Argos HOME Jenson Gloss 341/1304 User manual

Spare Parts
Visit: www.argos-support.co.uk
Email: [email protected]
Call: 0330 016 1114
Customer Support
Call: 0345 640 2020
Jenson
Gloss
Issue 1 - 04/12/19
341/1304 310/4642
CR
CR

Safety
Important - Please read these instructions fully before starting assembly
Care Advice
• Check you have all the
components and tools listed on
relevant pages.
• Remove all fittings from the
specified plastic bag and
separate them into their groups.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• Assembly videos are
available throughout
these instructions by
scanning in the QR
codes.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean with a damp cloth.
• Warning: This unit weighs
approximately 17kgs.
Please lift with care.
• Assembly to be carried out by
a competent adult only.
• During assembly children
should be kept away from the
product due to possible risk of
injury.
• Installation shall only be
carried out exactly according to
the manufacturer’s instructions -
otherwise a safety risk can
occur if incorrectly installed.
• Do not use this item if any
components are missing or
damaged.
• Regularly check all fastenings
to ensure they are properly
tightened.
• WARNING: To prevent
possible overbalancing this unit
must be secured to a wall using
the overbalance protector kit
supplied.
• A unit that is allowed to topple
can cause serious or fatal injury.
In addition to wall fixing the unit,
do not put any heavy objects on
top of the unit and never allow
children to climb or hang on
drawers, doors or shelves.
• Refer to guide after section 19
for wall fixing information.
CR
CR
CR
CR

Cabinet Panels
Drawer Panels Note: the internal drawer panels are grey
171.8 x 38.8cm
DF-00020476
271.8 x 38.8cm
DF-00020477
DF-00020479
WRP-00000303 WRP-00000304
310 x 35.3cm
DF-00019975
490.7 x 9.2cm
DF-00019974
598.3 x 39.1cm
DF-00020475
690.7 x 36.6cm
DF-00019973
790.15 x 10.8cm 835 x 6.8cm x2935 x 6.8cm x2
TDF-00019982
10 40.8 x 34.1cm x2
WRP-00000348
11 39.7 x 6.8cm x2

Fittings Use these drawings to
correctly identify the fittings
Bag 1
A
F901
F22
Ax 8 Cx 8 E
F73
x 12
D
F171GY
Bag 2
Mx 8 Kx 8
A
F901
Ax 4 J
F639
x 8
Bx 8
F900
F910
x 2
F607
Lx 4
Fx 8
F63
M
F464
x 6
F892 F893
Hx 4 Gx 4 Fx 4
F63
F269
Ix 1

Fittings
F422F424
F425F426
DL
DR
CL
CR
ax 2
bx 2
cx 2
d
N
N
N
Nx 2
Tools
Only used for
drilling walls

1
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
Fixing Bottom Mounted Runners
Ex 6
CL
CR
ax 1 bx 1 NN
Bag 1
A
F901
F22
Ax 8 Cx 8 E
F73
x 12
DB x 8
F900
F910
x 2
F892 F893
Hx 4 Gx 4 Fx 4
F63
F269
Ix 1
CL
CL
CR
CR
CL
aN
bN
1
2
CR

2
3
Ax 6
1
2
Screw directly
into panel as
illustrated
Fx 2
CR
CL
1
2
CR
CL
Screw directly
into panel as
illustrated

1
2
CR
CL
4
Hx 4
5
Gx 4
5
5
6
Ax 2

Finished
front edge
CR
7
Nbx 1
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
Fixing Bottom Mounted Runners
CR
Fx 1
Ex 3
8
Cx 2 Bx 2
9Turn the panel
over for the
next step
CR
Screw directly
into panel as
illustrated
B
3
Finished
front edge
Finished
front edge
Finished
front edge
Finished
front edge
CR
A
CR
CRCR
3
Finished
front edge
Finished
front edge
CR
3
3
Finished
front edge
Finished
front edge
3

A
10
Nax 1
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
Fixing Bottom Mounted Runners
CL
Fx 1
Ex 3
B
Finished
front edge
CL
3
Finished
front edge
3
CL
CL
CL
Finished
front edge
11
5
CR
x 2
3

Finished
front edge
Finished
bottom edge
Finished
front edge
Finished
front edge
CR
12
13
Cx 4 Bx 4
14
Cx 2 Bx 2
6
CR
4
5
2

Finished
front edge
CR
CR
CR
15
CR
4
16
x 1
x 2
6

17
CR
CR
CR
CR
x 2
18
Dx 2
1

CR
CR
19 WARNING!
In order to prevent overturning
this product must be used with the
wall attachment device provided
See the next section for a guide
to wall mounting and fixings
CR
CR
Ix 1
To prevent possible overbalancing this unit must be secured to a suitable wall by fitting of
the overbalance protector kit to the unit.
Wall fixings are not supplied as they will need to suit the wall type.
Note: Take care when drilling the wall that you do not drill into any pipes, wires etc.
If in doubt, consult an expert.
Washer
Screw
Washer
Screw
(not supplied)
Wall fixing
(not supplied)
Modesty Panel
Example

Important note:
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
If plastic wall plugs
are supplied with your
product:
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
using incorrect fixings is the
responsibility of the installer.
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualified
tradesperson if you are unsure.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5: Ensure wall plugs are well fitted and are a tight fit in the
drilled hole.
Types of walls You can use one of the following types of wall plug if your
walls are made of brick, breeze block, concrete, stone or wood.
Generally aerated blocks should not
be used to support heavy loads, use
a specialist fitting in this case. For light
loads, general purpose wall plugs can
be used.
For use with plasterboard partitions or
hollow wooden doors.
For use with walls stuck with
plasterboard. The hammer fixing allows
it to be fixed to the wall rather than the
plasterboard. Always check the fixing
is secure to the retaining wall.
For use when attaching light loads on
to plasterboard partitions.
For use when fitting or supporting
heavy loads such as shelving, wall
cabinets and coat racks.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
No.1 “General Purpose” wall plug No.3 “Cavity Fixing” wall plug No.5 “Hammer Fixing” wall plug
No.2 “Plasterboard” wall plug
No.4 “Cavity Fixing-Heavy Duty”
wall plug
No.6 “Shield Anchor” wall plug
Heavy loads
A Guide to Wall Mounting & Fixings
Care &
Maintenance
Safety: Always check the fitting
and location to ensure your safety
in and around the home.
Fitting: From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.

Drawer Assembly
Bag 2
20
9
Lx 4
8
21
Kx 4
8
11
x 2 x 2
x 2
F171GY
Mx 8 Kx 8
A
F901
Ax 4 J
F639
x 8
F607
Lx 4
Fx 8
F63
M
F464
x 6

22
23
Kx 4
9
10
24
Ax 4
x 2
x 2
7

26 x 4
27 Ensure the drawer bases
sit flush by turning the
shelf studs clockwise or
anti-clockwise
25
Mx 6
8
9
7
7
8
9

29
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
Fixing Bottom Mounted Runners
Fx 4
DL
DR
cx 1
d
N
Nx 1
28
Jx 8
DL
DR
Screw directly into
Drawer Side as illustrated
DL
DL

30
Fx 4
DL
DR
cx 1
d
N
Nx 1
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
Fixing Bottom Mounted Runners
DL
DL
DR
Screw directly into
Drawer Side as illustrated
DL
DL