Argos Vince 697/1470 User manual

Step 7
Vince – Storage Bed Frame
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Assembly Instructions - Please keep for future reference
Important - Please read these instructions fully before starting assembly
Dimensions
Width x Depth x Height
213cm x 148cm x 33.5/111cm (Double)
223cm x 163cm x 33.5/111cm (King)
697/1470
697/1487

Safety and Care Advice
Important–Please read these instructions fullybefore starting assembly
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals away
from the work area, small parts if
swallowed could cause choking.
• Make sure you have enough
space to layout the parts before
starting.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Assembly requires 2 people.
• Do not fully tighten bolts until
the whole bed is assembled.
• Do not overtighten the nuts to
avoid causing damage to the
threads.
• We do not
recommend the
use of power
drill/drivers for
inserting bolts,
or screws as this could damage
the unit. Only use hand screw-
drivers and Allen keys.
• Dispose of all packaging
carefully and responsibly.
.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
stunrostlobesooloneraereht
. .tinusihtno
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
1
Caution
• Please ensure children and
pets do not play in the storage
area or try to lift up the metal
frame.
• Once assembled, put mattress
on frame before pushing it down
and only lift up or push down the
metal frame with mattress on top.
• Only use the handle to lift
and lower the bed frame to
avoid trapping fingers.

Components If you have damaged or missing components,
call the Customer Helpline: 08456 400800
2
1 Right side rail
2 Left side rail
3 Headboard
7 Footboard8 Horizontal support rail
9 Slat frame
5 Corner brackets x 4
4 Non-woven fabric x 1
10 Slat caps x 52 (double)
or x 60 (king & s-king)
11 Slats x 26 (double)
or x 30 (king & s-king)
Please check you have all the parts listed below
6 Wooden rail x 1

Components - Fittings
3
Please check you have all the fittings listed below
Tools required
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
A
40mm M8 Bolt x 8
5mm Allen key x 1 (supplied) 4mm Allen key x 1 (supplied)
B
35mm M6 Bolt x 16
C
D E
H
45mm M6 Bolt x 4
I
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
F
G
J
Spanner x 1 (supplied)
60mm M6 Bolt x 2 Nut x 2 (Big) 75mm M6 Bolt x 2
Nut x 6 (Small) Flat washer x 8 M6 Flat washer x 26
Spring washer x 8

Assembly Instructions
4
Step 1
Fix the wooden rail
to the footboard
using 2 bolts , flat
washers and using
the Allen key provided.
a:
b:
6
7
D
I
Step 2
a: Fix the side rail ＆
to the headboard
using bolts , spring
washers , flat washers
as shown.
A
J
H
1
2 3
b: Fix the side rail ＆
to the footboard
using bolts , spring
washers , flat washers
as shown.
A
J
H
1
2 7
7
6
I
D6
7
3
1
2
HJA
3
1
7
2
1
H
J
A7
1

Assembly Instructions
Step 3
5
Step 4
Fix the corner brackets
using bolts , and
flat washers as shown.
5
B
I
Fix the slat frame to
the lift up mechanisms
using bolts , flat
washers and nuts
as shown.
9
C
IG
Repeat step on all
corners.
Repeat step on the
other side.
5
IB
C
I
G
9
5
9

Assembly Instructions
Step 5
Step 6
6
Insert nut to lift up
mechanisms as shown.
F
Fix the slat frame
and horizontal support
rail to the lift up
mechanisms using bolts
, flat washers and
nuts as shown.
9
8
EI
G
Repeat step on the
other side. F
8
9
E
I
G
I
9
8

Assembly Instructions
Step 7
7
Step 8
Slot the slats to the
slat caps then place
it to the slat frame
as as shown.
11
10
9
Place the non-woven
fabric on the bottom
of the bed as shown.
4
10
11
4
Assembly is complete.
9
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Assembly Instructions
8
• Position the mattress on the slat frame whilst it is in the
closed position.
• Initially it might appear that the gas
lifts are very stiff when opening and
closing the ottoman, this is normal.
Ottoman operating instructions
• Operate the handle to open and close the ottoman.
Note – it takes a lot of force to make the initial movement
of the ottoman, the nearer to being closed the ottoman is,
the easier it is to move. When the ottoman is almost shut
it will close completely under its own weight.
• After operating the ottoman a few
times, the movement of the gas lifts
and the opening and closing of the
ottoman will become easier.
• Only the handle is used when
lifting and lowering the frame,
failure to comply with this
warning may result in injury
and finger entrapment.
• The metal frame is fully raised
in the “UP” position before using
the ottoman space, otherwise
the frame could fall causing injury.
• Please keep children
and pets away from the
ottoman bedstead whilst
opening and closing the
slat frame to avoid injury.
Warning