Argos Linear 247/8173 User manual

MADE IN
BRITAIN
Dimensions
Linear - 3 Drawer Chest
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 10/06/14
Important - Please read these instructions fully before starting assembly
ALR3057
247/8173
247/5633
259/7470
Width - 79.5cm
Depth - 39cm
Height - 65.5cm

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 22.5kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
80%
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
12 3
4 5
6 7 8
9
10
Left Side (DF141)
(579 x 366mm)
Base (DF147)
(791 x 368mm)
Right Side (DF142)
(579 x 366mm)
Top (DF143)
(795 x 390mm)
Drawer Back (W708-124)
(708 x 124mm) x 3
Drawer Base (T719-347)
(719 x 347mm) x 3
Left Drawer
Side (W350-124LH)
(350 x 124mm) x 3
Right Drawer
Side (W350-124RH)
(350 x 124mm) x 3
Back (X785-600)
(785 x 600mm)
Drawer Front (DF145)
(783 x 186mm) x 3

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
B C
D E F
G H
Small locking
nut (F3) x 6
Nail (F51) x 19
I
A
Wooden dowel (F22) x 8 Metal dowel (F901) x 10
Large locking
nut (F900) x 4 Knock-in Peg (F171GY) x 12
MR Runner (F160) x 3
b
L Runner (F161) x 3
Mc
L Runner (F159) x 3
Ma
R Runner (F162) x 3
Md
350mm long
40mm Screw (F910) x 4
N
13mm Screw (F52) x 18
J
13mm Screw (F79) x 16 13mm Screw (F63) x 18
KL
Wedgefix (F639) x 12
N
Foot
(F233) x 4
O
38mm Screw (F81) x 8
N
P
N
P
Bracket (F327) x 1
P
Handle (F283) x 3
780mm long

5
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
B
B
B
C
C
CC
78
Step 2
Prepare the 3 drawer
fronts
Screw 2 metal dowels
into each of the drawer
fronts .
Note: Tighten the metal
dowels up fully against
the panels.
B
5
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
C
7
8
Attach the drawer
sides to the drawer
fronts
Push the left drawer sides
. and right drawer sides
. onto the back of the
drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
7
8
5
C
C
7
8
B
B
5
8
7
8
x 3
x 3
x 3
x 3
80%

5
E
E
Assembly Instructions
5
Step 4
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
9
7 8
5
6
7 8
9
6
6
E
7 8
E
E
9
7
8
9
6
7
8
Fit the handle
Position a handle
onto the top edge of the
drawer front .
Fix the handle to the
back surface of the
drawer front using 5
screws .
P
5
P
J
5
J
J
J
J
J
P
5
x 3
x 3
x 3

Assembly Instructions
6
Step 7
Fit the wedgefixes
Turn the drawer
assemblies over and
slide 4 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
L
L
LL
L
L
Fit runners to the
drawers
Fit the runner to the
bottom edge of the left
drawer side , as
shown, making sure that
it is pushed up against
the back of the drawer
front . Use a bradawl
to mark the fixing
positions, then secure
with 2 screws .
Fit the runner to the
bottom edge of the right
drawer side using the
same method.
8
M c
7
5
K
M d
K
K
M d
Runners must be
pushed up against
the drawer front
7
5
Step 8
M c
8
K
K
x 3
x 3

A
A
Finished
front edge
Finished
front edge
Assembly Instructions
7
Step 9
a:
M a
I
Finished front edge
I
1st
screw
2nd
screw
I
3rd
screw
b:
c:
M a
Finished front edge
K
Prepare the left side
a: Fit 3 runners to
the left side .
The 1st screw uses
the 2nd hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the 2nd hole in at the top
of the runners .
c: Tap 4 wooden
dowels into the left
side .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 2 large locking
nuts into the left side
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
A
D
1
1
M a
1
I
I
K
M a
1
Finished
front edge
1
1
I
M a
I
I
I
M a
I
I
I
M a
I
I
K
K
K
A
A
10mm
A
D
D
D

A
A
Assembly Instructions
8
Step 10
Prepare the right side
a: Fit 3 runners to
the right side .
The 1st screw uses
the 2nd hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the 2nd hole in at the top
of the runners .
c: Tap 4 wooden
dowels into the right
side .
Insert 2 large locking
nuts into the right
side . .
M b
2
I
I
K
M b
M b
I
Finished front edge
I1st
screw
2nd
screw
I3rd
screw
a:
b:
c:
A
D
2
2
M b
Finished front edge
K
Finished
front edge
2
Finished
front edge
2
Finished
front edge
2
I
I
M b
I
I
I
M b
I
I
I
M b
I
K
K
K
D
D
A
A

Finished
front edge
Finished
front edge Finished
front edge
Assembly Instructions
9
Step 11
Prepare the top
Screw 4 metal dowels
into the top .
Fix the bracket in the
middle of the top ,
flush to the rebated back
edge using screw .
B
3
Fit the right side to
the top
Push the right side
onto the top .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the right side .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
3
2
D
D
2
Step 12
Fit the left side
Push the left side
onto the top .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the left side .
3
1
D
1
Step 13
B
D
B
B
B
B
Finished
front edge
3
3
2
O
O
J
J
O
3
3
1