Argos Nordic 1441572 User manual

Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Assembly Instructions - Please keep for future reference
1441572
Nordic - 2 Door Wardrobe
03456 400 800
02-06-2014
Dimensions
idth : 81.1 cm
Depth : 49,0 cm
Height : 191,3 cm
344101022

Important - Please read these instructions fully before starting assembly
Safety and Care Advice
• Check you have all the
components and tools listed on
pages 3 and 4.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• ake sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• We do not recommend the use
of power drill/drivers for
inserting screws, as this could
damage the unit. Only use hand
screwdrivers.
• Dispose of all packaging
carefully and responsibly .
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• From time to time check that
there are no loose screws on
this unit.
• Only clean using a damp cloth
and mild detergent, do not use
bleach or abrasive cleaners.°
Care and maintenance
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
2

Top/Bottom x2
V155864
781x470x15 mm
Top rail
V155806
792x80x15 mm
Plinth, front
V155803
793x96x15 mm
Door rail x4
V155827
316x25x15 mm
Plinth, ba k
P155866
781x60x15 mm
Hanging rail
L220053 - 771
771x22x15 mm
Side, Right
V155837
1833x475x15 mm
Side, Left
V155841
1833x475x15 mm
Door x2
V155822
1725x395x15 mm
Ba k x2
NM415853
1741x397x3 mm
H-profile
B81700 - 1700
4x1700 mm
Please check you have all the panels listed below
Components - Panels
3
If you have damaged or missing components, call
the Argos Customer Helpline: 03456 400 800
3
4
5
6
10
16
12
87
15

BA10240
ø6,1x11,5 mm s rew x8
BA10801
20x20x2 angle x4
BA 10170
ø4,0x35 mm s rew x2
BA10468
ø40x30 mm Wooden knob x2
BA10590
ø15x9,5 mm am x14
BA10603
ø5/11x34 mm bolt x14
BA1039 0
ø8x30 mm wooden dowel x10
BA10731
15x22 mm support for hanger x2
BA10050
ø3,5x15 mm s rew x22
BA10715-1
ø10x8 mm magnet x4
BA10715-2
ø10x8 mm magnet at h x4
BA10815
50x50x2 mm angle x2
BA10025
ø1,2x20 mm nail x50
BA10508
ø26 up hinge x6
BA1053 2
0 mm/37 mm rossplate x6
BA10130
ø4,0x35 mm s rew x12
BA182002
wallstrap and instru tion
Ba10688
500x250x Nail holder x1
Please check you have all the panels listed below
Components - Fittings
If you have damaged or missing components, call
the Argos Customer Helpline: 0845 640 30 30
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
Tools required
Ruler - se this ruler to help correctly identify the screws
A G O
R T L
J
i
D
NMC
E
4
PQY
W

Assembly Instructions
Knock down the Dowels
A into the holes
indicated on top/bottom
3 and the back plinth 4
using a small hammer.
Press the magnets M
into holes indicated.
Step 1
Step 2
Fix the support for
hanger rail L to the
sides 1 and 2 using
screws T.
Fix the crossplates P to
the sides 1 and 2 using
the premounted screws.
See details.
position the crossplate
exactly as shown.
Screw the olts D into
the holes indicated.
Fix the angles V to the
sides1 and 2 using
screws E. Place the
angles as shown.
See details.
5
4
A
A
x2
3
A
A
A
A
M
M
M
M
L
L
T
T
T
L
1
2
P
P
P
P
P
P
E
E
E
E
P
D
D
D
D
D
D
D
D
D
D
D
D
D
D

Assembly Instructions
Place the sides 1 and 2
onto the top 3, the back
plinth 4 and the bottom
3.
Push cams into holes
indicated, arrows
pointing towards sides.
Turn the cams C to the
right to fix the top and
bottom 3 and the back
plinth 4.
See details.
Step 3
Step 4
6
Fix the front plinth 5
onto the angles V using
screws E.
1
2
3
3
4
C
C
C
C
C
C
C
C
C
C
E
E
EE
1
1
5
5
2
3
4

Assembly Instructions
Place the backs 7 into
rebates in the sides 1,2
and into the H-profile 15.
Step 5
Step 6
Step 7
Place the cup hinges Q
into the holes indicated
on the doors 8.
Fix the hinge Q using
screws T.
Place the magnet
catches N in the holes
indicated on doors 8,
using a small hammer.
Fix the door rails 16 to
the doors 8 using screws
O.
7
!
Im portant!
Make sure the
angle etween
the top and the
sides is 90° when
the ack is
attached.
Fix the acks to the
sides 1,2, the top 3 and
the ack plinth 4, using
nails i.
Use the nail holder Yd
and a small hammer.
i
i
i
i
i
i
i
N
N
N
8
8
Q
Q
Q
Q
8
16
16
16
8
8
1
2
15
7
7
3
O
O
O
O
O
O
O
O
O
x2
x2
T T
TT
TT
T
T

Assembly Instructions
Place the top rail 6 onto
the top 3.
Fix the top rail to the
top using angles W and
screws T
Step 8
Step 9
8
Place the hanger rail 10
into the support L.
To fix the doors 8, slide
the cup hinges Q onto
the crossplates P.
Fix the hinges using the
pre-mounted screw in
the crossplates.
See details.
Fix the wooden knobs G
to the doors using
screws R.
W
WW
T
T
T
T
T
T
T
6
6
3
3
1
Tighten these s rews
L
10 10
L
P
P
Q
Q
Q
Q
Q
G
R
x2
8
8

Assembly Instructions
Its recommended that
the wardro e is fixed to
the wall.
Use the fittings J.
Follow the instruction
included with the
fittings.
Step 10
9
!
Warning!
The wardro e is
heavy. Lift with
care.
Wallstrap and instru tion

Assembly Instructions
If you need help or have damaged or missing parts, call the Customer Helpline:
03456 400 800
Home Retail Group - 489-499 Avebury Boulevard - Saxon Gate West - Central ilton Keynes K9 2NW
Adjusting the doors
left/right.
a:
To adjust the door
towards the left hand
side - turn the adjusting
screw to the right.
b:
To adjust the door
towards the right hand
side - turn the adjusting
screw to the left.
Adjusting the doors
forwards/bac wards.
a:
Loosen the fixing screw.
b:
Push the cup hinge/the
door forwards or
backwards to adjust.
c:
Tighten the fixing screws
of ALL the crossplates.
Adjusting the doors
up/down.
a:
Loosen the two
pre-mounted screws of
each crossplates, UT
ONLY as much as it will
allows the crossplates to
move up and down.
b:
Push the door up or down
to adjust.
c:
Tighten the pre-mounted
screws of ALL
crossplates.
Assembly is complete.
Step 11
10