Argos Marlow 417/7654 User manual

MADE IN
BRITAIN
Dimensions
Width - 44.5cm
Depth - 39.5cm
Height - 50.5cm
Marlow - 2 Drawer Bedside
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 1 - 18/05/15
Important - Please read these instructions fully before starting assembly
ALR3186
417/7654
413/4219
404/2576

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 13kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Components - Panels
Please check you have all the panels listed below
2
12 3
80%
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
4
5
6
7 8 9
10 11
Left Side (DF3595)
(39 x 31.2cm)
Right Side (DF3596)
(39 x 31.2cm)
Top (DF3594)
(44.4 x 39.4cm)
Rail (DF3597)
(33.4 x 11.9cm) x 3 Drawer Front (DF3598)
(32.8 x 19.2cm) x 2
Leg (DF3599)
(49 x 5cm) x 4
Drawer Back (W301-124)
(30.1 x 12.4cm) x 2
Drawer Base (T312-347)
(31.2 x 34.7cm) x 2
Back (X385-260)
(38.5 x 36cm)
Left Drawer Side (W350-124LH)
(35 x 12.4cm) x 2
Right Drawer Side (W350-124RH)
(35 x 12.4cm) x 2

Please check you have all the fittings listed below
Tools required
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
A B
D E F
G H I
L
Small locking
nut (F3) x 4
C
Nail (F51) x 10
M
J
9mm Screw (F74) x 4
K
9mm Screw (F73) x 8
Drawer runner (F1004) x 4
38mm Screw (F81) x 12
Knock-in Peg (F171GY) x 8
Large locking
nut (F900) x 10
Metal dowel (F901) x 14
Wooden dowel (F22) x 10
Wedgefix (F639) x 4 Handle (F449) x 2
19mm Screw (F461) x 4
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver

6
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
x 2
x 2
x 2
x 2
A
B
A
C
C
CC
78
Step 2
Prepare the 2 drawer
fronts
Screw 2 metal dowels
into each of the drawer
fronts .
Note: Tighten the metal
dowels up fully against
the panels.
A
6
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
C
7
8
Attach the drawer
sides to the drawer
fronts
Push the left drawer sides
. and right drawer sides
. onto the back of the
drawer fronts .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
7
8
6
C
C
7
8
A
A
6
7
8
80%

F
6
Assembly Instructions
5
Step 4
F
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
10
7 8
6
9
7 8
10
9
9
F
7 8
x 2
x 2
x 2
F
F
Fit the wedgefixes
Turn the drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
K
x 2
K
K
K
10
7
8
7
8
10
9
H
H
L
Attach the handles
Attach a handle to
each of the drawer fronts
. using screws .
Step 7
H
6
L
6

5
5
Assembly Instructions
6
Step 8
Fit 2 legs to the left
side
Screw 2 legs to the
left side using 6
screws .
Note: The top of the
legs must be flush with
the top of the left side.
G
5
G
G
G
G
G
1
5
5
1
Step 9
G
G
G
G
G
2
Fit 2 legs to the right
side
Screw 2 legs to the
right side using
screws .
Note: The top of the
legs must be flush with
the top of the right side.
G
5
2
G
G
G
G
G
G
G
1
G
G
G
G
G
G
G
2
5
5
5
5

D
D
Assembly Instructions
7
Step 10
1
B
Prepare the left side
a: Place 2 runners on
the left side as
shown. Slide back the
top of runner and use the
2nd hole from the front
to fit the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the left side .
c: Screw 3 metal
dowels into the left
side .
Insert 2 large locking
nuts into the left side
. .
Note: The arrow on the
locking nuts must point
towards the hole in the
edge of the panel.
Tap 2 wooden dowels
into the left side .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
1
I
I
B
1
1
M
M
A
1
D
1
a:
b:
c:
I
M
I
M
1
I
I
1
B
A
B
A
A
10mm
D
I
M

D
D
Assembly Instructions
8
Step 11
Prepare the right side
a: Place 2 runners on
the right side as
shown. Slide back the
top of runner and use the
2nd hole from the front
to fit the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the right side .
c: Screw 3 metal
dowels into the right
side .
Insert 2 large locking
nuts into the right
side .
Tap 2 wooden dowels
into the right side .
2
I
I
B
2
2
M
M
A
2
a:
b:
c:
2
I
M
I
M
2
I
I
2
A
A
A
B
B
D
2
I
M

D
Assembly Instructions
9
Step 12 B
B
D
Prepare the 3 rails
Insert 2 large locking
nuts into each of the
rails .
Tap 2 wooden dowels
into each of the rails .
B
4
D
4
x 3
B
A
Fit the rails
Push the 3 rails onto
the left side .
Use a screwdriver to
tighten the large locking
nut fitted to each of
the 3 rails .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
1
4
B
B
4
Step 13
Fit the right side
Push the right side
onto the 3 rails .
Use a screwdriver to
tighten the large locking
nut fitted to each of
the 3 rails .
Stand the unit up for
the next step.
4
2
B
4
Step 14
4
4
4
4
1
4
4
4
2