Argos Montana 412/3653 User manual

MADE IN
BRITAIN
Dimensions
Width - 72cm
Depth - 33cm
Height - 186cm
Montana - Tall Display Unit
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 1 - 13/04/15
Important - Please read these instructions fully before starting assembly
ALR3146
412/3653
389/9201

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 35kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
overbalance protector kit
supplied or, an alternative fixing
method of your choice.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
1
80%
x 2
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Left End (DF3533)
(1803 x 309mm)
2
Top (DF3531)
(716 x 327mm)
Base (DF3532)
(716 x 327mm)
Left Door (DF3537)
(689 x 352.5mm)
Back (X1829-708)
(1829 x 708mm)
Right Door (DF3940)
(689 x 352.5mm)
Right End (DF3534)
(1803 x 309mm)
3
4
5
7 8
9
6
Fixed Shelf (DF3535)
(682 x 307mm)
Loose Shelf (DF3536)
(682 x 307mm) x 4

Rule
Tools required
Rule
ScissorsSquare
Spirit
level
Hammer Bradawl
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Step
ladder
Electric drill
(only use
when drilling
into walls)
Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
A B
D E F
G H I
L
N
C
M
J K
Large locking
nut (F900) x 8
Wooden dowel (F22) x 4 Metal dowel (F901) x 8
Shelf stud (F110) x 16
19mm Screw (F461) x 2
13mm Screw (F63) x 8
Handle (F341) x 2
Foot
(F233) x 4
Hinge (F518) x 4
Hinge plate
(F523) x 4
Nail (F51) x 34
40mm Screw (F910) x 4 38mm Screw (F81) x 8
Strap Screw Washer x 2
Overbalance protector kit (F269) x 1

Finished
front edge
Prepare the right end
Tap 2 wooden dowels
into the right side .
Screw 2 metal dowels
into the right end .
Insert 2 large locking
nuts into the right end
. .
Fit 2 hinge plates onto
the right end , making
sure that the slot is
facing towards the
finished front edge.
Prepare the left end
Tap 2 wooden dowels
into the left side .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Screw 2 metal dowels
into the left end .
Note: Tighten the metal
dowels up fully against
the panels.
Insert 2 large locking
nuts into the left end
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Fit 2 hinge plates onto
the left end , making
sure that the slot is
facing towards the
finished front edge.
A
A
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
C
B
Step 1
80% x 3
C
C
B
B
B
J
J
J
A
1
1
1
J
1
C
B
A
2
2
2
J
2
10mm
A
C
1
A
A
C
C
B
B
J
J
J
Step 2
2
Finished
front edge

Finished
front edge
Finished
front edge Finished
front edge
Assembly Instructions
5
Step 3
Step 4
Finished
front edge
Prepare the fixed shelf
Insert 4 large locking
nuts into the fixed
shelf .
C
5
C
C
C
C
B
C
Fit the fixed shelf to
the right end
Push the fixed shelf
onto the right end .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the fixed shelf .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
2
5
C
C
5
Step 5
Fit the left end
Push the left end
onto the fixed shelf .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the fixed shelf .
5
1
C
5
5
5
5
2
1

Finished
front
edge
Finished
front edge
Polystyrene
block
Assembly Instructions
6
Step 6B
B
B
B
Finished
front edge
Prepare the top
Screw 4 metal dowels
into the top .
B
3
3
Polystyrene
block
Polystyrene
block
Polystyrene
block
Step 7
Fit the top
Push the top onto
the left end and right
end .
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the left end and the
right end .
Note: To make it easier
to fit the top and base
panels, place
polystyrene blocks from
the packaging
underneath the end
panels to raise the
assembly.
1
2
3
C
1
21
2
3
Step 8
Fit the base
Fit the base onto the
left end and the right
end using 4 screws .
4
D
D
D
D
D
1
2
4
1
2

yy
Assembly Instructions
7
Step 9
Fit the feet
Fit the feet to the
base using screws .
N
4
EE
N
E
EE
NEE
N
EE
N
Warning: The
unit is heavy.
Lift with care.
b:
y
xx
xx
I
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back .
Note: Nails should be
spaced about 150mm
apart.
Carefully stand the
unit up for the next
step.
9
I
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
9
Step 10
9
4

Assembly Instructions
8
Step 11
Step 12
Hx 4
Hx 4
Hx 4
Hx 4
Fit the shelves
For each of the 4
shelves , insert 4 shelf
studs at the required
height.
Lower the 4 shelves
down onto the shelf
studs .
H
6
6
H
6
6
6
6
90
K
P
I
I
P
I
I
Prepare the 2 doors
Push fit 2 hinges into
the left door and the
right door .
Secure each hinge with
2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.
G
K
7
8
17
K
G
G
K
G
G
K
G
G
K
G
G
7
8

L
Assembly Instructions
9
Step 13
Fit doors and handles
Note: The easiest way to
attach each door and
. is to fit the top hinge
first, then align and fit the
other hinge.
a: Push the hinge
onto the front part of the
hinge plate .
The recess at the bottom
of screw B goes into the
slot in the hinge plate.
b: Keep the hinge
FLAT against the hinge
plate as you slide it
across as far as it will go.
Tighten screw A.
c: The hinge must be
flat against the hinge
plate prior to any
adjustment.
d: The hinge must
NOT be AT AN ANGLE
to the hinge plate
when assembled.
This would indicate that
the recess at the bottom
of screw B had not
located in the slot in the
hinge plate and the hinge
would not be secure.
Remove the hinge from
the hinge plate and then
re-assemble being
careful to follow
instructions a-c.
e: Attach a handle to
each door and
using screws .
K
K
K
J
J
J
K
J
L
F
7
8
7 8
a: b:
c: d:
J
K
J
J
B
J
F
K
K
K
A
K
J
B
e:
F
L
7
8
Note: The right door has
a small identification mark.