Argos Caspian 365/6499 User manual

MADE IN
BRITAIN
Dimensions
Width - 73.5cm
Depth - 44.5cm
Height - 72cm
Caspian - 2 Door Cupboard
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 4 - 27/10/14
Important - Please read these instructions fully before starting assembly
365/6499
339/9426
ALR3100
Issue 2 - 13/11/12 - Cat code added - 631/3619
Issue 3 - 15/11/12 - Cat code 631/3619 should have been 621/3619
Issue 4 - 27/10/14 - New MK BQSP version.
Added Plastinails to kit.
New Argos codes.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 21kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Components - Panels
Please check you have all the panels listed below
2
12
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
4
Left Side (D1193A)
(706 x 394mm)
Top (D1195A)
(733 x 444mm)
Shelf (D1197A)
(698 x 373mm)
Plinth (D0879A)
(698 x 80mm)
Back (X848)
(718 x 622mm)
Right Side (D1194A)
(706 x 394mm)
Door (D1172A)
(623 x 345mm) x 2
Base (D1196A)
(698 x 378mm)
3
6
5
7
8

Please check you have all the fittings listed below
Tools required
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
A
Wooden dowel (F22) x 2
B
Metal dowel (F901) x 4
C
D
G
E
Large locking
nut (F900) x 4
F
40mm Screw (F910) x 6
H I
L
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Nail (F51) x 16
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J K
Electric drill
(only use when
drilling into walls)
Handle (F923) x 2
13mm Screw (F63) x 8 Shelf support (F121) x 4
19mm Screw (F461) x 4
Hinge plate
(F523) x 4 Hinge (F522) x 4 Plastic Nail (F91) x 5
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.

Prepare left side
Fit 2 hinge plates onto
the left side , making
sure that the slot is
facing towards the
finished front edge.
Insert 2 large locking
nuts into the left side
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
Step 2
Finished
front edge
1
J
J
J
J
1
80%
Insert 4 large locking
nuts into the
horizontal as shown.
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
C
C
C
1
C
C
2J
J
2
J
Finished
front edge
C
1
Prepare right side
Fit 2 hinge plates onto
the right side , making
sure that the slot is
facing towards the
finished front edge.
Insert 2 large locking
nuts into the right
side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
J
2
C
2

E
Finished
front edge
E
E
A
Finished
front edge
Assembly Instructions
5
Step 3
Step 4
Join the right side and
base
Attach the base to
the right side using 2
screws .
plain chipboard surface
5
2
5
2
E
A
plain chipboard surface
10mm
A
Prepare the plinth
Tap 2 wooden dowels
into the plinth .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Step 5
Fit the plinth
Attach the plinth to
the right side using
screw .
A
7
7
7
E
2
plain chipboard surface
7
2

Finished
front edge
Assembly Instructions
6
Step 6
E
E
E
Join the left side and
base
Attach the left side to
the base and plinth
. using 3 screws .
1
5
7E
1
7
5
Step 7
Prepare the top
Screw 4 metal dowels
into the top .
Note: Tighten the metal
dowels up fully against
the panels.
B
B
B
B
B
B
4
plain chipboard surface
4
Finished
front edge

Assembly Instructions
7
Step 8
Step 9
C
B
Fit top
Push the top onto
the side panels and
. .
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the inside of the side
panels and .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
4
1
2
C
1 2
C
yy
x
x
b:
E
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail along the sides
and bottom edge of the
back .
Note: Nails should
be spaced about 150mm
apart.
Tap 2 plastic nails
into the bottom edge of
each of the sides and
. and 1 into the
middle of the plinth .
Stand the unit up.
8
D
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
9
88
x
y
y
x
D
4
1
2
L
1
7
2
L
LL
L
L
1
7
2
Warning: The
unit is heavy.
Lift with care.

Assembly Instructions
8
Step 10
Step 11
Prepare the doors
Push fit 2 hinges into
each of the doors .
Secure each hinge with
2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.
G
K
3
90
K
Fit the shelf
Insert 4 shelf studs at
the required height.
Lower the shelf down
onto the shelf studs .
H
6
H
Hx 4
6
Make sure that the plastic
sleeve is fully pushed
onto the shelf stud.
H
K
G
G
K
G
G
3
x 2

Small piece of
waste wood
Assembly Instructions
9
Step 12
This will be
the left door
This will be
the right door
Prepare the 2 doors
Important: Please follow
these instructions
carefully.
Lay the doors down
onto a smooth surface.
Important: Carefully
choose which holes you
need to drill.
Check that the holes and
hinges are in the same
place as the diagrams.
Note: We recommend
the use of a small piece
of waste wood, placed
behind the hole while
drilling, to reduce the
possibility of any
breakout.
Using the pilot holes in
the rear face of the door,
. drill through the 2
holes indicated opposite,
using a 2.5mm diameter
drill.
Turn the door over
and open out the 2.5mm
holes that you have just
drilled by drilling back
through them with a
5mm drill.
Note: Drill bits are not
provided.
3
3
3
IMPORTANT
Carefully choose which 2 holes you will need to drill
ONLY drill these 2
holes in ONE door
ONLY drill these 2
holes in ONE door
Small piece of
waste wood
3
3
x 1
x 1