Argos Adult Malibu 532/9717 User manual

MADE IN
BRITAIN
Dimensions
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Important - Please read these instructions fully before starting assembly
More help is available throughout this booklet by scanning
in the QR codes or typing in the links
Adult Malibu - Single Bedside
Assembly Instructions - Please keep for future reference 532/9717
565/5814
565/6291
553/2803
555/1231
Width - 38.3cm
Depth - 39.6cm
Height - 44.6cm
Issue 2 - 24/05/16
CR

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 10kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it must be
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Components - Panels
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Please check you have all the panels listed below When applicable, remove any
protective film before use
2
1 2 3
4
Left Side (DF7343)
(43.1 x 39.4cm)
Back (X375-350)
(37.5 x 35cm)
Right Side (DF7344)
(43.1 x 39.4cm)
Top (DF6020)
(38.3 x 39.6cm)
Shelf (DF7345)
(34.9 x 39.2cm)
Plinth (DF6021)
(34.9 x 9.2cm)
Drawer Front (DF6025)
(34.3 x 15.7cm)
Back Rail (DF6022)
(34.9 x 6cm)
Cross Rail (DF6023)
(34.9 x 6cm)
Left Drawer Side (W350-130LH)
(35 x 13cm)
Right Drawer Side (W350-130RH)
(35 x 13cm)
Drawer Back (W300-130)
(30 x 13cm)
Drawer Base (T311-347)
(31.1 x 34.7cm)
5 6 7
8 9 10
11
12 13

Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Components - Fittings
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
3
I
Plastic Nail (F91) x 4
H
9mm Screw (F73) x 6
A
Quickfit dowel (F545) x 14
C
Knock-in Peg (F171GY) x 4
D E
19mm Screw (F461) x 1
G
Wooden dowel (F22) x 16
J
Nail (F51) x 12
K
Handle (F418) x 1
Large locking cam nut (F607) x 14
B
Lb
La
350mm long
CL
CR
CR Runner (F424) x 1
CL Runner (F422) x 1
Lc
LdDR
DL
DL Runner (F425) x 1
DR Runner (F426) x 1
13mm Screw (F63) x 6
F
Tools required
Wedgefix (F639) x 2

Assembly Instructions
4
Step 1
Step 2
Fit the drawer sides
to the drawer front
Push the left drawer side
. and right drawer side
. down onto the back
of the drawer front .
Turn the large locking
cam nuts clockwise
as far as they will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
9
8
10
Prepare the drawer
sides
a: Insert a large locking
cam nut into the left
drawer side . and the
right drawer side .
Note: The arrow on the
locking cam nut must
point towards the
hole in the end of the
panel.
b: Push 1 of the quickfit
dowels as far as it will
go into the left drawer
side and the right
drawer side .
Note: Only the plastic
thread of the quickfit
dowel sticks out from the
panel.
A
9
10
B
A
a:
b:
B
9
10
A
B
910
AA
910
BB
8
10
9
B
B

C
C
9
Assembly Instructions
5
Step 3
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 4
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
12
109
8
11
9 10
12
11
11
C
9 10
9
8
10
12
910
9
C
C
11
12
D
K
Step 5
Fit the handle
Attach the handle to
the drawer front
using screw .
K
D
88

Fit runners to the
drawer
Fit the DL runner to
the bottom edge of the
left drawer side , as
shown, making sure that
it is pushed up against
the back of the drawer
front . Use a bradawl
to mark the fixing
positions, then secure
with 2 screws .
Fit the DR runner to
the bottom edge of the
right drawer side
using the same method.
Assembly Instructions
6
Step 6
10
L c
9
8
F
L d
Step 7
L d
F
F
L c
DL
F
F9
8
7
DR
DL
Runners must be
pushed up against
the drawer front
E
E
E
Fit the wedgefixes
Turn the drawer
assembly over and slide
2 wedgefixes into the
front and back grooves,
as shown, and tighten up
the screws.
E
Important: Make sure
that the drawer assembly
is square before fitting
the wedgefixes.
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
Fixing Bottom Mounter Runners

AG
G
A
10mm
G
A
B
Finished
front edge
1
Finished
front edge
1
Finished
front edge
Assembly Instructions
7
Step 8
Prepare the left side
a: Fit the CL runner
to the left side .
The 1st screw uses
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the hole at the top of the
runner .
c: Insert 2 large locking
cam nuts into the left
side .
Push 2 of the quickfit
dowels as far as they
will go into the left side
. .
Tap 2 wooden dowels
into the left side .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
L a
1
H
H
F
L a
L a
H
1st
screw
Finished
front edge
CL
Finished
front edge
F
CL
H
HH
L a
CL
F
CL
B
B
b:
c:
a:
A
1
B
1
G
1
1
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
Fixing Bottom Mounter Runners

AG
G
A
Assembly Instructions
8
Step 9
L b
H
1st
screw
Finished
front edge
CR
Finished
front edge
F
CR
H
H
H
L b
CR
F
CR
B
B
b:
c:
a:
Prepare the right side
a: Fit the CR runner
to the right side .
The 1st screw uses
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the hole at the top of the
runner .
c: Insert 2 large locking
cam nuts into the
right side .
Push 2 of the quickfit
dowels as far as they
will go into the right side
. .
Tap 2 wooden dowels
into the right side .
L b
2
H
H
F
L b
A
2
B
2
G
2
2
2
2
Finished
front edge
Finished
front edge
Finished
front edge
A
B

Finished
front edge
Finished
front edge
G
A
Assembly Instructions
9
Step 10
CL
A
G
Prepare the shelf
Insert 4 large locking
cam nuts into the
shelf .
Push 4 of the quickfit
dowels as far as they
will go into the shelf .
Tap 4 wooden dowels
into the shelf .
A
4
B
B
4
G
4
AB
B
B
A
G
G
A
B
B
4
Finished
front edge
Step 11
Fit the shelf onto the
left side
Push the shelf down
onto the left side .
Turn the 2 large locking
cam nuts clockwise
as far as they will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
Step 12
4
1
Step 13
G
G
Prepare the cross rail
Tap 4 wooden dowels
into the cross rail .
G
G
G
7Finished
front edge
4
1
Fit the cross rail onto
the left side
Push the cross rail
down onto the left side
. .
7
1
Note: The cross rail has no
holes drilled on either surface
7
Finished
front edge
CL
7
1
hps://www.youtube.com/watch?v=9C7tgv5xnbE
Carcase Assembly