Argos 033 3562 Series User manual

Assembly Instructions -Please keep for future reference
Width - 141cm
1 Drawer Low Plasma Unit
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08450613967
Please turn to back page for important information when contacting Customer Helpline.
Dimensions
Depth - 38.8cm
Height - 25cm
Rev A - 26/03/2013
033 xx 3562

Important - Please read these instructions fully before starting assembly
Safety and Care Advice
Check you have all the
components and tools listed on
pages 2 and 4.
Remove all fittings from the
plastic bags and seperate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Parts of the assembly will be
easier with 2 people.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Care and maintenance
Always lift furniture when
moving it (do not drag)
otherwise the joints may be
damaged.
From time to time check that
there are no loose screws on
this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
1
Dust surfaces with a soft, dry,
lint free cloth.
More stubborn marks can be
removed using a damp
(not wet) cloth. Wipe the
surface dry immediately
using a soft lint free cloth.
Do not use detergants, abrasive
cleaning products or cleaning
products that contain ammonia,
solvents or silicone as these
may damage the surface finish.
To protect the furniture,
position the furniture out of
direct sunlight and away from
direct heat sources such as
radiators and fires.
Do not place the furniture in
excessively dry and humid
conditions.
Do not place hot or cold
objects on the surface, always
use protective mats to avoid
marking the furnture.
Clean spills up immediately
Dispose of all packaging
carefully and responsibly
when assembly complete.
Do Not dispose of packaging
until assembly complete.

Please check you have all the panels listed below
Components -Panels
Left side (23.5x35.8cm)
Right side (23.5x35.8cm)
Code -
Code -
2
Important - Thick lines indicate finished edges
8302
8303
Bottom (134x34cm)
Backpanel (44.7x145cm)
Code - 8307
Top (141x38.8cm)
Drawer bottom (42.6x29.8cm)
Code -
4472
8300 8301
Code -
Code -
Right division (14.5x34cm)
Code - 9059
Left drawer side (30x10cm)
Code -
Drawer back (41.4x10cm)
Code -
Right drawer side (30x10cm)
Code -
622xx7002 624xx7005 623xx7002
Plinth (134x0.73cm)
Code - 8298
Front
Grooved
edge
Front
Grooved
edge
Drawer front (47.1x15.7cm)
Code - 8306
Trim x 2
(23.5cm long)
Code - 684006525
Left division (14.5x34cm)
Code - 9058

3
Components -Exploded View
Important - Thick lines indicate finished edges
8298
8306
4472
622xx7002
624xx7005
684006525
Trim
623xx7002
8300
8302
9058
8307
9059
8301
8303
684006525
Trim

70 80 90 100 110 120
0 10 20 30 40 50 60
mm
130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
Please check you have all the fittings listed below
Components-Fittings
Note: The quantities below are the correct amount to complete the assembly, In some case more fittings
may be supplied than are required.
Tools required
If you have damaged or missing components, call the
Customer Helpline: 0845 0613967 Please turn to back page
for important information when contacting Customer Helpline.
4
Cross headed screwdriver
(small & large )
Small Hammer
Tape Measure
Eye protection
(when using a
hammer)
Large cam x 16 - Code 760001103 Metal dowel x 18 - Code 760003004 Small cam x 2 - Code 760003005
Runner x 2 - Code 760001040
9mm bolt x 2 - Code 690001078
Handle x 1
Code 644003511
A B C
D H
I J L
45mm screw x 8 - Code 690001075
20mm bolt x 2 - Code 700002006
G
8mm screw x 4
Code 700003510

Step 1
Assembly Instructions
5
Fittings you will need for this step:
A
B
B
B
B
B
(x8)
Note: Insert metal
dowels as far as
shown by arrows.
Do not over tighten.
B
Fittings you will need for this step:
A
(x8)
Fitting dowels to top
panel
Fitting cams to plinth
and bottom panel
Step 2
Large
8300
B
8298
Note: Ensure cam
arrow points towards
the edge with hole.
A
B
B
A
A
A
A A
A
A
8301
B
B

6
Assembly Instructions
Step 3 Fittings you will need for this step:
A
(x4)
Large
B
(x8)
A
A
B
B
B B
Front grooved edge
Front grooved edge
8303
A
A
B
B
B B
8302
Step 4
Fitting cams and
dowels to left and
right hand end panels
Note: Ensure cam
arrow points towards
the edge with hole.
A
Note: Insert metal
dowels as far as
shown by arrows.
Do not over tighten.
B
B
Note: Ensure cam
arrow points towards
the edge with hole.
A
Fitting cams to left
and right hand
divider panels
Fittings you will need for this step:
A
(x4)
Large
A
A
A
A
9158 9159

9158
9158
7
Fittings you will need for this step:
(x1)
D
H
D
H
D
H
(x2)
Assembly Instructions
Step 5
9158
D
H
H
D
Step 6
a:Align the drawer
runner with the
edge of panel
, the 2nd hole from
the front will then line up
with a pre-drilled hole,
secure the runner to the
panel using screws .
Attaching runners
b:Slide the drawer
runner forward to
secure screw .
The hole in the runner will
line up with the pre-drilled
holes in the panel.
a:
b:
2ND
H
D
Note:
Please note
gap from the
front grooved edge.
Note:
Ensure these
holes are
positioned as shown.
D

9159
9159
8
Fittings you will need for this step:
(x1)
D
H
D
H
D
H
Assembly Instructions
Step 7
9159
D
H
H
D
Step 8
a:Align the drawer
runner with the
edge of panel
, the 2nd hole from
the front will then line up
with a pre-drilled hole,
secure the runner to the
panel using screws .
Attaching runners
b:Slide the drawer
runner forward to
secure 2 screws .
The hole in the
runner will line up with
the pre-drilled holes in
the panel.
(x2) a:
b:
2ND
H
D
Note:
Please note
gap from the
front grooved edge.
Note:
Ensure these
holes are
positioned as shown.
D

a: Insert dowels into
drawer front .
Note: Insert metal
dowels as far as
shown by arrows.
Do not over tighten.
9
Fittings you will need for this step:
(x2)
Drawer assembly
B
B
C
(x2)
Step 9
c: Insert wooden dowels
in drawer back
into holes in
left
right hand
drawer sides.
B
b: Insert small cams
into left
and right
drawer sides.
Note: Ensure cam arrow
points towards the edge
with hole.
C
C
B
B
Fittings you will need for this step:
Small
C
C
a:
b:
c:
Left hand side
Right hand side
Left hand side
Right hand side
Drawer Back
Continued on next page.
8306
8306
622xx7002
624xx7005
623xx7002
622xx7002
623xx7002
622xx7002
623xx7002
623xx7002
624xx7005
622xx7002
Assembly Instructions