Argos Seville User manual

Assembly Instructions - Please keep for future reference
Ruler - Use this ruler to help correctly identify the screws
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
MADE IN
BRITAIN
If you need help or have damaged or missing parts, call the Customer Helpline: 0870 112 1928
or email: [email protected] (quoting your original order number)
Important - Please read these instructions fully before starting assembly
Dimensions
Width - 69.5cm
Depth - 49.5cm
Height - 175.5cm
Seville - 2 Door Robe
Issue 1 - 08/10/13
ALR2906
166/8843
187/8633
144/6508
157/4803

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 40kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.

2
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email:
[email protected] (quoting your original order number
and the reference numbers below)
1
80%
x 2
Top (D2482A)
(663 x 495mm)
Base (D2485A)
(663 x 480mm)
Plinth (D2486A)
(663 x 80mm)
2
Door (D2487A)
(1652 x 327mm) x 2
Back (X1666-689)
(1666 x 689mm)
Left Side (D2483A)
(1753 x 496mm)
Right Side (D2484A)
(1753 x 496mm)
3
4
5
7
8
Hanging Rail (FHR653)
(653mm long)
6

Glue Safety - Take care when using glue, please follow the advice below
Skin contact: Remove contami-
nation by washing with soap and
water. This procedure should be
followed prior to aeting and
drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
3
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• From time to time check that
there are no loose screws on
this unit.
Rule
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Tools required
Rule
ScissorsSquare
Spirit
level
Hammer Bradawl
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Step
ladder
Ruler - Use this ruler to help correctly identify the screws
Electric drill
(only use
when drilling
into walls)
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email:
[email protected] (quoting your original order number
and the reference numbers below)
A
Wooden dowel (F22) x 6
B C
D E F
G H I
Nail (F51) x 32 40mm Screw (F910) x 10
J K
Bracket (F327) x 1
13mm Screw (F79) x 1
Hinge plate
(F523) x 6 Hinge (F522) x 6
13mm Screw (F63) x 14
Rail holder
(F1014) x 2 Handle (F300) x 2
25mm Screw (F95) x 2

4
F
Step 1
Assembly Instructions
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email:
[email protected] (quoting your original order number
and the reference numbers below)
Finished
front edge
Step 2
1
J
Prepare the left side
Push a rail holder into
the left side . Make
sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
Fit 3 hinge plates onto
the left side , making
sure that the slot is
facing towards the
finished front edge.
H
1
J
1
Prepare the right side
Push a rail holder into
the right side . Make
sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
Fit 3 hinge plates onto
the right side , making
sure that the slot is
facing towards the
finished front edge.
Step 3
H
2
J
2
2
J
10mm
A
Prepare the top and
base
Tap 2 wooden dowels
into the top .
Tap 2 wooden dowels
into the base .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
A
A
3
4
J
J
J
H
F
1
F
J
J
J
H
F
2
Finished
front edge
F
A
A
3
plain chipboard surface
4
A
A

C
Finished
front edge
Finished
front edge
Finished
front edge
C
C
C
C
Assembly Instructions
5
Step 4
Step 5
Fit the top and the
base to the right side
Push the top and the
base onto the right
side and secure them
using 4 screws .
3
4
2
C
A
Prepare the plinth
Tap 2 wooden dowels
into the plinth .
5
Step 6
Fit the plinth
Push the plinth onto
the right side and
secure it using screw .
5
2
C
3
4
2
A
A
Plain chipboard
5
2
5Note: Support the plinth
until the left side has been
fitted in the next step.
plain chipboard surface

Finished
front edge
Assembly Instructions
6
Step 7
Fit the left side
Push the left side
onto the assembly and
secure it using 5 screws
. . C
1
1
C
C
C
C
C
Step 8
b:
B
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back .
Note: Nails should
be spaced about
150mm apart.
Stand the unit up for
the next step.
8
B
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
8y
y
x
x
8

Assembly Instructions
7
Step 9
Step 10
6
H
Fit the hanging rail
Push hanging rail into
the rail holders fitted
to the side panels.
6
H
Prepare the 2 doors
Push fit 3 hinges into
each of the the doors
Secure each hinge with
2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.
F
K
7
90
K
.x 2
6
K
F
F
K
F
F
K
F
F
7

Assembly Instructions
8
Step 11
Fit doors and handles
Note: The easiest way to
attach each door is
to fit the top hinge first,
then align and fit the
other hinges.
a: Push the hinge
onto the front part of the
hinge plate .
The recess at the bottom
of screw B goes into the
slot in the hinge plate.
b: Keep the hinge
FLAT against the hinge
plate as you slide it
across as far as it will go.
Tighten screw A.
c: The hinge must be
flat against the hinge
plate prior to any
adjustment.
d: The hinge must
NOT be AT AN ANGLE
to the hinge plate
when assembled.
This would indicate that
the recess at the bottom
of screw B had not
located in the slot in the
hinge plate and the hinge
would not be secure.
Remove the hinge from
the hinge plate and then
re-assemble being
careful to follow
instructions a-c.
e: Attach a handle to
each door using
screw .
K
K
K
J
J
J
K
J
I
D
7
7
a: b:
c: d:
J
K
J
J
B
J
K
K
K
A
K
J
B
e:
I
I
D
7
7

Assembly Instructions
9
Step 12
b:
c:
d:
a:
Adjust the doors if
needed
a: Before adjusting the
doors, use a spirit level
to check the base (or
top) of the unit is level,
front-to-back and
side-to-side in the 3
positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level
BEFORE making any
adjustment to the hinges,
as shown.
b: Height adjustment.
Loosen screws A on
hinge plates and move
door up or down as
required.
Retighten screw A.
c: Forward and Back
adjustment.
Loosen screw B on hinge
plate and move door in
or out as required.
Retighten screw B.
d: Sideways
adjustment.
To move door ‘out’
loosen screw C.
To move door ‘in’ tighten
screw C.
A
A
B
C