Argos Malibu User manual

MADE IN
BRITAIN
Dimensions
Width - 74.5cm
Depth - 50cm
Height - 181cm
Malibu - 3 Drawer 2 Door Robe
Assembly Instructions - Please keep for future reference 630/2685
630/3158
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 3 - 11/10/13
Important - Please read these instructions fully before starting assembly
Ruler - Use this ruler to help correctly identify the screws
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
ALR2425
630/2427
630/2702
630/2661
Issue 2 - 17/09/12 - Added notes to drawer wrap preparation stages telling customer the cams can be either surface of the wrap
194/5999
189/7047
181/9551
192/6523
191/2180
147/2668
Issue 3 - 11/10/13 - 6 new codes added to front page.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 49kgs. Please lift
with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.
Glue Safety - Take care when using glue, please follow the advice below
Skin contact: Remove contami-
nation by washing with soap and
water. This procedure should be
followed prior to aeting and
drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
1
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• From time to time check that
there are no loose screws on
this unit.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Plinth - D0118A
714 x 92mm
x2
Rail - D0119A
714 x 66mm
Back Rail - D0120A
714 x 60mm
Components - Panels
Please check you have all the panels listed below
Glue Safety - Take care when using glue, please follow the advice below
Skin contact: Remove contami-
nation by washing with soap and
water. This procedure should be
followed prior to aeting and
drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
2
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• From time to time check that
there are no loose screws on
this unit.
Left Side (D0124A)
(1808 x 496mm)
Drawer Divider - D0034A
145 x 249mm
waterfall
1
Drawer Wrap (W162) x 3
(1308 x 95mm)
6
Plinth (D0128A) x 2
(714 x 92mm)
8
70%
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Right Side (D0125A)
(1808 x 496mm)
2
Drawer Front (D0131A) x 3
(710 x 157mm)
5
Base (D0126A)
(714 x 478mm)
4
Top (D0127A)
(714 x 494mm)
3
Drawer Base (T162) x 3
(299 x 695mm)
7
Hanging Rail (FHR704)
(704mm long)
10
Rail (D0129A)
(714 x 92mm)
9
Door (D0130A) x 2
(1199 x 353mm)
11 Foldy Back (XBO3379)
(1219 x 738mm)
12

Please check you have all the fittings listed below
Tools required
Glue Safety - Take care when using glue, please follow the advice below
Skin contact: Remove contami-
nation by washing with soap and
water. This procedure should be
followed prior to aeting and
drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
3
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• From time to time check that
there are no loose screws on
this unit.
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 12
B
Metal dowel (F901) x 6
C
Nail holder (F149) x 1
D F
G
40mm Screw (F910) x 12
J
13mm Screw (F79) x 1
H
25mm Screw (F50) x 8 Handle (F631) x 8
I
L
Rule
ScissorsSquare
Spirit
level
Hammer Bradawl
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Nail (F51) x 26
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
K
M ON
P Q
Bracket (F327) x 1
R (F601)
L (F600)
F599
F599
Drawer stops (F599) x 6
Runners (F600) x 3 and (F601) x 3
Electric drill
Step
ladder
Small locking
nut (F3) x 6
Rail holder
(F1014) x 2
E
13mm Screw (F63) x 10
19mm Connecting bolt
(F461) x 2
Hinge plate
(F523) x 4
Hinge (F522) x 4
25mm Connecting sleeve
(F432) x 2
Ruler - Use this ruler to help correctly identify the screws

Assembly Instructions
4
Prepare the 3 drawer
fronts and wraps
a: Screw 2 metal
dowels into the holes
on the back of the
drawer fronts .
Note: Tighten metal
dowels up fully against
the panels.
b: Insert 2 small locking
nuts into the holes
shown on the drawer
wrap .
Note: Arrow on locking
nut must point
towards hole in edge of
panel.
B
5
a:
b:
E
E
6
F
Assemble the drawers
a: Place the drawer
base into the narrow
slot on the drawer wrap
. . Fold wrap around
the base.
b: Turn drawer wrap
assembly over and push
onto the back of the
drawer front .
Turn locking nuts
clockwise to secure
panels - more than 1/2 a
turn.
7
6
5
E
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
80%
5
6
7
6
5
6
a:
b:
B
B
E
6
E
E
B
E
B
Step 1
Step 2
Note: Due to the manufacturing
process, the holes for the
locking nut can be on either
surface of the drawer sides.
Note: The locking nuts
can be on either surface
of the drawer sides.

Assembly Instructions
Use 2nd hole in from front of
Runner F1004 to fit 1st F73 then
fit other F73 to match other hole.
Rebated Edge
F73
COVERED EDGE
Use 2nd hole in from front of
Runner F1004 to fit 1st F73 then
fit other F73 to match other hole.
F1004
When you insert F900,
make sure the arrow is
pointing towards the hole
in the edge of the panel.
F900
F73
F1004
COVERED EDGE
5
Fit the drawer stops
Carefully break off the 2
drawer stops (F599) from
each pair of the drawer
runners .
Push the drawer stops
fully through the drawer
wraps from the
inside.
P
6
Attach the handles
Attach a handle to
each drawer front
using screw .
Note: Do not
overtighten the screw.
I
H
SNAP!
SNAP!
F599
P
P
F599
P
F599
P
F599
P
I
H
I
H
6
Step 4
Step 3
5
5

Assembly Instructions
Step 5
Use 2nd hole in from front of
Runner F1004 to fit 1st F73 then
fit other F73 to match other hole.
Rebated Edge
F73
COVERED EDGE
Use 2nd hole in from front of
Runner F1004 to fit 1st F73 then
fit other F73 to match other hole.
F1004
When you insert F900,
make sure the arrow is
pointing towards the hole
in the edge of the panel.
F900
F73
F1004
COVERED EDGE
6
Step 1
80% x 3
L
Prepare the left and
right side
Separate runners .
a: Push fit 3 left
runners marked ‘L’
into the holes shown on
left side .
Note: Runners must be
be fitted flat against the
panel. If necessary
gently tap into final
position.
Fit 2 hinge plates
making sure that the slot
is facing towards the
finished front edge.
Push rail holder into
the hole shown. Make
sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
b: Push fit 3 right
runners marked ‘R’
into the holes shown on
right side .
Fit 2 hinge plates
making sure that the slot
is facing towards the
finished front edge.
Push rail holder into
the hole shown. Make
sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
1
P
P
O
F
K
O
F
K
2
Finished
front edge
a:
b:
Finished
front edge
R
F601
F600
P
P
1
1
O
P
OF
K
P
P
O
P
2
2
O
P
P
P
O
O
F
K

Assembly Instructions
Step 6
Use 2nd hole in from front of
Runner F1004 to fit 1st F73 then
fit other F73 to match other hole.
Rebated Edge
F73
COVERED EDGE
Use 2nd hole in from front of
Runner F1004 to fit 1st F73 then
fit other F73 to match other hole.
F1004
When you insert F900,
make sure the arrow is
pointing towards the hole
in the edge of the panel.
F900
F73
F1004
COVERED EDGE
7
1
E
A
Prepare top and base
a: Tap 2 wooden
dowels into the ends
of the top .
b: Tap 2 wooden
dowels into the ends
of the base .
A
A
3
4
a:
b:
Fit the top and base
to the right side
Attach the top
to the right side
using the dowel
already fitted and
secure with 2
screws .
Attach the base
to the right side
using the dowel
already fitted and
secure with 2
screws .
3
4
2
2
G
G
Finished
front edge
Finished
front edge
Finished
front edge
plain chipboard surface
3
3
4
4
2
A
A
A
A
G
G
G
G
Step 7
plain chipboard surface

Finished
front edge
Assembly Instructions
Step 8
8
Prepare the 2 plinths
and the rail
a: Tap 2 wooden
dowels into the ends
of the 2 plinths .
b: Tap 4 wooden
dowels into the ends
of the rail .
Finished front edge
A
8
A
9
9
2
Fit the rail
Attach the rail to the
right side using the
dowels already fitted.
A
A
A
A
A
A
8
9
9
2
Step 9
Plain chipboard
surface
Plain chipboard
surface
Plain chipboard
surface

Assembly InstructionsAssembly Instructions
Use 2nd hole in from front of
Runner F1004 to fit 1st F73 then
fit other F73 to match other hole.
Rebated Edge
F73
COVERED EDGE
Use 2nd hole in from front of
Runner F1004 to fit 1st F73 then
fit other F73 to match other hole.
F1004
When you insert F900,
make sure the arrow is
pointing towards the hole
in the edge of the panel.
F900
F73
F1004
COVERED EDGE
9
This outer face should
be the same colour as
the main unit panels
Back
of unit
G
G
8
8
2
G
1
G
G
G
G
G
Fit the 2 plinths
2 people are needed
here
Attach the 2
plinths to
the right side
using the dowel
already fitted to
them and
secure with
screws .
Note: Support
the plinth at the back
of the unit until the left
side has been fitted in
the next stage.
8
2
G
Fit the left side
Push the left side
onto the unit and secure
with 6 screws .
G
1
Step 10
Step 11
Support
this plinth
8