Argos 608/0811 User manual

MADE IN
BRITAIN
Dimensions
Width - 100cm
Depth - 59cm
Height - 89.5cm
Athina - 1000 Base Unit
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 3 - 01/02/12
Important - Please read these instructions fully before starting assembly
608/0811
608/0938
608/0873
608/2981
608/0990
ALR2458
25/03/11: Added Argos Code 608/2981
01/02/12:
Rail changed to D0325A.
Plinth changed to D0326A.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 42kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• Parts of the assembly will be
easier with 2 people.
Glue Safety - Take care when using glue, please follow the advice below
Skin contact: Remove contami-
nation by washing with soap and
water. This procedure should be
followed prior to aeting and
drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
brackets supplied.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
1
80%
x 2
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Door (D0317A)
(716 x 497mm) x 2
2
9
Base (D0323A)
(970 X 499mm)
Shelf (D0324A)
(969 X 427mm)
Top (D0339A)
(1000 x 590mm)
Back (X740)
(980 x 533mm)
3
4 5
6 7
8
10
Left Side (D0315B)
(870 X 570mm)
Right Side (D0316B)
(870 x 570mm)
Rail (D0325A)
(970 x 60mm) x 2
Plinth (D0326A)
(970 x 150mm)
Munting (D0327A)
(689 x 59mm)

Please check you have all the fittings listed below
Tools required
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 14
B
Metal dowel (F901) x 10
C
D
Shelf support (F110) x 4
E F
G H I
Rule Scissors Hammer Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Nail (F51) x 14
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J
Door Buffer (F137) x 4
L
Electric drill
Large locking
nut (F900) x 10
Bracket (F945) x 4
25mm Screw (F50) x 4
J
13mm Screw (F79) x 1
K
13mm Screw (F63) x 813mm Screw (F79) x 6
K
Hinge Plate
(F853) x 4 Hinge (F852) x 4
MHandle (F847a ) x 2
aMHandle Screw (F847b) x 4
b N
40mm Screw (F910) x 2

Front
edge
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
B
B
B
B
B
B
1
1
1
K
K
K
Front
edge
Step 2
a:
b:
K
Prepare the left side
a: Fit 2 hinge plates
onto the left side ,
making sure that the slot
is facing towards the
front edge.
b: Screw 5 metal
dowels into the holes
shown on the left side
. .
Note: Tighten metal
dowels up fully against
the panels.
1
B
1
Fit 2 brackets to the
left side
Fit a bracket to the
left side , 100mm in
from the back edge, see
diagram.
Fit another bracket to
the left side , 100mm
down from the top edge,
see diagram.
Secure each bracket
using screw .
Note: The brackets must
be flush with the edges
of the panel.
1
F
F
H
1
100mm
100mm
F
F
F
H
F
H

Assembly Instructions
5
Step 3
Step 4
B
B
B
B
B
2
2
Front
edge
K
K
2
K
K
Prepare the right side
a: Fit 2 hinge plates
onto the right side ,
making sure that the slot
is facing towards the
front edge.
b: Screw 5 metal
dowels into the holes
shown on the right side
. .
Note: Tighten metal
dowels up fully against
the panels.
2
B
2
100mm
100mm
FF
HH
Fit 2 brackets to the
right side
Fit a bracket to the
right side , 100mm
down from the back
edge, see diagram.
Fit another bracket to
the right side ,
100mm down from the
top edge, see diagram.
Secure each bracket
using screw .
Note: The brackets must
be flush with the edges
of the panel.
2
F
F
H
2F
F
Front
edge

Assembly Instructions
6
Prepare the base
Insert 4 large locking
nuts into the base
as shown.
Note: Arrow on locking
nut must point towards
hole in edge of panel.
Tap 6 wooden dowels
into the base as
shown.
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Step 5
Step 6
C
C4
Fit the base to the
right side
Push the base onto
the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the base .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
4
2
C
4
C
10mm
A
A
4A
A
A
C
C
A
A
A
C
C
4
Finished
front edge
B
4
C
2

Assembly Instructions
7
Step 7
Step 8
Fit a rail to the right
side
Push one of the rails
onto the right side as
shown.
Use a screwdriver to
tighten the large locking
nut .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
6
2
C
C
A
C
C
A
6
Prepare the 2 rails
and munting
Insert 2 large locking
nuts and 2 wooden
dowels into each of
the 2 rails .
Tap 2 wooden dowels
into the munting .
C
6
8
A
A
8
A
A
2
6

Assembly Instructions
8
Step 9
A
A
C
C
7
Prepare the plinth
Insert 2 large locking
nuts and 2 wooden
dowels into the plinth
. .
C
7
A
Fit the munting
Fit the munting to the
rail and base and
secure using 2 screws
. .
8
N
6 4
Step 10
N
8
N
6
4

Polystyrene
block
Assembly Instructions
Use 2nd hole in from front of
Runner F1004 to fit 1st F73 then
fit other F73 to match other hole.
Rebated Edge
F73
COVERED EDGE
Use 2nd hole in from front of
Runner F1004 to fit 1st F73 then
fit other F73 to match other hole.
F1004
When you insert F900,
make sure the arrow is
pointing towards the hole
in the edge of the panel.
F900
F73
F1004
COVERED EDGE
9
Step 11
Step 12
Step 7
Fit the top
Note: To make it easier
to fit the top panel, place
polystyrene blocks from
the packaging
underneath the side
panels to raise the
assembly.
Position the top onto the
unit, making sure that
the back edge of the top
is flush with the back
edge of the sides.
Secure the top using
screw through the 2
brackets fitted at the top
edge of the side panels.
H
F100mm
100mm
500mm
F
HH
H
3
6
Fit the rail and plinth
Push the rail and
plinth onto the right
side as shown.
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the 2 panels, as shown.
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
Note: Support the rail
. until the left side has
been fitted in the next
stage.
7
2
C
C
6
Fit the left side
Push the left side
onto the assembly.
Use a screwdriver to
tighten the 5 large
locking nuts fitted to
the base , rails
and plinth .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
6
7
1
4
C
C
26
7
6
6
6
7
4
1