Argos Dalton 228/5713 User manual

MADE IN
BRITAIN
Dimensions
Width - 84.5cm
Depth - 50cm
Height - 182cm
Dalton - 2 Door Robe
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 17/04/14
Important - Please read these instructions fully before starting assembly
ALR3040
228/5713
248/4040
245/8186

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 44.5kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
12
4
80%
x 3
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
6
Left End (DF708)
(1800 x 465mm)
Top (DF710)
(843 x 496mm)
Base (DF715)
(809 x 457mm)
Rail (DF713)
(809 x 80mm) x 2
Palister (DF714)
(1800 x 88mm) x 2
5
3
Back (DF716)
(1731 x 835mm)
Right End (DF709)
(1800 x 465mm)
8Door (DF711)
(1714 x 328mm) x 2
9
Hanging Rail (FHR801)
(801mm long)
7

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 10
B
Metal dowel (F901) x 22
C
D E F
G H I
L
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
M
J K
N
Large locking
nut (F900) x 22
Nail (F51) x 34 19mm Screw (F461) x 4
Plastic Nail (F91) x 4
13mm Screw (F79) x 1 13mm Screw (F63) x 14 Shelf stud (F110) x 2
Bracket (F327) x 1 Handle (F287) x 2
Rail holder
(F1014) x 2
Hinge Plate
(F325) x 6
Hinge Arm
(F324) x 6
Tools required
Rule
Scissors
Spirit
level
Hammer Bradawl
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Step
ladder
Electric drill
(only use
when drilling
into walls)
Square
mm 10 20 30 40 50 60 70 80 90 100 mm 10 20 30 40 50 60 70 80 90 100

A
A
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
80%
x 3
Prepare the left end
Tap a wooden dowel
into the left end .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 7 large locking
nuts into the left end
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Screw 4 metal dowels
into the left end .
Note: Tighten the metal
dowels up fully against
the panels.
Push a rail holder into
the left end . Make
sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
B
1
C
1
10mm
A
1
A
C
CC
C
C
C
C
C
C
B
B
B
B
B
Prepare the right end
Tap a wooden dowel
into the right end .
Insert 7 large locking
nuts into the
right end .
Screw 4 metal dowels
into the right end .
Push a rail holder into
the right end and
then secure with screw .
B
2
C
2
2
A
Step 2
C
C
C
C
C
C
C
B
B
B
B
1
2
J
H
J
1
H
J
2
H
J
H

Assembly Instructions
5
Prepare the 2 pallisters
a: Tap 2 wooden dowels
. into the top end of 1
of the pallisters .
Fit 3 hinge plates to
this pallister using
the upper pair of holes.
Screw 5 metal dowels
into the pallister .
b: Tap 2 wooden dowels
. into the bottom end
of the other pallister .
Fit 3 hinge plates to
this pallister using
the lower pair of holes.
Screw 5 metal dowels
into the pallister .
Step 3
B
B
B
B
B
M
M
M
B
B
B
B
B
M
M
M
A
6
6
6
Upper pair of holes Dowels this end
Lower pair of holes
A
A
Dowels this end
A
A
b:
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back .
Note: Nails should be
spaced about 150mm
apart.
Stand the unit up for
the next step.
a:
M
B
A
6
6
6
M
B
M
M
6
6

Assembly Instructions
6
Step 4
Fit a pallister to the
left end
Push the correct pallister
. onto the left end .
Use a screwdriver to
tighten the 5 large
locking nuts fitted to
the left end .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
6 1
1
C
B
C
C
Dowels this end
6
1
Dowels this end
6
2
Step 5
Fit a pallister to the
right end
Push the correct pallister
. onto the right end .
Use a screwdriver to
tighten the 5 large
locking nuts fitted to
the right end .
6 2
2
C

Finished
front edge
A
Prepare the base
Insert 4 large locking
nuts into the base .
C4
Assembly Instructions
7
Step 6
C
C
C
C
Finished
front edge
4
Step 7
Fit the base to the
right end
Push the base onto
the right end .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the base .
Step 8
4
2
4
C
C
C
A
Prepare the 2 rails
Insert 2 large locking
nuts into each of the
2 rails .
Tap 2 wooden dowels
into each of the 2 rails .
C
5
5
A
5
x 2
4
2

Assembly Instructions
8
Step 9
Fit the rails to the
right end
Push the 2 rails onto
the right end .
Use a screwdriver to
tighten the large locking
nut fitted to each of
the rails .
Step 10
2
5
5
5
2
C
5
Fit the left end
Push the left end
onto the assembly.
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the base and the 2
rails .
1
C
5
5
5
1
4
4

Prepare the top
Screw 4 metal dowels
into the top .
Assembly Instructions
9
Step 11
B
B
B
B
Finished
front edge
B
3
Step 12
Fit the top
Push the top onto
the assembly.
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the left end and right
end .
3
C
2
1
2
1
1
2
Step 13
Fit the 4 plastic nails
Tap 2 plastic nails
into the bottom edge of
each of the sides and
. .
E
1
2
E
EE
E
3
Finished
front edge