Argos Marlow 424/2929 User manual

MADE IN
BRITAIN
Dimensions
Width - 91.1cm
Depth - 49.5cm
Height - 191.8cm
Marlow - 2 Door Robe
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 1 - 22/05/15
Important - Please read these instructions fully before starting assembly
ALR3182
424/2929
395/5530
404/2260

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 58kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
overbalance protector kit
supplied or, an alternative fixing
method of your choice.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
12 5
80%
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
6
Left Side (DF3918)
(180.3 x 41.3cm)
Right Side (DF3919)
(180.3 x 41.3cm)
Top (DF3625)
(91.1 x 49.5cm)
Horizontal (DF3930)
(79.7 x 45.9cm) x 2
Leg (DF3631)
(190.3 x 5cm) x 4
Door (DF3920)
(180 x 39.4cm) x 2
Back (X1798-823)
(179.8 x 82.3cm)
Hanging Rail (FHR791)
(79.1cm long)
7
3
8 9
Rail (DF3742)
(79.7 x 11.9cm)
4

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Rule
Tools required
Rule
ScissorsSquare
Spirit
level
Hammer Bradawl
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Step
ladder
Electric drill
(only use
when drilling
into walls)
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A B
D E F
G H I
L
C
Nail (F51) x 36
J K
38mm Screw (F81) x 36
Large locking
nut (F900) x 10
Metal dowel (F901) x 10 Wooden dowel (F22) x 14
19mm Screw (F461) x 4
M
40mm Screw (F910) x 4
Rail Holder
(F891) x 2
13mm Screw (F63) x 16
Handle (F449) x 2
Hinge plate
(F523) x 6 Hinge (F522) x 6
Strap Screw Washer x 2
Overbalance protector kit (F269) x 1

Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
80% x 3
90% x 1
Fit 2 legs to the left
side
Screw 2 legs to the
left side using 18
screws .
Note: The top of the
legs must be flush with
the top of the left side.
G
6
1
Step 2
Fit 2 legs to the right
side
Screw 2 legs to the
right side using 18
screws .
Note: The top of the
legs must be flush with
the top of the right side.
G
6
2
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
1
6
6
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
2
6
6

C
C
C
C
Assembly Instructions
5
Step 3
1
2
A
10mm
C
A
A
A
A
A
A
A
A
I
D
I
D
K
K
A
K
K
I
I
D
Prepare the left side
Screw 5 metal dowels
into the left side .
Note: Tighten the metal
dowels up fully against
the panels.
Tap 2 wooden dowels
into the left side .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
To fit the rail holder ,
screw through the top
hole with screw and
into the mark hole drilled
in the left side . Make
sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.
Fit 3 hinge plates onto
the left side , making
sure that the slot is
facing towards the
finished front edge.
A
1
C
1
A
D
I
I
1
K
1
II
D
K
K
K
K
Step 4
Prepare the right side
Use the same fittings you
used for the left side to
prepare the right side .
2

Finished
front edge
Finished
front edge
C
Assembly Instructions
6
Step 5
Prepare the 2
horizontals
Insert 4 large locking
nuts into each of the
horizontals .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Tap 2 wooden dowels
into each of the
horizontals .
B
B
B
B
B
C
C
C
B
3
C
3
3
Finished
front edge
x 2
A
B
Fit the 2 horizontals
to the right side
Push the 2 horizontals
onto the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
each horizontal .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
2
3
B
B
3
3
3
Step 6
Step 7B
B
C
C
Finished
front edge
Prepare the rail
Insert 2 large locking
nuts into the rail .
Tap 2 wooden dowels
into the rail .
B4
4
C
4
2

Assembly Instructions
7
Step 8
Step 9
Fit the left side
Push the left side onto
the assembly.
Use a screwdriver to
tighten the 5 large
locking nuts fitted to
the 2 horizontals and
the rail .
Finished
front edge
Fit the rail
Push the rail onto the
right side .
Use a screwdriver to
tighten the large locking
nut fitted to the rail .
Note: Support the rail
until the left side has
been fitted in the next
step.
2
4
B4
3
3
2
4
3
3
4
1
B
3
4

y
y
yy
xx
Finished
front edge
F
F
F
F
Assembly Instructions
8
Step 10
Fit the top
Attach the top to the
sides and using
the 4 screws .
Step 11
1
2
F
5
1 2 5
b:
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back .
Note: Nails should be
spaced about 150mm
apart.
Carefully stand the
unit up for the next
step.
9
E
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
9
xx
E
Warning: The
unit is heavy.
Lift with care.
9

Assembly Instructions
9
Step 12
7
D
Fit the hanging rail
Push the hanging rail
into the rail holders
fitted to the side panels.
7
D
7
Step 13
Prepare the 2 doors
Push fit 3 hinges into
each of the 2 doors .
Secure each hinge with
2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.
I
L
8
L
I
I
90
L
x 2
L
I
I
L
I
I
8