Argos 603/1822 User manual

Width - 45cm
Depth - 51cm
Height - 94cm
Important– Please read these instructions fully before starting assembly
Customer Helpline: 08456 400800
Dimensions
Issue 1 - 9/02/10
Cross Back Chair
If you need help or have damaged or missing parts, call the
7
c:
d:
c:
After the sitting test,
re - tighten bolts again,
if any adjustment needed.
d:
It is highly recommend
to re - tighten all the bolts
again after using the chair
for 7 days.
Note : Please keep the
allen key to re - tighten
all bolts again when
required.
Assembly Instructions
If you need help or have damaged or missing parts, call the Customer Helpline: 0845 6400800
Assembly is complete.
603/1822
Assembly Instructions -Please keep for future reference
603/3837
603/3820

Safety and Care Advice
Important– Please read these instructions fullybefore starting assembly
Care and maintenance
1
• Check you have all the
components and tools listed on
page 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product during assembly,
this could cause damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
• Maximum safe weight of
user: 110 Kgs.
Step 2
e:
Assembly Instructions
Attach lock seats
by using screw as
shown in the figure.
E
De:
a:
Tighten all bolts.
Note : Stand the chair on
a level floor.
a: b:
b:
Sit on the chair to
the legs.
6
D
Pre-drilled
hole
Note : Step 2 is essential
to prevent the chair from
wobbling due to legs
uneven.
E

2
Components- Parts
Please checkyou have all the parts listed below
Chair back x 1 Seat x 1
If you have damaged or missing components,
call the
Customer Helpline: 08456 400800
12
Fron leg frame x 1
3
4Side rail x 2 (L,R)
5
c:
Assembly Instructions
d:
d:
c:
Stand the chair on a
floor. Insert bolts with
spring washers and
washers through side
rails holes into front leg
frame screw all bolts
by using ball allenkey .
3
A
F
B
C
Right side rail
Left side rail
Place the seat pad
on the table. Put the
chair frame on top of the
seat back.
2
A
B
C
1
34
4
2
BACK BACK

AssemblyInstructions
Step 1
a:
4
A
a:
b:
Components- Fittings
Please checkyou have all the fittings listed below
Note :The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
Bolt x 8
B
Spring washer x 8
C
D
Washer x 8
F
Lock seat x 2 Ball allenkey x 1
A
E
Screw x 4
b:
Attach left and right
side rails onto the chair
back with bolt ,
spring washers and
washers by using ball
allenkey as shown in
the figure.
B
C
F
Do not fully tighten.
Fit the front leg frame
onto the side rails .
34
34
4
1
pre - drilled hole
Right side rail
Left side rail
BACK
A
B
C
4
4
4
1
BACK
3
4
41