Argos Betsy 404/4842 User manual

Assembly Instructions – Please keep for future reference
Important – Please read these instructions fully before starting assembly
Length - 201cm
Width - 145cm
Height - 120cm
If you need help or have damaged or missing parts, call the Customer Helpline: 0345 6400 800
Issue 1 - 25/03/15
Betsy 4'6 and 5' Bed
Dimensions (5')
Length - 211cm
Width - 160cm
Height - 120cm
Dimensions (4'6)
404/4842
400/8792

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
1
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Dispose of all packaging
carefully and responsibly.
• Place the product on flat and
steady surface during use.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Keep these instructions for
further use.
• To ensure an easier assembly,
we strongly advise that all
fittings are only finger tightened
during initial assembly. Only
upon completion of the
assembly should all fixing points
be fully tightened.
Care and maintenance

Please check you have all the parts listed below
Components - Parts
2
Headboard panel (145 x 80cm) (160 x 80cm)
1
2
Footboard panel (145 x 80cm) (160 x 80cm)
Side rail x 2 (193.7 x 10.8cm) (203.7 x 10.8cm)
4
3
End support x 2 (136.5 x 4cm) (151.7 x 4cm)
5
Central support (183 x 9cm) (187.8 x 9cm)
6
8Bentwood slat x 32Support leg x 2
(24 x Ø2.5cm)
7
If you have damaged or missing components,
call the Customer Helpline: 0345 6400 800
Headboard post x 2
(45 x Ø3.8cm)

Components - Fittings
A
Rubber washer x 8
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
Plain washer x 22
Allen key x 2
If you have damaged or missing components,
call the Customer Helpline: 0345 6400 800
BC
D E F
G
Nut x 4
3
25mm Allen screw x 415mm Allen screw x 12
HJ
K
45mm Allen screw x 2 Central plastic cap x 16
Plastic cap x 32
Ruler - Use this ruler to help correctly identify the screws
0510 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Tools required
0
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150
1 2 3 4 5 6
Ruler/tape
measure
32mm Allen screw x 4

Step 1
Assembly Instructions
Assembling posts
Place headboard panel
face down onto a
clean flat surface.
Note: Fixing holes for
posts should be facing
up.
Secure headboard posts
to headboard panel
using fixings
and .
A
2
1
B
1
4
Step 2
Front
Back A
B
Step 2
Assembling side rails
a: With help, assemble
side rails to the
headboard using fixings
, , and .
Note: Ensure the metal
brackets are at the
bottom as shown.
b: Assemble footboard
to the side rails using
fixings and .
3
BC E
BD E F
BD
F
E
B
3
4
4
2
E
a:
b:
C
4
Brackets at bottom
A
B
2
1
3
2
4
4

Assembly Instructions
Step 3
5
5
5
4
A
B
Step 4
G
BA
A
B
B
6
7
5
5
Holes inside
4
7
Securing end supports
Locate end supports
into the metal brackets
on the inside of side rails
.
Note: Ensure the fixing
holes are on the inside as
shown.
Secure using fixings
and .
5
4
B
A
Assembling central
support
Locate central support
in between end
supports and
secure using fixings
and .
Assemble support legs
to the underside of
central support using
fixings and .
6
5
A
B
7
6
BG

Assembly Instructions
Step 5
6
Assembly is complete.
K
J
J
K
K
8
8
8
8
4
6
Attaching slat caps
Assemble plastic caps
onto one end of
bentwood slats .
a: Fit plastic caps
into the slotted holes
in side rails as shown.
b: Fit bentwood slats
into both sides of
central plastic caps
before pushing caps
into central support .
8
8
6
8
a:
b:
J
J
K
8
8
If you need help or have damaged or missing parts, call the Customer Helpline: 0345 6400 800
Home Retail Group. 489-499 Avebury Boulevard. Saxon Gate West. Central Milton Keynes. MK9 2NW
4
K