Argos Matrix 609/0739 User manual

Matrix Console Table -Metal / Glass
Assembly Instructions - Please keep for future reference 609/0739
609/0454
Dimensions
Width - 90cm
Depth - 30cm
Height - 76cm
Important - Please read these instruction fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 12/01/09

1
Safety and Care Advice
Important - Please read these instru ctions fully before starting assembly
components and tools listed on
pages 2 and 3.
plastic bags and separate them
into their groups.
away from the work area, small
parts could choke if swallowed.
space to layout the parts before
starting.
room) as possible.
surface to avoid damaging the
easier with 2 people.
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
carefully and responsibly.
and mild detergent, do not use
bleach or abrasive cleaners.
there are no loose screws on
this unit.
discarded with household
waste. Take to your local
authority waste disposal centre.
Care and maintenance
if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Note:
Warning
Do not place very hot or very
cold items against or in close
proximity to glass surfaces
unless an adequately thick
insulating material is used to
prevent such items from coming
into contact with the glass.
Do not sit or stand upon the
glass surface(s).
Do not use the glass as a
chopping surface. Do not strike
the glass with hard or pointed
items.
Keep These Instructions For Future Reference
This product complies with
BS EN 14749:2005
Argos plc
489-499 Avebury Boulevard
Central Milton Keynes
MK9 2NW
Batch No./Date of manufacture:
this could cause damage.
Do not stand on the product,
If a glass component is chipped
or broken, stop using the product
and consult the manufacturer or
supplier.

Components - Panels
Please check you have all the pan els listed below
2
2
Metal tube x 4
(5.08 x 53cm)
5
1
Metal tube x 4
(5.08 x 5.5cm)
6
Feet x 4
(5.2 x 1.3cm)
7
Metal rod x 4
(74.5 x 0.7cm)
Glass top x 1
(90 x 30cm)
4Glass shelf x 2
(90 x 30cm)
Metal tube x 4
(5.08 x 13.5cm)
3

Tools required
If you have damaged or missing components,
call the Customer Helpline: 08456 400800
Components - Fittings
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 120105 115 125 130 135 140 145 150 155 160 165 170
3
Screw driver
(not included)
Drill
(not included)
Hammer
(not included)
Wall mounting strap x 2
A

top
1 1 1 1 1
as shown.
1 1 1 1 1
as shown.
1
as shown.
1
top
1 1 1 1
top
1
11111111111
Assembly Instructions
Step 1
Finger tighten 4 pcs of
metal rods onto glass
top as shown.
Step 2
Put 2 pcs of wall straps
through metal rods .
4
A
22
2
2
Fitting Metal Rod
Fitting Wall Straps A
A
1
2
2
2
2
.
2
2
1
1

rods as
2
rods
2
rods
2
Assembly Instructions
Step 3
Attach 4 pcs of metal
tubes through 4 pcs
of metal rods as
shown.
Step 4
Please be careful to
place glass shelf
through 4 pcs of metal
rods as shown.
5
4
3
2
2
2
1
3
3
3
3
2
2
2
3
2
2
Matt surface
3
3
Fitting Metal Tube
Attaching Glass Shelf
2
3
2
4

tubes
5
tubes
5
tubes
5
tubes
5
tubes
5
tubes
5
tubes
5
2
Assembly Instructions
Step 5
Attach 4 pcs of metal
tubes through 4 pcs
of metal rods as
shown.
Step 6
6
Please be careful to
place glass shelf
through 4 pcs of metal
rods as shown.
5
5
5
5
2
2
2
2
3
5
5
5
5
4
4
4
2
Matt surface
2
2
A
A
Fitting Metal Tube
Attaching Glass Shelf
5 5
2
2
4

4
6
down.4
Assembly Instructions
Step 7
Attach 4 pcs of metal
tubes through 4 pcs
of metal rods
as shown.
Step 8
a: Push two sides of
glass down.
7
4
4
1
A
A
6
6
6
6
4
4
5
5
5
5
a:
2
2
2
2
Fitting Cap
Fitting glass shelf
in position
2
6
4 4

Assembly Instructions
b: Finger tighten 4 pcs
of feet onto metal
rods as shown.
Step 9
8
2
7
4
7
7
7
7
2
2
2
2
4
4
A
1
3
b:
1
Straighten up the wall
straps as shown .
Step 8-continued
A
A
Adjust Wall strap
A

Assembly Instructions
Step 10
9
3
4
2m
3.m
5
2m
2.5m
Ø6 mm
BRICK
MIN
Fixing to wall
It is recommended that
the unit is fixed to a wall.
Fix wall strap to top of
the unit by using screw.
With help, move the unit
into position.
Mark fixing hole on wall
and remove the unit.
Drill 6mm hole and insert
wall plug.
Reposition the unit and
fix wall strap by using
screw.
Warning:
The unit is
heavy.
Lift with care.
Warning:
Before drilling,
check wall for
hidden pipes
and cables.
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
3