Argos 1589317 User manual

Shelf unit + Desk
Dimensions
Length - 83/95cm
Depth - 37/49cm
Height - 73/13cm
Weight - 20kg
Issue 1 - 15/05/14
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
0045 7668 8055 or e-mail: order@flexa.dk
Assembly Instructions - Please keep for future reference 1589317

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could
damage the unit. Only use hand
screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Shelf x1
(76.5x33.1x1.5cm)
3
Components - Parts
Please check you have all the parts listed below
Top x1 (82.5x37x1.5cm)
4
No. 15-01507651-20
2
Side panel Right x1
(70.6x35x1.5cm)
2
No. 15-01507061-20
Back panel x1
(78.2x64.8/32.4x0.3cm)
5
No. 4309-0307821
Side panel Left x1
(70.6x35x1.5cm)
1
No. 15-01507062-20
Plinth x1 (76.5x6.5x1.5cm)
7No. 12-01507651-20
Base x1 (76.5x33.1x1.5cm)
6No. 15-01507652-20
If you have damaged or missing components,
call the Customer Helpline: 0045 7668 8055
No. 15-01508252-20

1.2x20mm Nail square x25
Please check you have all the fittings listed below
7x34mm for ø5 Minifix bolt x14
A
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
ø15x9.5mm Minifix cam x14
B
5x30 mm Dowel x14
C
ø5x16mm Shelf support x4
D
Components - Fittings
3
ENo. 4022-006
Tools required
Phillips
screwdriver
(medium)
Small
hammer
Flatblade
screwdriver
(medium)
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
No. 3930-05030
No. 4013-003
No. 3933-15010
No. 4020-005

4
Assembly Instructions
Step 1
Step 2
Attach the dowels Cto
plinth 7, base 6, side
panels 1and 2.
It may be necessary
to tap the dowels in
very gently with a small
hammer.
Attach minifix bolts Ato
side panels 1and 2.
Attach side panels 1
and 2to the base 6
and plinth 7with the
minifix cams B.
1
7
2
1
2
6
7
6
C
C
C
C
C
A
AA
B
B
B
B
B

Assembly Instructions
Step 3
Attach minifix bolts Ato
top 4.
Attach top 4to side
panels 1and 2with
the minifix cams B.
5
4
Step 4
4
6
1
2
AA
A
B
B
B

Assembly Instructions
Attach the back panel
5with nails Eto the
back side of the shelf and
carefully tap the nails E
in the circumferance.
Position the shelf
supports Dinto the
holes in the side panels
1and 2. Shelf
supports should be at the
same level.
Place shelf 3onto the
shelf supports D.
Assembly of this
furniture is finished.
Step 5
3
Step 6
6
5
1
2
E
E
D
D

Components - Parts
Please check you have all the parts listed below
Support arm x1
(45.0x11.5x1.8cm)
9
No. 12-01804501-20
Table top x1
(95.0x48.5x1.5cm)
8
No. 15-01509501-20
If you have damaged or missing components,
call the Customer Helpline: 0045 7668 8055
7

8
Please check you have all the fittings listed below
i
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
3.5x16mm Chipboard screw x24
J
G
ø10x18mm Barrel nut x1
H
50x50x15x2mm Angle x6
F
Components - Fittings
M6x100mm Connecting bolt x1
No. 3922-06018 No. 4008-019
No. 3901-35016
No. 3930-10045
No. 3913-061001
Tools required
Phillips
screwdriver
(medium)
Small
hammer
Allen key
4mm incl.
Flatblade
screwdriver
(medium)
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
No. 4033-004
10x45 mm Dowel x2

Assembly Instructions
Step 7
Attach the dowels ito
the support arm 9.
It may be necessary
to tap the dowels in
very gently with a small
hammer.
Put the barrel nut Hto
the support arm 9.
Attach the support arm
9to the bed leg with the
connecting bolt G.
9
Step 8
9
9
9
i
H
G
G
H
G
H