Argos Puerto Rico 658/3129 User manual

4’6 BED
1485mm
2050mm
1100mm
Please spend a short time reading through this leaflet and follow the step-by-step assembly instructions provided. Before commencing assembly, we recommend that you familiarise yourself with the component parts and the instructions. We suggest that you lay out the components and check these against the parts list supplied. CustomerAdvisory Information Assembly Advice
- This product has been produced from natural timber; you may notice some variation in the grain and colour of different
component parts which is normal for furniture produced using natural wood and is not the result of any manufacturing fault.
- The product has been treated with a wax and oil finish to prevent dirt ingress and preserve moisture. On unpacking the
furniture you may notice an odour due to this treatment; this will disappear once the furniture is unpacked and assembled after a period of time.
- This process may leave some staining on the packaging material; please take care to ensure this does not transfer to clothing
or carpeted surfaces during assembly
- Avoid placing the furniture in direct sunlight as this will cause the timber to prematurely age - Use an appropriate furniture polish for natural wood furniture and a dry cloth to clean the product - Please retain packaging materials until assembly is complete; then dispose of packaging materials carefully - We recommend that you assemble the product on a soft/carpeted surface to prevent any damage to panels during assembly - Ensure that all fixings are tight and check these periodically for tightness
- Note: small parts pose a potential safety hazard; ensure that these are securely attached and kept out
of reach of children
Before you start here in some helpful advise Assembly time: 30 minutes

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
TOOLS NEEDED
COMPONENT PARTS
A
10x40 mm
C
EX 8
X 8
X 4
5.0x40 mm
D
BX 52
4.0x16 mm
FX 4
X 2
GX 1 HX 8 JX 2
KX 2 LX 2 MX 2
ø1/4 x 130mm
NX 8
3.5x35 mm
01
02
03
03
05
04
06
26x

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
STEP 1 C
JX 2
X 8
3.5x14 mm
D
GX 1
X 2
A
EX 8
X 4
NX 8
MX 2
KX 2
10x40 mm
5.0x40 mm
ø1/4 x 130mm
01
03
03
05
04
A
E
J
D
M
K
C
STEP 1
STEP 2
02
A
E
N
G
N
G
STEP 2

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
STEP 3 F
BX 52
X 4
3.5x35 mm
220mm
F
4x
42mm
42mm
HX 8
H
STEP 4 LX 2
06
06
L
B
B
L
NO! NO! YES!
Please fix the first slat
adjacent to the headboard
and footboard work towards the middle of the bed using the spacer (L) as shown to ensure correct spacing. Fix all the slats to one siderail first then push the second siderail tight against the slats and fix. Please, retain the allen key (B) and use periodically to
check that all bolts are tight.

Puerto Rico - Double Bed
658/3129
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400 800
Important –Please read these instructions fully before starting assembly
Dimensions
Width - 148.5cm
Depth - 205cm
Height - 110cm
Issue 1 - 17/08/10
658/3136

Safety and Care Advice
Important  Please read these instructions fully before starting assembly
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fttings from the
plastic bags and separate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
We do not
recommend the
use of power
drill/drivers
as this could damage the unit.
Only use hand screwdrivers.
for
inserting screws,
Parts of the assembly will be
easier with 2 people.
Dispose of all packaging
carefully and responsibly.
This product has been produced
from natural timber; you may
notice some variation in the grain
and colour of different component
parts which is normal for furniture
produced using natural wood and
is not the result of any
manufacturing fault.
The product has been treated
with a wax and oil finish to
prevent dirt ingress and preserve
moisture.
On unpacking the
furniture you may notice an
odour due to this treatment;
this will disappear once the
furniture is unpacked and
assembled after a period of time.
This process may leave some
staining on the packaging
material; please take care to
ensure this does not transfer
to clothing or carpeted surfaces
during assembly.
Care and maintenance
Use an appropriate furniture
polish for natural wood
furniture and a dry cloth to
clean the product.
Avoid placing the furniture in
direct sunlight as this will cause
the timber to prematurely age.
From time to time check
that there are no loose
screws on this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.

Components - Panels
Please check you have all the panels listed below
2
1Headboard (110 x 148.5cm)
2Footboard (88 x 148.5cm)
3Side rail x 2 (188 x 11.2cm)
4Centre rail (193.5 x 6.5cm)
6Middle support (28.3 x 6.5cm)
5Slats x 26 (68.2 x 6.5cm)

3
Components - Fittings
Please check you have all the fittings listed below
If you have damaged or missing components,
call the Customer Helpline: 08456 400 800
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
0510 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Tools required
Phillips screwdriver
(medium & large)
Eye protection
(when using a
hammer or glue)
Small
hammer
Ruler/tape
measure
2m
A
D
G
K
B
E
H
L
C
F
J
M
Wooden dowel x 4
N
Metal stud x 4 Wooden
covers x 8
16mm Screw x 8 35mm Screw x 52
40mm Screw x 2 32mm Bolt x 2 130mm Bolt x 8
Nut x 8 Nut x 2 Metal
bracket x 2
Allen key x 1
Spacer x 2

Assembly Instructions
4
Step 1
Fixing metal brackets.
Fix metal brackets into
the pre drilled holes in
the headboard and
footboard using
screws .
Step 2
1
2
Assembling centre rail
and inserting dowels.
centre rail into
the pre drilled holes in
the middle support
using screws .
Insert dowels into the
side rails .
Attach 4
6
B
J
6
D
4
1
2
J
B
D
3
A
3
2x
A
A

4
E
H
Assembly Instructions
5
Step 4
Step 3
Assembling side rails.
Two people are
required for an
easier assembly.
Attach centre rail to
the metal bracket of
headboard using bolt
and nut .
Important:
a: 4
b: With help, assemble
side rails to headboard
using fixings with
the allen key as shown.
3
E
4
H
a:
b:
4
3
1
3
E
H
M
G
F
a:
3
4
2
b:
3
F
M
3
G
F
M
3
a:Attach centre rail to
the metal bracket of
footboard using bolt
and nut .
4
b: With help, assemble
side rails to footboard
using fixings with
the allen key as shown.
3
E
H
M
G
F
2
G

Assembly Instructions
6
Step 6
Step 5
a: Fix metal studs into
the headboard and
footboard at the
dimensions shown.
b: Fix wooden covers
into the
headboard and
footboard as shown.
holes in the
Warning:
While fixing
wooden covers be careful
not to damage them.
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400 800
Assembling slats.
a: Please fix the first slat
at the end of the rail
and work towards the
middle of the bed using
the spacer as shown to
ensure correct spacing.
5
b:a:
5
C
5
N
N
5
5
5
N
L
K
K
L
L
b:a:
222mm
42mm 42mm
K
No! No! Yes!
K
L
1
2
1
2
1
2
C
b: Fix all the slats to
the side rails first using
screws . After, fix all
the slats to the centre rail.
Assembly is complete.