Argos Malvern 395/6632 User manual

MADE IN
BRITAIN
Dimensions
Width - 44.5cm
Depth - 39.5cm
Height - 69.5cm
Malvern - 3 Drawer Bedside
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 1 - 11/05/15
Important - Please read these instructions fully before starting assembly
ALR3203
395/6632
390/9940

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 19kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Tools required
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver

Components - Panels
Please check you have all the panels listed below
2
1 2 3
80%
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
5 6
Left Side (DF4056)
(630 X 374mm)
Right Side (DF4057)
(630 X 374mm)
Top (DF87)
(445 x 392mm)
Base (DF88)
(437 x 374mm)
Top Drawer Back
(W354-124)
(354 x 124mm) x 2
Top Left Drawer
Side (W370-124LH)
(370 x 124mm) x 2
Top Right Drawer
Side (W370-124RH)
(370 x 124mm) x 2
7
Bottom Right Drawer
Side (W370-165RH)
(370 x 165mm)
Bottom Drawer Back
(W354-165)
(354 x 165mm)
Back (X663-429)
(663 x 429mm)
4
8
9 10 11 12
Bottom Left Drawer
Side (W370-165LH)
(370 x 165mm)
13
14
Top Drawer
Front (DF89)
(428 x 195mm) x 2
Bottom Drawer
Front (DF90)
(428 x 243mm)
Drawer Base (T366-366)
(366 x 366mm) x 3

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
A B
D E F
G H I
C
Metal dowel (F901) x 10
Wooden dowel (F22) x 8
Small locking
nut (F3) x 6 Large locking
nut (F900) x 4
40mm Screw (F910) x 4
OR Runner (F160) x 3
b
L Runner (F161) x 3
Oc
L Runner (F159) x 3
Oa
R Runner (F162) x 3
Od
350mm long
J
13mm Screw (F63) x 18
Knock-in Peg (F171GY) x 12
K
Wedgefix (F639) x 6
L
M N
Nail (F51) x 14
38mm Screw (F81) x 8
9mm Screw (F73) x 18
19mm Screw (F461) x 6
Foot
(F233) x 4
Handle (FBARHANDLE) x 3

5
5
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
x 2
x 2
x 2
x 2
A
A
B
B
B
B
67
Step 2
Prepare the 2 top
drawer fronts
Screw 2 metal dowels
into each of the top
drawer fronts .
Note: Tighten the metal
dowels up fully against
the panels.
A
5
Prepare the top
drawer sides
Insert a small locking
nut into the hole
shown on the top left
drawer side and the
top right drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
B
6
7
Attach the top drawer
sides to the top
drawer fronts
Push the top left drawer
sides . and top right
drawer sides . onto
the back of the top
drawer fronts .
Turn the small locking
nuts on the top left
drawer side and top
right drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
6
7
5
B
B
6
7
6
7
A
A

5
Assembly Instructions
5
Step 4
J
J
Fit the drawer base
Slide the drawer base
down the grooves in the
top drawer sides and
. and down into the
groove in the top drawer
front .
Step 5
Fit the top drawer back
Fit the top drawer back
. between the top
drawer sides and .
Make sure that the
drawer base fits into
the groove in the top
drawer back .
Hold the top drawer
back in position and
tap the knock-in pegs
through the holes in the
top drawer sides and
. .
Step 6
13
6
7
5
8
6 7
13
8
8
J
Attach the handles
Attach a handle to
each of the top drawer
fronts using screws
. .
M
G
5
6
7
Step 7
Fit the wedgefixes
Turn the 2 top drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
K
x 2
x 2
x 2
J
J
x 2
K
KK
13
6
8
6
7
13
7
G
G
M
5

9
Assembly Instructions
6
Step 8
A
B
A
B
BBB
10 11
Step 9
Prepare the bottom
drawer front
Screw 2 metal dowels
into the bottom drawer
front .
A
9
Prepare the bottom
drawer sides
Insert a small locking
nut into the hole
shown on the bottom left
drawer side and the
bottom right drawer side
. .
Step 10
B
10
11
Attach the bottom
drawer sides to the
bottom drawer front
Push the bottom left
drawer side . and
bottom right drawer side
. onto the back of the
bottom drawer front .
Turn the small locking
nuts on the bottom
left drawer side and
bottom right drawer side
. .
10
11
9
B
10
11
11
10
A
A
9

9
J
J
Assembly Instructions
7
Step 11
Fit the wedgefixes
Turn the drawer
assembly over and slide
2 wedgefixes into the
front and back grooves,
as shown, and tighten up
the screws.
Fit the drawer base
Slide the drawer base
down the grooves in the
bottom drawer sides
and and down into
the groove in the bottom
drawer front .
Step 12
Step 13
13
10
11
9
13
Attach the handle
Attach the handle to
the bottom drawer front
. using screws .
G
9
M
Fit the bottom drawer
back
Fit the bottom drawer
back between the
bottom drawer sides
and .
Make sure that the
drawer base fits into
the groove in the bottom
drawer back .
Hold the bottom drawer
back in position and
tap the knock-in pegs
through the holes in the
bottom drawer sides
and .
12
10
11
13
12
12
J
10
11
J
J
Step 14
KK
11
10
11
10
12
13
9
K
K
G
G
M

Assembly Instructions
8
Step 15
Fit runners to the 2
top drawers
Fit runner , marked
with ‘R’, to the bottom
edge of the top right
drawer side , as
shown, making sure that
it is pushed up against
the back of the top
drawer front . Use a
bradawl to mark the
fixing positions, then
secure with 2 screws .
Fit runner , marked
‘L’, to the bottom edge
of the top left drawer
side using the same
method.
6
O d
7
5
H
O c
O d
Runners must be
pushed up against
the drawer front
R
R
H
H
L
O c
L
H
H
7
O d
Runners must be
pushed up against
the drawer front
R
R
H
H
L
O c
L
H
H
6
5
Step 16
Fit runners to the
bottom drawer
Fit runner , marked
with ‘R’, to the bottom
edge of the bottom right
drawer side , as
shown, making sure that
it is pushed up against
the back of the bottom
drawer front . Use a
bradawl to mark the
fixing positions, then
secure with 2 screws .
Fit runner , marked
‘L’, to the bottom edge
of the bottom left drawer
side using the same
method.
10
O d
11
9
H
O c
11
10
9
x 2

Finished
front edge D
D
Assembly Instructions
9
Step 17
O a
I I
1st
screw
2nd
screw I
3rd
screw
Finished
front edge
O a
H
Finished
front edge
a:
b:
Prepare the left side
a: Fit 3 runners to
the left side .
The 1st screw uses
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the 2nd hole in at the top
of the runner .
c: Tap 4 wooden
dowels into the left
side .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 2 large locking
nuts into the left side
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
O a
1
I
I
H
C
1
D
1
O a
I
O a
I
O a
I
O a
H
H
H
c:
I
I
I
I
I
I
C
D
D
1
1
1
C
C
C
10mm
D
Finished
front edge
Finished
front edge