Argos Stirling 331/3639 User manual

MADE IN
BRITAIN
Dimensions
Width - 105cm
Depth - 39cm
Height - 67cm
Stirling - Dressing Table and Stool
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 2 - 13/01/15
Important - Please read these instructions fully before starting assembly
ALR3110
331/3639
330/0446
Issue 2 - 13/01/15 - Fly End has been reduced in length to 637mm.
Helpline number changed to 03456 400800.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 30kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
123Modesty (D3013A)
(630 x 245mm)
Right Side (D3005A)
(572 x 352mm)
Left Side (D3012A)
(572 x 352mm)
4
Fly End (D3031B)
(637 x 352mm)
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
overbalance kit supplied.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
80%
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
5Base (D2993A)
(405 x 390mm)
Top (D3010A)
(1050 x 390mm)
6
Drawer Base (T324-347)
(324 x 347mm) x 3
Back (X598-372)
(598 x 372mm)
7
Small Drawer Front (D2994A)
(372 x 156mm) x 2
Large Drawer Front (D2995A)
(372 x 245mm)
Small Drawer
Back (W313-124)
(313 x 124mm) x 2
Large Drawer
Back (W313-195)
(313 x 195mm)
Small Left Drawer
Side (W350-124LH)
(350 x 124mm) x 2
Small Right Drawer
Side (W350-124RH)
(350 x 124mm) x 2
Large Left Drawer
Side (W350-195LH)
(350 x 195mm)
Large Right Drawer
Side (W350-195RH)
(350 x 195mm)
11
8 9 10
12 13 14
15 16
17 19
18 Seat Pad (FMANPAD)
(398 x 348mm)
20
Stool Side (D2225A)
(451 x 352mm) x 2
Stool Base (D2224A)
(400 x 348mm)
Stool Rail (D2226A)
(400 x 144mm) x 2

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 11
B
Metal dowel (F901) x 28
D
Large locking nut
(F900) x 22
E
Small locking nut
(F3) x 6
F
M
L
Nail (F51) x 11
H I
O
38mm Screw (F81) x 3
C
G
40mm Screw (F910) x 8
K
J
N
Knock-in Peg (F171) x 12
Q
Drawer runner (F1004) x 6
25mm Screw (F50) x 4
9mm Screw (F73) x 12 9mm Screw (F74) x 6
Wedgefix (F639) x 6 Plastic Nail (F91) x 6
Handle (F463) x 3
P
Foot (F340) x 4
Strap Screw Washer x 2
Overbalance protector kit (F269) x 1
Tools required
Rule Scissors Hammer Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Electric drill
(only use
when drilling
into walls)

Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
B
B
B
F
F
FF
89
Step 2
Prepare the large
drawer front
Screw 2 metal dowels
into the large drawer
front .
Note: Tighten the metal
dowels up fully against
the panels.
B
7
Prepare the large
drawer sides
Insert a small locking
nut into the hole
shown on the large left
drawer side and the
large right drawer side
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
F
8
9
Attach the large
drawer sides to the
large drawer front
Push the large left drawer
side and large right
drawer side onto the
back of the large drawer
front .
Turn the small locking
nuts on the large left
drawer side and large
right drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
8
9
7
F
F
9
8
B
B
7
7
8
9

Assembly Instructions
5
Step 4
M
M
8
Fit the drawer base
Slide the drawer base
down the grooves in the
large drawer sides
and and down into
the groove in the large
drawer front .
Step 5
Fit the large drawer
back
Fit the large drawer back
. between the large
drawer sides and .
Make sure that the
drawer base fits into
the groove in the large
drawer back .
Hold the large drawer
back in position and
tap the knock-in pegs
through the holes in the
large drawer sides
and .
15
8
9
7
10
8 9
15
10
10
M
8
9
9
8
15
7
8
9
10
15
8
M
M
Attach the handle
Attach a handle to the
large drawer front
using screw .
C
H
Step 6
7
H
C
7

Assembly Instructions
6
Step 7
Fit the wedgefixes
Turn the large drawer
assembly over and slide
2 wedgefixes into the
front and back grooves,
as shown, and tighten up
the screws.
NN
N
N
F
FF
12 13
Step 9
Step 8
B
Prepare the 2 small
drawer fronts
Screw 2 metal dowels
into each of the small
drawer fronts .
Note: Tighten the metal
dowels up fully against
the panels.
B
11
B
B
11
Prepare the 2 pair of
small drawer sides
Insert a small locking
nut into the hole
shown on the small left
drawer side and the
small right drawer side
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
F
12
13
x 2
x 2 x 2

11
Assembly Instructions
7
Step 10
B
B
F
12
13
M
M
Fit the drawer bases
Slide the drawer base
down the grooves in the
small drawer sides
and and down into
the groove in the small
drawer front .
Step 12
Fit the small drawer
backs
Fit the small drawer back
. between the small
drawer sides and .
Make sure that the small
drawer base fits into
the groove in the small
drawer back .
Hold the small drawer
back in position and
tap the knock-in pegs
through the holes in the
small drawer sides
and .
15
12
13
11
14
12 13
15
14
14
M
12
13
M
M
15
12
13
15
14
12
13
Step 11
Attach the small
drawer sides to the
small drawer frontS
Push the small left drawer
side and small right
drawer side onto the
back of the small drawer
front .
Turn the small locking
nuts on the small left
drawer side and
small right drawer side
. .
12
13
11
F
13
12
x 2
x 2
x 2
11

Assembly Instructions
8
Step 13
Step 14
H
C
Fit the wedgefixes
Turn the small drawer
assembly over and slide
2 wedgefixes into the
front and back grooves,
as shown, and tighten up
the screws.
N
N
Attach the handle
Attach a handle to the
small drawer front
using screw .
C
H
11
N
N
11
x 2
x 2

A
Finished
front edge
Finished
front edge
Finished
front edge
Assembly Instructions
9
Step 15
Finished
front edge
K
P
a:
b:
c:
Prepare one surface
of the left side
a: Place 3 runners on
the left side . Slide
back the top of runner
and use the 2nd hole
from the front to fit the
1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the left side .
c: Tap 2 wooden
dowels into the left
side .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 2 large locking
nuts into the left side
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Turn the left side over for
the next step
1
K
K
E
1
P
P
1
1
E
A
10mm
A
K
P
K
K
K
K
P
K
P
E
E
A
1
1
1