Argos Retro 226/2877 User manual

MADE IN
BRITAIN
Dimensions
Width - 60cm
Depth - 40cm
Height - 117cm
Retro - Tall Drawer Unit
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 27/06/14
Important - Please read these instructions fully before starting assembly
ALR3066
226/2877

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 37kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 1, 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
12
3 4 5
6 7 8
Large Drawer Back (W513-124)
(513 x 124mm) x 3
Large Drawer Base (T522-367)
(522 x 367mm) x 3
Medium Drawer Back (W276-124)
(276 x 124mm) x 2
Small Drawer Back (W168-124)
(168 x 124mm) x 2
Medium Drawer Base (T287-367)
(287 x 367mm) x 2
Small Drawer Base (T179-367)
(179 x 367mm) x 2
Left Drawer Side (W370-124LH)
(370 x 124mm) x 7
Right Drawer Side (W370-124RH)
(370 x 124mm) x 7

Components - Panels
Please check you have all the panels listed below
9
80%
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Left Side (DF443)
(1154 x 394mm)
10 Right Side (DF444)
(1154 x 394mm)
12
13
Shaped Rail (DF449)
(563 x 74mm)
Cross Rail (DF447)
(563 x 94mm) x 6
Divider (DF448)
(198 x 392mm) x 2
11
14 1615
17 18 19
20
Top (DF445)
(597 x 396mm)
Back (X1076-589)
(1076 x 589mm)
Large Drawer Front (D3028A)
(557 x 192mm) x 1
Medium Drawer Front (D3029A)
(322 x 192mm) x 1
Small Drawer Front (DF451)
(214 x 192mm) x 2
Large Drawer Front (DF446)
(557 x 192mm) x 2
Medium Drawer Front (DF450)
(322 x 192mm) x 1

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A B C
D E
G H I
Nail (F51) x 18
JL
O
Wedgefix (F639) x 14
13mm Screw (F63) x 42
MR Runner (F160) x 7
b
L Runner (F161) x 7
Mc
L Runner (F159) x 7
Ma
R Runner (F162) x 7
Md
350mm long
Metal dowel (F901) x 34 Large locking
nut (F900) x 20
Small locking
nut (F3) x 14
13mm Screw (F79) x 1
K
S
N
Knock-in Peg (F171GY) x 28
F
25mm Screw (F50) x 2
Wooden dowel (F22) x 20 19mm Screw (F461) x 10
Plastic Nail (F91) x 4
Handle (F220) x 2
P R
Handle (F287) x 1
T
Handle (F278) x 1
Q
Handle (F319) x 1
Handle (F123) x 1
Handle (F266) x 1
U
Bracket (F327) x 1
9mm Screw (F73) x 42

Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
x 2
x 2
x 2
A
C
CC
12
Step 2
Prepare the 2 small
drawer fronts
Screw 2 metal dowels
into each of the small
drawer fronts .
Note: Tighten the metal
dowels up fully against
the panels.
A
19
Prepare 2 sets of
drawer sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
C
1
2
A
A
19
Tools required
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Electric drill
(do not use for
fitting screws)
Short cross-head
screwdriver
80%

Assembly Instructions
5
Step 3
K
K
Fit the small drawer
bases
Slide the small drawer
base down the
grooves in the drawer
sides and and
down into the groove in
the small drawer front .
Step 5
Fit the small drawer
backs
Fit the small drawer back
. between the drawer
sides and .
Make sure that the small
drawer base fits into
the groove in the small
drawer back .
Hold the small drawer
back in position and
tap the knock-in pegs
through the holes in the
drawer sides and .
8
1 2
19
5
1 2
8
5
5
K
1 2
x 2
x 2
K
K
8
1
5
1
2
8
2
19
19
x 2
B
A
C
Attach the drawer
sides to the small
drawer fronts
Push the left drawer sides
. and right drawer sides
. onto the back of the
small drawer fronts .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
1
2
19
C
C
1
2
2
1
Step 4

Assembly Instructions
6
Step 6
Attach the handles
Attach a handle to
each of the small drawer
fronts using screw .
P
F
19
Step 7
Fit the wedgefixes
Turn the drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
J
x 2
x 2
J
F
P
19
x 2
x 2
x 2
A
C
CC
12
Step 9
Prepare the 2 medium
drawer fronts
Screw 2 metal dowels
into each of the medium
drawer fronts and .
Note: Tighten the metal
dowels up fully against
the panels.
A
17 18
Prepare 2 sets of
drawer sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
C
1
2
A
A
17 18
Step 8
J
J

Assembly Instructions
7
Step 10
K
K
Fit the medium
drawer bases
Slide the medium drawer
base down the
grooves in the drawer
sides and and
down into the groove in
the medium drawer front
. and .
Step 12
Fit the medium
drawer backs
Fit the medium drawer
back between the
drawer sides and .
Make sure that the
medium drawer base
fits into the groove in the
medium drawer back .
Hold the medium drawer
back in position and
tap the knock-in pegs
through the holes in the
drawer sides and .
7
1 2
4
1 2
7
4
4
K
1 2
x 2
x 2
K
K
7
1
4
1
2
7
2
17 18
17 18
x 2
B
A
C
Attach the drawer
sides to the medium
drawer fronts
Push the left drawer sides
. and right drawer sides
. onto the back of the
medium drawer fronts
and .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
1
2
17
18
C
C
1
2
2
1
17 18
Step 11

Assembly Instructions
8
Step 13
x 3
A
Prepare the 3 large
drawer fronts
Screw 2 metal dowels
into each of the large
drawer fronts and .
Note: Tighten the metal
dowels up fully against
the panels.
A
13 16
A
A
13 16
Step 6
Attach the handles
Attach handle to a
medium drawer front
using screws .
Attach handle to the
medium drawer front
using screws .
Q
E
Step 14
Fit the wedgefixes
Turn the medium drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
Step 15
J
x 2
J
J
J
17
18
E
E
Q
F
F
R
17
R
F
18

Assembly Instructions
9
Step 16
15 16
Fit the large drawer
bases
Slide the large drawer
base down the
grooves in the drawer
sides and and
down into the groove in
the large drawer front
. and .
6
1 2
x 3
6
1
2
15 16
15 16
x 3
x 3
x 3
B
A
C
C
CC
12
Prepare 3 sets of
drawer sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 17
C
1
2
Attach the drawer
sides to the large
drawer fronts
Push the left drawer sides
. and right drawer sides
. onto the back of the
large drawer fronts
and .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
Step 18
1
2
15
16
C
C
1
2
2
1