Argos New Hallingford 3 Door 3 Drawer Wardrobe User manual

New Hallingford
3 Door 3 Drawer Wardrobe
Dimensions
Width - 148,8cm
Depth - 60,3cm
Height - 205,7cm
Issue 1 - 10/06/14
Important - Please read these instructions before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
03456 400 800
Assembly Instructions - Please keep for future reference
2745253
2749716
2482279
2448282
2278380
Tip : To prevent damage,
we recommend that you
build your unit on the
carton(s) it was packed in.
DR899153

1
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Safety and Care Advice
Important – Please read these instructionsfully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Care and maintenance
-
•To reduce the
likelihood of
damaging your
product please
ensure that your
• Dispose of all packaging
carefully and responsibly.
power drill is set on a low torque
setting
• Remove all fittings from the
plastic bags and separate them
into their groups.

Components - Panels
Please check you have all the panels listed below
2
Right side
(205.6 x 58cm)
2
P2349b
Left side
(205.6 x 58cm)
1
P2349b
Upright
(196.9 x 57.6cm)
3
P2354b
Door x 2
(199.2 x 48.8cm)
4
P3304
Top/Bottom x 2
(145.8 x 57.7cm)
5
P1350
Upright small
(47.5 x 57.7cm)
6
P2893
Large horizontal
(96.7 x 57.6cm)
7
P1342
Small horizontal
(47.6 x 57.6cm)
8
P1343
Drawer base x 3
(45.4 x 34.9cm)
9
BO33955B
Shelf
(47.6 x 57.6cm)
12
P1348
Plinth front
(145.7 x 14cm)
16
P7336C
Plinth back
(145.7 x 5.4cm)
17
P7337C
Pelmet
(149 x 4.5cm)
18
FA248
Foldy back
(199.3 x 98cm)
14
BO33933
Back
(199.3 x 48.8cm)
13
BO33902
Mirror door small
(151.2 x 48.8cm)
15
PS3324
Drawer wrap x 3
(35 x 46.7 x 10cm)
10
LA1869
Drawer front x 3
(48.8 x 15.7cm)
11
P4308
If you have damaged or missing components, call the
Customer Helpline: 03456 400 800

3
Please check you have all the fittings listed below
40mm Screw x 9
Ruler- Use this ruler to help correctly identify the screws
Tools required
A
10mm Fixing screw drawer x 12
E
20mm Screw x 12
B
24mm locking screw x 32
H
9mm Srew x 6
C
I
Door/Drawer handle x 6
Q
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
V
12.5 mm Screw x 4
F
L-Bracket x 1
15mm Screw x 32
D
Nail x 60
K
15mm Screw x 16
O
Large locking
nut x 26
M
P
Small locking
nut x 6
N
U
Nail holder x 1
L
G
J
Hinge door x 9
R
Runner x 6
S
Hanger rail small x 1
T
Components - Fittings
Phillips screwdriver
(medium & large)
Flatblade screwdriver
Small
hammer
Ruler/tape
measure
Drill
Eye protection
(when using a
hammer or drill)
5mm Suitable drill bit
GR1975 PM1873
Hanger rail large x 1
PM1884
FK1268FK1269
Hinge back x 9
FK1324
FK1012
FK1010
FK1011
FK1301
FK1981
FK1980
FK1400
FK1311
FK1235
Hanger rail support x 4 Board carrier x 4
FK1217
FK1309
Peg x 2
FK1234
FA1515 FK1419
FK1207
PM16951
2.5mm Suitable drill bit
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Stairs
Piercer Scissors
(medium)
(small)
Spirit level
Setsquare
W
Drawerbase support x 6
FK1250
X
Wall plug and parkerscrew x 1
ZF99936

4
Assembly Instructions
Step 1
Drawer assembly x 3
a: Insert two small locking
nuts Jinto drawer wrap
0.
Make sure the ‘arrow’ on
Jis pointing towards the
hole in the edge of 0
b: Screw 24mm locking
screws Hinto holes
shown on back of drawer
front !.
Make sure 24mm locking
screws Hare tightened
right up against drawer
front !.
H
10
J
J
11
H
H
H
a:
b
9
10
c:
11
c: Slide drawer base 9
into grooves shown on
drawer wrap 0.

5
Assembly Instructions
Step 1 - continued
Attaching runners
d: Turn the drawer wrap
assembly over and push
onto drawer front !. Use
a philips or flatblade
screwdriver, that is a good
fit, to turn small locking nut
Jas far as it will go - more
than 1/2 turn.
H
d
J
e:
11
T
11
B
B
Step 2
a: Slide top of runners R
foreward and fix on upright
3as shown using 10mm
fixing screw drawer E.
Finished
front edge
a:
R
R
R
R
E
E
E
E
3
3
J
J
e: Fix drawer handle T
onto drawer front !using
30mm screw B.
Turn over drawer and
slide Drawerbase supports
Win corner as shown and
fix them, using the attached
screws .
W
W

6
Assembly Instructions
Finished
front edge
b
E
R
R
R
3
R
E
E
E
3
O
O
O
O
O
O
OO
b
a:
Step 2 - continuedStep 2 - continued
b: Slide top of runners R
back.
Fix through 3rd hole of
runner Rand pre-drilled
holes of upright 3using
10mm fixing screw drawer
E.
Fix through 1st and 9th
hole of runners Rusing
15mm screw O.
Note: there are no pre-
drilled holes for 15mm
screw O.
Repeat aand bon
upright small 6.
Step 3
Insert fittings
a: Screw 24mm locking
screw Hinto upright 3.
Note: Insert 24mm locking
screw Has far as shown.
Do not over tighten.
Attach hinge back Ponto
upright 3.
H
3
H
H
H
H
H
H
3
3
M
M
3
Attach hanger rail
support Musing 12.5mm
screw Fonto uprigh 3.
Flip panel
F
F
3
P
P
P
P
M
F
Finished
front edge
N
N
Finished
front edge
b: Put board carrier N
into upright 3.
Attach hanger rail
support Musing 12.5mm
screw Fonto upright 3.

7
Assembly Instructions
Step 4
Attaching panels
Attaching plinths
Align the sides of plinth
front ^with bottom 5as
shown and attach using
40mm screw A.
Note: there are no
predrilled holes for
40mm screw aA.
Note: top and bottom
panels 5are identical.
Only prepare one of the
panels at this stage. This
will be the bottom panel
Repeat with plinth back
&.
A
Step 6
Position upright 3onto
bottom panel 5.
Insert two Large locking nuts
Iinto upright as shown.
Use a screwdriver to turn
locking nuts Iclockwise to
lock.
Top side
A
A
A
A
A
5
16
17
Step 5
Insert locking screws
Screw 24mm locking
screw Hinto bottom 5.
Top side
5
M
M
Unfinished
back edge
H
H
H
H
I
I
I
3
5
I

8
Step 7Step
Insert locking screws
Screw 24mm locking
screw Hinto top 5.
Step 8
Attaching panels
Two people are needed
here.
Position top 5, large
horizontal 7and small
horizontal 8onto upright
3.
Insert two Large locking
nuts Iinto upright 3, 3 in
large horizontal 7and 2 in
small 8horizontal where
shown.
Use a screwdriver to turn
locking nuts Iclockwise to
lock.
H
H
5
I
I
I
I
I
I
I
5
7
8
3
I
I
Step 9
H
H
H
Insert locking screws
Screw 24mm locking
screw Hinto upright
smal 6.
6
Unfinished
back edge
Unfinished
back edge
I
I
I
I
Assembly Instructions

9
Assembly Instructions
Step 10
Step 11
M
MI
I
I
I
Attaching panels
Two people are needed
here.
Position upright small 6
onto bottom 5and small
horizontal 8.
Insert two Large locking
nuts Iinto upright small
6and small horizontal 8
where shown.
Use a screwdriver to turn
locking nuts Iclockwise to
lock.
8
5
Finished
front edge
H
H
H
H
H
H
H
H
H
H
H
P
P
P
P
P
P
M
F
M
F
Screw 24mm locking
screws Hinto left side 1
and right side 2.
Note: Insert 24mm locking
screw Has far as shown.
Do not over tighten.
Attach hinge back Ponto
left side 1and right side
2.
Attach hanger rail
support Musing 12.5mm
screw Fonto left side 1
and right side 2.
2
1
H
12
1
P
2
N
Insert fittings
Put board carrier Ninto
right side 2.
M
3F
N
6
I
I
I
I