Argos Wow Raye Wooden Chair User manual

322/5837
345/6307
Wow Raye Wooden Chair
Assembly Instructions - Please keep for future reference
Issue 1 - 08/10/14
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
Width - 41.5cm
Depth - 50cm
Height - 85cm
Dimensions

1
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product, this
could cause damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• Do not stand on the chair.
• Do not use this chair as step
ladder.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Unit weight: 3.04kgs.
• Maximum safe weight of user:
110kgs.
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Care and maintenance
Handy Hints
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the
bolts.
• Regularly check and ensure
that all bolts and fittings are
tightend properly.

2
Note: The quantities below are the correct amount to complete the assembly of one chair.
Components - Parts
Please check you have all the parts listed below
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly of one chair. In some cases
more fittings may be supplied than are required.
AB
M6 x 70mm Bolt x 8 Wooden dowel x 16
D
Allen key x 1
Components - Fittings
1Left leg frame
(43 x 85 x 3cm)
2Right leg frame
(43 x 85 x 3cm)
5Seat
(41.5 x 41 x 1.3cm)
6Seat back rail
(27 x 5 x 1.8cm)
7Seat front rail
(34 x 5 x 1.8cm)
8Stretcher
(32 x 2.8 x 1.8cm)
3Back rest top rail
(27 x 5 x 2.5cm)
4Back rest lower rail
(27 x 5 x 2.5cm)
If you have damaged or missing components,
call the Customer Helpline: 0345 6400800
C
Screw x 4
Tools required
Crosshead screwdriver

3
Attaching back rest and
rails
Position the backrest top
rail , backrest lower
rail , seat back rail
and seat front rail on
the right leg frame
and insert the wooden
dowels into holes as
shown.
Important:
Make sure to
position the front
and back rails
with the smaller
screw holes up as
shown.
Step 2
Fitting dowels
Insert wooden dowels
into holes on the
backrest top rail ,
backrest lower rail ,
seat back rail and
seat front rail as
shown.
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
Assembly Instructions
Step 1
2
2
64
7
2
34
3
3
6
7
4
4
3
7
6
6
7
3
B
B
B
B
4
Smaller
holes up

4
Step 4
Securing the leg frames
a: Secure the leg frame
using bolts as
shown and tighten using
allen key but do not
fully tighten at this stage.
Attach the stretcher
between the legs &
as shown and secure
using bolts .
Fully tighten bolts using
allen key .
Important:
Make sure to
position the
stretcher at an
angle as shown in
the inset diagram.
b: Carefully turn the
chair frame on the other
side to secure the leg
frame and the
stretcher using bolts
as shown and tighten
using allen key .
A
A
A
D
D
D
1
8
8
1 2
2
8
2
1
3 4
6
7
1
3
A
AAA
A
34
6
7
8
8
1
2
A
A
A
A
a:
b:
Assembly Instructions
Attaching left leg
Carefully position the left
leg as shown and with
a help holding the rails
and back rest, attach the
left leg by inserting the
wooden dowels into
holes as shown.
Step 3
1
2
34
6
7
1
A
8
1
1
8
Back
Front

5
Assembly Instructions
Assembly is complete.
Attaching seat
Position the seat face
down on a flat and raised
surface such as a table.
Position the chair frame
on the seat as shown
then fix seat back rail
and seat front rail to
seat using screws .
Tighten screws using a
crosshead screwdriver.
Important:
Make sure to
correctly position
the seat as shown
in the diagram.
Carefully position the
chair frame upright.
Step 5
6
6
7
5
5
5
6
7
C
C
CC
C
C
back of
the seat
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800

6
Please note that the product you have purchased is a natural
living timber.
Just like nature itself, wood varies in shape and colour. Knots,
vein patterns, resin pockets and colour differences contribute to
giving the piece of furniture its beauty and form - a natural part of
solid wood.
Although the tree has been cut down and dried, it is still alive and
therefore will react to high and low temperatures, light, humidity,
drought and time.
In cold and dry periods, the wood contracts which may lead to
small cracks in the piece of furniture. The reverse happens in
warm and humid periods where the wood expands and this may
result in slight unevenness.
The colour of the wood also changes with time, particularly if the
furniture is placed in a light place. This is a natural process and
part of owning a piece of furniture made of solid wood.
Any flexing that has occurred during transport will re-correct itself
once this product is correctly assembled.
Tighten all joints of the furniture after six months.
Please keep these instructions in a safe place for future use.
Dear Customer