Argos Kensington 424/7429 User manual

MADE IN
BRITAIN
Dimensions
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Important - Please read these instructions fully before starting assembly
Kensington - 3 Drawer 3 Door Robe
Assembly Instructions - Please keep for future reference
ALR3178
424/7429
402/7216
Width - 127.4cm
Depth - 49.5cm
Issue 1 - 19/06/15
Height - 198.8cm

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 85kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
overbalance protector kit
supplied or, an alternative fixing
method of your choice.
• Dispose of all packaging
carefully and responsibly.
Rule
Tools required
Rule
ScissorsSquare
Spirit
level
Hammer Bradawl
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Step
ladder
Electric drill
(only use
when drilling
into walls)
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Components - Panels
Please check you have all the panels listed below
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
2
78 9
80% x 3
90% x 1
14
Left Side (DF3773)
(197.3 x 47.5cm)
Divider (DF3776)
(197.3 x 47.5cm)
Right Side (DF3774)
(197.3 x 47.5cm)
Top (DF3772)
(127.4 x 49.5cm)
Narrow Rail (DF3777)
(40 x 8.9cm) x 2
Front Plinth (DF3775)
(127.4 x 9.2cm)
Side Plinth (DF2431)
(47.5 x 9.1cm) x 2
Rail (DF2412)
(79.7 x 8.9cm) x 5
10
Large Shelf (DF2413)
(79.7 x 47.4cm)
6
11
Large Hanging Rail (FHR791)
(79.1cm long)
12
Small Hanging Rail (FHR394)
(39.4cm long)
13
15 17
1816
Drawer Front (DF2414)
(79.1 x 19.2cm) x 3
Drawer Back (W765-124)
(76.5 x 12.4cm) x 3
Left Drawer Side (W370-124LH)
(37 x 12.4cm) x 3
Drawer Base (T776-367)
(77.6 x 36.7cm) x 3
Right Drawer Side (W370-124RH)
(37 x 12.4cm) x 3
1 2 3
4 5
Narrow Shelf (DF3778)
(40 x 45cm)
Narrow Base (DF3779)
(40 x 47.4cm)

Components - Panels
Please check you have all the panels listed below
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
3
19 Large Door (DF3767)
(184.5 x 39.4cm)
20 21
Small Left Door (DF3874)
(120.6 x 39.4cm)
Small Right Door (DF3780)
(120.6 x 39.4cm)
Small Back (X1892-419)
(189.2 x 41.9cm)
Large Back (X1914-816)
(191.4 x 81.6cm)
22 23

Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Components - Fittings
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
4
A B
D E F
G H I
L
N
Small locking
nut (F3) x 6
C
Nail (F51) x 42
M
J K
O
Drawer runner (F1004) x 6
Knock-in Peg (F171GY) x 12
Large locking
nut (F900) x 34
Metal dowel (F901) x 38
Wooden dowel (F22) x 30
25mm Screw (F50) x 6 19mm Screw (F461) x 9 9mm Screw (F74) x 6
9mm Screw (F73) x 12 Plastic Nail (F91) x 6
Handle (F220) x 9
P Q
Hinge plate
(F523) x 10 Hinge (F522) x 10
S
Shelf stud (F110) x 2
Rail Holder
(F891) x 4
13mm Screw (F63) x 28
Wedgefix (F639) x 12
R
U
W X
Back holder (F276) x 6
*These can
also be round
Nail screw (F277) x 6
Large wooden dowel (F40) x 1
V
Double metal dowel (F566) x 1
TStrap
Screw Washer x 2
Overbalance protector kit (F269) x 1

Assembly Instructions
5
Step 1
1
A
A
C
C
C
C
23
Step 2
Prepare the 3 drawer
fronts
Screw 2 metal dowels
into each of the 3 drawer
fronts .
Note: Tighten the metal
dowels up fully against
the panels.
A
1
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
C
2
3
Attach the drawer
sides to the drawer
fronts
Push the left drawer sides
. and right drawer sides
. onto the back of the
drawer fronts .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
2
3
1
C
C
2
3
A
A
1
2
3
x 3
x 3
x 3
x 3

Assembly Instructions
6
Step 4
1
F
F
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
5
2 3
1
4
2 3
5
4
4
F
2 3
Step 7
Fit the wedgefixes
Turn the drawer
assemblies over and
slide 4 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
N
F
F
N
N
N
N
N
5
2
3
4
2
3
5
Attach the handles
Attach 2 handles to
each drawer front
using screws .
H
1
R
H
H
R
R
1
x 3
x 3
x 3
x 3

D
D
Assembly Instructions
7
Step 8
K
O
K
O
Prepare the divider
a: Place 3 runners on
the divider as shown.
Slide back the top of
runner and use the 2nd
hole from the front to fit
the 1st screw .
Fit 3 hinge plates onto
the divider , making
sure that the slot is
facing towards the
finished front edge.
b: Slide the runners
back the other way and
fit the 2nd screw into
the corresponding holes
in the divider .
Insert 2 large locking
nuts into the divider
. .
Note: The arrow on the
locking nuts must point
towards the hole in the
edge of the panel.
Tap 2 wooden dowels
into the divider .
c: Screw 6 metal
dowels into the
divider .
To fit the rail holder
screw through the top
hole with screw and
into the mark hole drilled
in the divider . Make
sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.
9
J
J
B
9
9
M
M
A
9
D
9
P
9
O
K
9
K
P
J
M
a:
b:
c:
Finished
front edge
J
M
J
M
J
M
P
P
P
J
J
J
B
B
Finished
front edge
Finished
front edge
A
A
A
A
A
A
K
K
O
B
10mm
D
9
9
9

Finished
front edge
Finished
front edge
Assembly Instructions
8
Step 9
Turn the divider over
and prepare its other
surface
Screw 5 metal dowels
into the divider .
To fit the rail holder
screw through the top
hole with screw and
into the mark hole drilled
in the divider . Make
sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.
A
A
A
A
A
K
K
O
A
9
O
K
K
99
D
D
Prepare the large shelf
Insert 4 large locking
nuts into the large
shelf .
Tap 4 wooden dowels
into the large shelf .
6
D
6
B
B
B
D
D
B
B
Finished
front edge
6
Step 11
Fit the large shelf to
the divider
Push the large shelf
onto the divider .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the large shelf .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
6
9
B
B
6
A
B
Step 10
Finished
front edge
6
9

Finished
front edge
D
D
Assembly Instructions
9
Step 12
Prepare the narrow
base
Insert 4 large locking
nuts into the narrow
base .
Tap 4 wooden dowels
into the narrow base .
11
D
11
B
B
B
B
B
D
D
Finished
front edge
9
Step 13
Fit the narrow base to
the divider
Push the narrow base
onto the divider .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the narrow base .
11
9
B
11
11
11
D
Step 14
B
B
Prepare 1 of the
narrow rails
Insert 2 large locking
nuts into the narrow
rail .
Tap 1 wooden dowel
into the narrow rail .
15
D
15
B15
10
11
Narrow Shelf (DF3778)
(40 x 45cm)
Narrow Base (DF3779)
(40 x 47.4cm)