
4
Back panel
(924 x 223mm)
10 Drawer left side
panel x 2
(300 x 125mm)
11
Drawer back
panel x 2
(397 x 125mm)
13 Drawer base x 2
(407 x 297mm)
14 Left drawer front
(444 x 207mm)
15 Right drawer front
(444 x 207mm)
16
Drawer right side
panel x 2
(300 x 125mm)
12
Note: Holes are nearer to edge.

3
12mm Screw x 37
Ruler- Use this ruler to help correctly identifythescrews
Tools required
A
Runner outer piece x 4Runner inner piece x 4
Bolt x 2
E
Metal dowel x 23 Wood dowel x 20
B
H
C
I
Note:The quantities beloware the correct amount to complete the assembly. In some cases more
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
110 115 120 125 130 135 140 145 150 155 160 165 170
105
F
35mm Screw x 14
D
Large metal
cam x 15
Small metal
cam x 8 Handle x 2
G
J
Components - FittingsIf you have damaged or missing components,
call the Customer Helpline: 08456 400800
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)

4
Assembly Instructions
Step 1
Dis-assemble Runners
Screw Support panel
to Shelf using
2 Screws as shown.
G
G
2
2
1
Step 2
1
A
B
To disassemble the
runners pull out the inner
piece of runners, to
seperate the Inner piece
and the Outer piece
, push and hold the
tab and then pull
completely out as shown.
A
B

5
Assembly Instructions
D
D
1
1
3
3
3
Note: Insert metal
dowels as far as shown.
Do not over tighten.
as shown.
Screw metal dowels
into Shelf
Firmly push wood
dowels into indicated
holes.
Step 3
Step 4
D
Make sure the front end
of Runner is flush with
the front edge of Divider.
C
B
B
C
E
E
Make sure the front end
of Runner is flush with
the front edge of Divider.
Position Runner outer
piece onto Divider
and fix through the
indicated holes
shown using Screws .
Turn over the Divider.
Note: Make sure the front
end of Runner is flush
with the front edge of
Divider.
B
C
3
Step 5
Position Runner outer
piece onto Divider
and fix through the
indicated holes
shown using Screws .
Note: Make sure the front
end of Runner is flush with
the front edge of Divider.
B
C

Firmly push Divider
onto Shelf , make
sure the wood and metal
dowels enter
corresponding holes.
G
1
1
4
4
5
5
3
3
Assembly Instructions
6
Step 7
Step 6
Long leg.
Taped edge
face upwards.
Note: Tighten all cams
in this way.
Note: Longer
leg of the cross
on the Metal
Cams must face towards
end of panel (as shown).
Then, using a Philips
Screwdriver, screw all
Metal Cams clockwise
until they are ‘hand tight’.
F
F
Screw Foot to Front
rail using 2 Screws
as shown.
G
Insert Large metal
Cams into the holes
on Divider so that they
are flush.
F

1
3
7
5
6
7
Assembly Instructions
Step 8
Position Runner outer
piece B onto Left side
panel and fix
through the indicated
holes shown using
Screws .
A
C
7
Step 9
Note: Rubber tube on
the runner should face
to the back panel groove
as shown.
Note: Cut out on the
corner of rails should
face outwards as
shown.
B
C
Secure with Screws .
G
G
G
Cut out on the corner
of rails should face
outwards as shown.
Rubber tube on the runner
should face to the back
panel groove as shown.
E
E
Firmly push wood
dowels into the
indicated holes in
Divider .
E
Firmly push Front and
Rear rails onto
the dowels on Divider,
make sure the dowels
enter corresponding
holes.
3
56

D
1
1
1
7
7
7
7
8
8
Firmly push Left side
panel onto the end
of Shelf , Front
and Rear rails ,
make sure the wood and
metal dowels enter
corresponding holes.
Assembly Instructions
8
Step 10
Step 11
D
Screw metal dowels
into Left side panel
as shown.
Firmly push wood
dowels into indicated
holes.
E
E
F
F
F
Secure with Cams .
Lift the end of panels a
little to easily fitting dowels
into corresponding holes.
5
6
5
5
6
6
Step 12
Repeat Steps 9 to 11 to
assemble Right side
panel as shown.
Two people may be
needed here.
Stand unit upright.

into Top panel
as shown.
7
8
9
9
9
9
Assembly Instructions
Step 13
D
D
Screw metal dowels
Firmly push wood
Turn over the Top panel.
dowels into indicated
holes.
E
Firmly push Top panel
onto Side panels
and support panel ,
make sure the wood and
metal dowels enter
corresponding holes.
Secure with Metal
cams .
F
F
Step 14
2
2
E
9
7 8
Two people may be
needed here.