Argos Vancouver II 643/8133 User manual

Vancouver II -2 Door 3 Drawer Wardrobe
Dimensions
Width - 997cm
Depth - 603cm
Height -2057cm
Issue 1 - 20/10/09
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 0845 6400800
Assembly Instructions - Please keep for future reference
643/7842
643/7914
643/8229
643/8133
Tip : To prevent damage,
we recommend that you
build your unit on the
carton(s) it was packed in.

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Check you have all the
components and tools listed on
pages 2 and 3.
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Care and maintenance
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
Glue safety - Take care when using glue, please follow the advice below

Components - Panels
Please check you have all the panels listed below
2
Right side
(205.6 x 58cm)
2
P2349
Left side
(205.6 x 58cm)
1
P2349
Door x 1
(199.2 x 48.8cm)
4
P3304
Top/Bottom x 2
(96.7 x 57.7cm)
5
P1341
Upright small
(47.5 x 57.7cm)
6
P2348
Large horizontal
(96.7 x 57.6cm)
7
P1342
Small horizontal
(47.6 x 57.6cm)
8
P1343
Drawer base x 3
(45.4 x 34.9cm)
9
BO33955
Drawer wrap x 3
(35 x 46.7 x 9.5cm)
10
LA17955
Drawer front x 3
(48.8 x 15.7cm)
11
P4302
Plinth front
(145.7 x 14cm)
13
P7334C
Plinth back
(145.7 x 5.4cm)
14
P7335C
Pelmet
(99.9 x 4.5cm)
15
FA247
Foldy back
(199.3 x 98cm)
12
BO33933
Mirror door small
(151.2 x 48.8cm)
3
PS3305
xx

3
Please check you have all the ttings listed below
40mm Screw x 6
Ruler - Use this ruler to help correctly identify the screws
Tools required
A
10mm Fixing screw drawer x 12
E
30mm Screw x 10
B
26mm locking screw x 26
H
9mm Srew x 6
C
I
Door/Drawer handle x 5
Q
Note: The quantities below are the correct amount to complete the assembly. In some cases more
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
12.5 mm Screw x 2
F
L-Bracket x 1
15mm Screw x 13
D
Nail x 60
K
15mm Screw x 12
O
Large locking
nut x 20
M
P
Small locking
nut x 6
N
Nail holder x 1
L
G
J
Hinge door x 6
R
Runner x 6
ST
Components - Fittings If you have damaged or missing components,
call the Customer Helpline: 0845 6400800
Phillips screwdriver
(medium & large)
Flatblade screwdriver
Small
hammer
Ruler/tape
measure
Drill
Eye protection
(when using a
hammer or drill)
5mm Suitable drill bit
GR1988
Hanger rail large x 1
FK1268FK1269
Hinge back x 6
FK1324
FK1012
FK1010
FK1011
FK1301
FK1981
FK1322
FK1400
FK1311
FK1235
Hanger rail support x 2
FK1217
FK1309
Peg x 2
FK1234
FA1515 FK1419
PM1884
PM16951
5mm Suitable drill bit
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Stairs
Piercer Scissors
(medium)
(small)
Level ruler
Setsquare
U
Drawerbase support x 6
FK1250
V
Wall plug and parkerscrew x 1
ZF99936

4
Assembly Instructions
Step 1
Drawer assembly x 3
a: Insert two small locking
nuts into drawer wrap
.
Make sure the ‘arrow’ on
is pointing towards the
hole in the edge of .
J
10
b: Screw 24mm locking
screws into holes shown
on back of drawer front
.
Make sure 24mm locking
screws are tightened
right up against drawer
front .
J
10
10
J
J
11
H
H
H
11
H
11
11
H
a:
b:
c: Slide drawer base
into grooves shown on
drawer wrap .
9
10
9
10
c:

5
Assembly Instructions
Step 1 - continued
Attaching runners
d: Turn the drawer wrap
assembly over and push onto
the drawer front . Use a
phillips or atblade
screwdriver, that is a good t,
to turn 24mm locking srew
as far as it will go - more than
1/2 turn.
11
H
d:
I
e:
11
T
11
B
T
11
B
B
Step 2
a: Slide top of runners
foreward and x on right side
as shown using 10mm
xing screw drawer .
R
E
Finished
front edge
a:
R
R
R
R
E
E
E
E
2
2
2
I
e: Fix drawer handle
onto drawer front using
30mm screw .
Turn over drawer and
slide Drawerbase supports
in corner as shown and x
them, using the attached
screws .
N
U
U
U

b:
3
R
6
Assembly Instructions
a:
b:
a:
Step 2 - continuedStep 2 - continued
b: Slide top of runners
back.
Fix through 3rd hole of
runner and pre-drilled
holes of right side using
10mm xing screw drawer
.
Fix through 1st and 7th hole
of runners using 15mm
screw .
Note: there are no pre-
drilled holes for 15mm
screw .
Repeat a and b on upright
small .
E
O
R
R
2
R
O
Step 3
Insert ttings
a: Screw 24mm locking
screw into right side .
Note: Insert 24mm locking
screw as far as shown.
Do not over tighten.
Screw hinge back onto
right side .
6
H
2
2
H
H
b: Attach hanger rail
support using 12.5mm
screw onto right side .
M
F
P
2
2
P
2
P
P
P
H
H
H
H
H
H
HP
H
M
F
2
2
H
M
2F
Finished
front edge
E
R
R
R
E
E
E
3
O
O
O
O
O
O
OO

7
Assembly Instructions
Step 4
Attaching panels
Attaching plinths
a: Allign the sides of plinth
front with bottom as
shown and attach using
40mm screw .
Note: there are no
predrilled holes for 40mm
screw .
Note: top and bottom
panels are identical.
Only prepare one of the
panels at this satge. This
will be the bottom panel
Repeat with plinth back
.
A
Step 6
Position bottom , small
horizontal , large horizontal
and top onto right side
.
Insert large locking nuts
into bottom , small
horizontal , large horizontal
and top where shown.
Use a screwdriver to turn
locking nuts clockwise to
lock.
2
Top side
A
A
A
5
5
A
14
13
Step 5
Insert locking screws
a: Screw 24mm locking
screw into bottom .
H5
A
5
Top side
5
M
M
Unnished
back edge
H
H
I
I
5
I
I
5
I
I
I
I
I
I
I
I
I
2
5
7
5
5
8
7
5
8
7
14
13
Unnished
back edge
xx
8

H6
Step 8
Step 9
I
8
x
I
I
6
5
6
I
5
Attaching panels
Two people are needed here.
Position upright small onto
bottom and small
horizontal .
Insert two Large locking nuts
into upright small and
small horizontal where
shown.
Use a screwdriver to turn
locking nuts clockwise to
lock.
I
8
8
6
H
H
6
Unnished
back edge
8
Assembly Instructions
Step 7Step
Insert locking screws
Screw 24mm locking screw
into upright small .
M
MI
I
P
P
P
H
H
H
H
H
H
M
F
H
1
1
P
1
Insert ttings
Screw 24mm locking screw
into left side .
Note: Insert 24mm locking
screw as far as shown.
Do not over tighten.
Screw hinge back onto
upright .
1
H
H
Attach hanger rail
support using 12.5mm
screw onto left side .
M
F
P
1
2
H
M
1F
x
I

9
Assembly Instructions
I
Step 10
Step 11
I
I
I
I
I
I
I
M
MI
I
Attaching panel
Two people are needed here.
Position left side onto
bottom/top and large
horizontal .
Insert large locking nuts in
top/bottom and large
horiziontal .
Use a screwdriver to turn
locking nuts clockwise to
lock.
I
1
5
7
5
7
I
Fitting back panel
Attach foldy back to back
of wardrobe with the coloured
surface facing the inside of the
unit using nails and.
Use nail holder to hold the
nails vertical and at correct
distance as you secure the
foldy back .
Nails should be spaced
about 150mm apart.
K
12
12
K
K
L
Important:
Cabinet MUST
be ‘square’
when back is
attached. K
L
1
5
5
7
12
x