Arjo AtmosAir 9000A User manual

Bedienungsanleitung · Gebruiksaanwijzing · Manuel d’utilisation · Istruzioni per l’uso
Instrucciones de uso · Brugsvejledning · Instruktioner för användning
,QVWUXo}HVGHXWLOL]DomRā.XOODQÕP7DOLPDWODUÕāȅįȘȖȓİȢȤȡȒıȘȢā.l\WW|RKMHHW
Bruksanvisning
EN · DE · NL · FR · IT · ES · DA · SV · PT · TR · EL · FI · NO
AtmosAir 9000A
Mattress Replacement System
INSTRUCTIONS FOR USE
416412 Rev 2 • 09/2019

ii
WARNING
To avoid injury, always read this Instructions for Use and accompanied
documents before using the product.
Mandatory to read the Instructions for Use.
Design Policy and Copyright
® and ™ are trademarks belonging to the Arjo group of companies.
© Arjo 2019.
As our policy is one of continuous improvement, we reserve the right to modify
designs without prior notice.
The content of this publication may not be copied either whole or in part without
the consent of Arjo.

iii
DISCLAIMER OF WARRANTY AND LIMITATION OF REMEDY
ARJO HEREBY DISCLAIMS ALL EXPRESS OR IMPLIED WARRANTIES,
INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ON THE ARJO
PRODUCT(S) DESCRIBED IN THIS PUBLICATION. ANY WRITTEN WARRANTY
OFFERED BY ARJO SHALL BE EXPRESSLY SET FORTH IN THIS PUBLICATION
OR INCLUDED WITH THE PRODUCT. UNDER NO CIRCUMSTANCES SHALL
ARJO BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES AND EXPENSES, INCLUDING DAMAGES OR INJURY TO PERSON
OR PROPERTY, DUE IN WHOLE OR IN PART TO THE USE OF THE PRODUCT
OTHER THAN THOSE FOR WHICH DISCLAIMER OF WARRANTY OR LIMITATION
OF LIABILITY IS EXPRESSLY PROHIBITED BY SPECIFIC, APPLICABLE LAW.
NO PERSON HAS THE AUTHORITY TO BIND ARJO TO ANY REPRESENTATION
OR WARRANTY EXCEPT AS SPECIFICALLY SET FORTH IN THIS PARAGRAPH.
'HVFULSWLRQVRUVSHFL¿FDWLRQVLQ$UMRSULQWHGPDWWHULQFOXGLQJWKLVSXEOLFDWLRQDUHPHDQW
solely to generally describe the product at the time of manufacture and do not constitute
any express warranties except as set forth in the written limited warranty included in this
publication or with this product. Information in this publication may be subject to change
at any time. Contact Arjo for updates.
Important Information For Users
In order for Arjo products to perform properly, Arjo recommends the following conditions.
Failure to comply with these conditions will void any applicable warranties.
• Use this product only in accordance with these instructions and applicable product
labeling.
• $VVHPEO\RSHUDWLRQVH[WHQVLRQVUHDGMXVWPHQWVPRGL¿FDWLRQVWHFKQLFDO
PDLQWHQDQFHRUUHSDLUVPXVWEHSHUIRUPHGE\TXDOL¿HGSHUVRQQHODXWKRUL]HGE\$UMR
Contact Arjo for information regarding maintenance and repair.
• If applicable, ensure the electrical installation of the room complies with the
appropriate national / local electrical wiring standards.
Specic indications, contraindications, warnings, precautions and safety information
exist for Arjo’s therapeutic support systems. It is important for users to read and
familiarize themselves with these instructions and to consult the treating physician
prior to patient placement and product use. Individual patient conditions may vary.
Notice
7KLVSURGXFWKDVEHHQFRQ¿JXUHGIURPWKHPDQXIDFWXUHUWRPHHWVSHFL¿FYROWDJH
UHTXLUHPHQWV5HIHUWRWKHSURGXFWLQIRUPDWLRQODEHOIRUVSHFL¿FYROWDJH

iv
Intentionally left blank

1
Table Of Contents
Introduction .......................................................................................................2
Indications ..................................................................................................................... 2
Contraindications ........................................................................................................... 2
Risks and Precautions ................................................................................................... 2
Safety Information ......................................................................................................... 3
Serious Incident ............................................................................................................. 4
Preparation for Use ..........................................................................................5
Mattress Installation .........................................................................................5
AtmosAir 9000A MRS .................................................................................................... 5
AtmosAir Pump Installation ........................................................................................... 6
LED Indicators .............................................................................................................. 6
Patient Placement and Nursing Care ............................................................................ 7
Alternating Pressure ..................................................................................................... 7
CPR ............................................................................................................................... 8
Transport Mode ............................................................................................................. 8
Skin Care ....................................................................................................................... 8
Incontinence / Drainage ................................................................................................ 8
General Operation ......................................................................................................... 8
Care and Cleaning ............................................................................................9
Fire Barrier .................................................................................................................... 9
Cover Cleaning ............................................................................................................. 9
Cleaning AtmosAir Pump and Tubes ......................................................................... 10
Preventive Maintenance Schedule................................................................11
Daily Cleaning ..............................................................................................................11
Weekly Cleaning ...........................................................................................................11
Inspection / System Checks ........................................................................................11
Troubleshooting ............................................................................................12
Parts Diagram - AtmosAir with SAT 9000A ...................................................13
Parts Diagram - AtmosAir Pump 9000A .......................................................14
Replacement Parts .........................................................................................15
Specifications .................................................................................................16
Electromagnetic Compatibility ......................................................................17
Symbols Used .................................................................................................20
Customer Contact Information ......................................................................21

2
Introduction
It is recommended that all sections of this User Guide be read prior to product use.
Carefully review the Contraindications, Safety Information and Risks and Precautions
sections prior to placing a patient on any AtmosAir™ with SAT™ Mattress Replacement
System (MRS).
Caregivers should review this information with the patient and the patient's family and / or
legal guardian. Save this User Guide in an easily accessible location for quick reference.
The AtmosAir 9000A MRS comes in a wide variety of lengths and widths to support
various customer requirements. Contact an Arjo representative for additional product
information.
Indications
AtmosAir™ 9000A Mattress Replacement System (MRS) is intended to treat and prevent
all categories of pressure ulcers.
Contraindications
• unstable vertebral fracture
• cervical and skeletal traction
Risks and Precautions
Transfer – Standard precautions should be taken during patient transfer.
Side Rails and Restraints – WARNING: Use or non-use of restraints, including side rails,
can be critical to patient safety. Serious or fatal injury can result from the use (potential
entrapment) or non-use (potential patient falls) of side rails or other restraints. See related
Safety Information.
• The AtmosAir 9000A is a mattress replacement system - remove all
other mattress components.
• To ensure compliance with IEC 60601-2-52:2010, an approved Arjo
mattress should be used.
• The user is responsible for validating other combinations of bed and
mattress to ensure compliance with IEC 60601-2-52:2010.
• For more information on suitable beds, contact your local Arjo o󰀩ce
or approved distributor.
Patient Migration –6SHFLDOW\VXUIDFHVKDYHGLႇHUHQWVKHDUDQGVXSSRUWFKDUDFWHULVWLFV
than conventional surfaces and may increase the risk of patient movement, sinking and /
RUPLJUDWLRQLQWRKD]DUGRXVSRVLWLRQVRIHQWUDSPHQWDQGRULQDGYHUWHQWEHGH[LWMonitor
patients frequently to guard against patient entrapment.
Oxygen Use – DANGER: Risk of explosion if the AtmosAir Pump is used in the presence
RIÀDPPDEOHDQHVWKHWLFV8VHRIWKLVSURGXFW¶VSXPSLQDQR[\JHQHQULFKHGHQYLURQPHQW
PD\SURGXFHSRWHQWLDORI¿UHKD]DUG7KLVHTXLSPHQWLVQRWVXLWDEOHIRUXVHLQWKHSUHVHQFH
RIDÀDPPDEOHDQHVWKHWLFPL[WXUHZLWKDLURUZLWKR[\JHQRUQLWURXVR[LGH8QSOXJDQGGR
not use pump when using oxygen-administering equipment other than the nasal mask or
half-bed-length tent type.
Shock Hazard –(OHFWULFDOVKRFNKD]DUGGRQRWUHPRYHSXPSFDVHFRYHUV5HIHUWRTXDOL¿HG
service personnel.
Transport –7RDYRLGGHÀDWLRQRIWKHPDWWUHVV6$7FHOOVHLWKHUGLVFRQQHFWDOOKRVHVIURP
PDWWUHVVDWWKHPDWWUHVVFRQQHFWRURUGLVFRQQHFWIURPWKHSXPSDQG¿WWKHWUDQVSRUWFDS
to the hose.

3
Safety Information
Patient Entrance / Exit – Caregiver should always aid patient in exiting the bed.
Make sure a capable patient knows how to get out of bed safely (and, if necessary,
KRZWRUHOHDVHWKHVLGHUDLOVLQFDVHRI¿UHRURWKHUHPHUJHQF\
Brakes – Caster brakes should always be locked once the bed is in position. Verify wheels
are locked before any patient transfer to or from the bed.
Bed Height –7RPLQLPL]HULVNRIIDOOVRULQMXU\WKHEHGVKRXOGDOZD\VEHLQWKHORZHVW
practical position when the patient is unattended.
Bed Frame – Always use a standard healthcare bed frame with this mattress, with any
safeguards or protocols that may be appropriate. Bed frame and side rails (if used) must
EHSURSHUO\VL]HGUHODWLYHWRWKHPDWWUHVVWRKHOSPLQLPL]HDQ\JDSVWKDWPLJKWHQWUDS
a patient's head or body. It is recommended that bed and side rails (if used) comply with
all applicable regulations and protocols.
CPR – Level the bed and disconnect pump (if present). Lower side rails and initiate
CPR per facility protocols. Consider use of backboard if indicated. After CPR, remove
EDFNERDUGLIXVHGUHFRQQHFWSXPSLISUHVHQWUDLVHVLGHUDLOVDQGUHFRQ¿JXUHEHGDQG
accessories as in initial placement.
Head of Bed Elevation – Keep head of bed as low as possible to help prevent patient
migration.
Side Rails / Patient Restraints - Whether and how to use side rails or restraints is
DGHFLVLRQWKDWVKRXOGEHEDVHGRQHDFKSDWLHQW¶VQHHGVDQGVKRXOGEHPDGHE\WKH
SDWLHQWDQGWKHSDWLHQW¶VIDPLO\SK\VLFLDQDQGFDUHJLYHUVZLWKIDFLOLW\SURWRFROVLQ
PLQG&DUHJLYHUVVKRXOGDVVHVVULVNVDQGEHQH¿WVRIVLGHUDLOUHVWUDLQWXVHLQFOXGLQJ
entrapment and patient falls from bed) in conjunction with individual patient needs, and
should discuss use or non-use with patient and / or family. Consider not only the clinical
and other needs of the patient but also the risks of fatal or serious injury from falling
out of bed and from patient entrapment in or around the side rails, restraints or other
accessories. Consult the local Competent Authority or Government Agency for Medical
'HYLFH6DIHW\IRUVSHFL¿FORFDOJXLGDQFH&RQVXOWDFDUHJLYHUDQGFDUHIXOO\FRQVLGHUWKH
XVHRIEROVWHUVSRVLWLRQLQJDLGVRUÀRRUSDGVHVSHFLDOO\ZLWKFRQIXVHGUHVWOHVVRUDJLWDWHG
patients. It is recommended that side rails (if used) be locked in the full upright position
when the patient is unattended. Make sure a capable patient knows how to get out of bed
VDIHO\DQGLIQHFHVVDU\KRZWRUHOHDVHWKHVLGHUDLOVLQFDVHRI¿UHRURWKHUHPHUJHQF\
Monitor patient frequently to guard against patient entrapment.
CAUTION: When selecting a standard mattress, ensure the distance
between top of side rails (if used) and top of mattress (without
compression) is at least 8.66 in (220 mm) to help prevent inadvertent
bed exit or falls. Consider individual patient size, position (relative
to the top of the side rail) and patient condition in assessing fall risk.
Skin Care – Monitor skin conditions regularly and consider adjunct or alternative therapies
for high acuity patients. Give extra attention to any possible pressure points and locations
where moisture or incontinence may occur or collect. Early intervention may be essential
to preventing skin breakdown.
I.V. and Drainage Tubes - I.V. and drainage tubes should always have slack for
alternating pressure or rotation and other patient movements.

4
Fluids –$YRLGVSLOOLQJÀXLGVRQSXPSFRQWUROV,IVSLOOVGRRFFXUFOHDQÀXLGIURPSXPS
wearing rubber gloves or while unit is unplugged to avoid any possibility of shock. Once
ÀXLGLVUHPRYHGFKHFNRSHUDWLRQRIFRPSRQHQWVLQDUHDRIVSLOO
Fluids remaining on controls can cause corrosion, which may cause
components to fail or operate erratically, possibly producing potential
hazards for patient and sta󰀨.
Avoid Fire Hazards –7RPLQLPL]HULVNRI¿UHFRQQHFWWKHEHG¶VSRZHUFRUGGLUHFWO\LQWR
a wall-mounted outlet. Do not use extension cords or multiple outlet strips. In the US,
UHYLHZDQGIROORZ)'$¶V6DIHW\7LSVIRU3UHYHQWLQJ+RVSLWDO%HG)LUHV
No Smoking in Bed –6PRNLQJLQEHGFDQEHGDQJHURXV7RDYRLGWKHULVNRI¿UH
smoking in bed should never be allowed.
Power Cord –3RVLWLRQSRZHUFRUGWRDYRLGDWULSSLQJKD]DUGDQGRUGDPDJHWRWKHFRUG
Ensure power cord is kept free from all pinch points and moving parts and is not trapped
under casters. Improper handling of the power cord can cause damage to the cord, which
FRXOGSURGXFHULVNRI¿UHRUHOHFWULFVKRFN
General Protocols – Follow all applicable safety rules and institution protocols concerning
patient and caregiver safety.
Fire Barrier Contact –&DUHVKRXOGEHWDNHQZLWKUHJDUGVWRWKH¿UHEDUULHUZKHQWKH
cover is removed. It is recommended that Personal Protective Equipment (PPE) be used
GXULQJKDQGOLQJRIWKHPDWWUHVVZLWKWKH¿UHEDUULHUH[SRVHGWRDYRLGFRQWDFWZLWKORRVH
SDUWLFOHV7RHQVXUHRSWLPDOSURGXFWSHUIRUPDQFHDYRLGRYHUKDQGOLQJRIWKH¿UHEDUULHU
DQGKDQGOHZLWKFDUH,IWKH¿UHEDUULHUEHFRPHVGDPDJHGRUVRLOHGLWVKRXOGEHUHSODFHG
End of Life Disposal –
• Fabric material used on the mattresses or any other textiles, polymers or plastic
materials etc. should be sorted as combustible waste.
• Mattresses at the end of life should be disposed of as waste according to the national
RUORFDOUHTXLUHPHQWVZKLFKPD\EHODQG¿OORUFRPEXVWLRQ
• Pump units have electrical and electronic components should be disassembled and
recycled per Waste of Electrical and Electronic Equipment (WEEE) or in accordance
with local or national regulation.
Serious Incident
If a serious incident occurs in relation to this medical device, a󰀨ecting the user, or
the patient then the user or patient should report the serious incident to the medical
device manufacturer or the distributor. In the European Union, the user should also
report the serious incident to the Competent Authority in the member state where
they are located.

5
Preparation for Use
For information concerning the bed frame, refer to the manufacturers'
User Guide.
1. Open shipping container(s).
Do not use sharp instruments to open boxes. Damage to mattress
could result.
2. Remove AtmosAir 9000A MRS from plastic protective cover.
The mattress cover may appear wrinkled when unpacked. To remove
wrinkles, allow mattress up to 24 hours to accommodate; see
Troubleshooting for more information. Wrinkles will not a󰀨ect ination
or function, so mattress may be used immediately if needed.
3. &KHFNPDWWUHVVVXUIDFHIRUWHDUVRUFUDFNLQJGRQRWXVHLIWHDUVRUFUDFNVDUH
present.
4. If re-installing mattress onto a new frame or for a new patient, check mattress
VXUIDFHIRUVWDLQLQJDQGVRLOLQJFOHDQDQGRUGLVLQIHFWDVUHTXLUHGVHHCare and
Cleaning).
5. Level bed and lock brakes.
6. Remove existing mattress from bed frame.
Mattress Installation
AtmosAir 9000A MRS
1. Position mattress on bed frame with logo facing up and product information tags
at foot end of bed.
2. Ensure there are no gaps between mattress and bed frame or side rails.
Always use a standard healthcare bed frame with safeguards or
protocols that may be appropriate. Frame and side rails must be
properly sized relative to the mattress to help minimize any gaps that
might entrap a patient’s head or body.

6
AtmosAir Pump Installation
Pump installation
1. Place pump on a solid stationary surface or suspend on end of bed frame with
built-in hanger.
2. Attach pump hoses to mattress, as shown with (Figure 1) below:
• Attach hoses to the mattress connectors on the patient left side of
the mattress for alternating p ressure.
• Ensure pump hoses are attached to pump.
3. Ensure air hoses are not kinked and will not be pinched by any articulated bed
mechanisms.
4. Attach hose connector to the pump.
5. Plug pump unit into a properly-grounded wall outlet.
6. Verify power to this outlet is not controlled by a wall switch.
7. Switch pump on.
Figure 1 Mattress Hose Connector
LED Indicators
1. Green LED is lit when the pressure is at the set level.
2. Yellow LED is lit when the pressure is below the set level. Check connections.
Pump Hoses
Mattress
Connectors
Tag
AtmosAir
MIN.
POWER
LOW PRESSURE
NORMAL PRESSURE
OFF
ON
MAX.
ALT. PRESSURE / ROTATION
Figure 2 Control Panel

7
Patient Placement and Nursing Care
It is recommended that all sections of this User Guide be read prior to product use.
Carefully review the Contraindications, Safety Information and Risks and Precautions
sections prior to placing a patient on the AtmosAir 9000A MRS.
1. Transfer patient following all applicable safety rules and institution protocols.
2. Center patient side-to-side and head-to-foot on AtmosAir MRS surface.
3. Ensure all sections of the mattress fully support the patient.
Mattress handles are for mattress transport only.
Alternating Pressure
The AtmosAir with SAT 9000A, model provides alternating pressure. The level of
DOWHUQDWLQJSUHVVXUHFDQEHDGMXVWHGIRUSDWLHQWFRPIRUW)RUPD[LPXPHႇHFWLWLV
recommended to begin at maximum intensity and adjust as needed.
Prior to engaging alternating pressure, ensure that bed frame has side
rails and that all side rails are fully engaged in full upright and locked
position. Observe patient during initial turning cycles to ensure proper
patient placement
Ensure pump hoses are properly connected to the mattress (see
AtmosAir Pump Installation).
• Rotate the control knob on the pump
clockwise to increase the intensity of
alternating pressure.
• Rotate the control knob on the pump
counter-clockwise to reduce the intensity of
alternating pressure.
The AtmosAir MRS DOES NOT provide a Nurse Hold function.
MIN.
MAX.
ALT. PRESSURE / ROTATION
Figure 3 Control Knob

8
CPR
1. Level bed.
2. Disconnect hoses from pump to level mattress,
as shown at right (Figure 4).
3. /RZHURUUHPRYHVLGHUDLORQFDUHJLYHU¶VVLGH
if necessary.
4. Begin CPR as per facility protocol. Consider use
of backboard if indicated.
5. After CPR is performed:
• Remove backboard if used.
• Reconnect pump hoses to mattress.
• Raise or install side rail as necessary.
• 5HFRQ¿JXUHEHGDQGDFFHVVRULHVDVLQLQLWLDO
placement.
Transport Mode
When disconnected from the pump, the AtmosAir 9000A MRS will operate as a reactive
surface with the full operation of the SAT system. For transport, there are two options:
1. 'LVFRQQHFWWKHWXEHDVVHPEO\IURPWKHPDWWUHVV9DOYHVZLOOFORVHRႇDVVRRQ
as the tube assembly is disconnected.
2. Disconnect the tube assembly from the pump and securely place the transport
cap on the tube assembly to maintain a seal.
Skin Care
• Remove excess moisture and keep skin dry and clean.
• &KHFNSDWLHQW¶VVNLQUHJXODUO\SDUWLFXODUO\LQDUHDVZKHUHLQFRQWLQHQFHDQG
drainage occur.
• Ensure linens under patient are not wrinkled.
Incontinence / Drainage
• Use moisture-impermeable underpads for incontinent patients.
• Wipe surface clean and replace bed linens as required (see Care and Cleaning).
General Operation
Avoid contact of sharp instruments with the AtmosAir
MRS. Punctures, cuts and tears may prevent proper
LQÀDWLRQDQGDLUSUHVVXUHPDLQWHQDQFH
Figure 4 Disconnect Hoses
Figure 5 Avoid Sharp Instruments

9
Care and Cleaning
The following processes are recommended, but should be adapted to comply with local
institution protocols. If you are uncertain, you should seek advice from your local Infection
Control Specialist.
The AtmosAir MRS should be routinely decontaminated between patients and at regular
intervals while in use.
If a powered AtmosAir MRS, ensure power cord is unplugged from wall
outlet before performing care and cleaning.
Do not use Phenol-based solutions or abrasive compounds or pads
on the cover during decontamination process as these will damage
the surface coating. Do not boil or autoclave the cover.
:LSHGRZQWKHFRYHULPPHGLDWHO\DIWHULWKDVEHHQH[SRVHGWRÀXLGV
or spills.
Fire Barrier
&DUHVKRXOGEHWDNHQZLWKUHJDUGVWRWKH¿UHEDUULHUZKHQWKHFRYHULVUHPRYHG,WLV
recommended that Personal Protective Equipment (PPE) be used during handling of
WKHPDWWUHVVZLWKWKH¿UHEDUULHUH[SRVHGWRDYRLGFRQWDFWZLWKORRVHSDUWLFOHV7RHQVXUH
RSWLPDOSURGXFWSHUIRUPDQFHDYRLGRYHUKDQGOLQJRIWKH¿UHEDUULHUDQGKDQGOHZLWKFDUH
Fire barrier should be replaced if soiled or damaged.
Cover Cleaning
Sewn AtmosAir MRS (Top cover can not be removed from base)
1. If a powered MRS, unplug pump before cleaning.
2. Remove or push bed linens to center of mattress.
The sewn AtmosAir MRS cover is cleaned by wipe down methods only.
Do not launder as damage to the base may occur.
3. Wipe and rinse any soiling from the mattress surface and base. Use 1000 ppm
chlorine or 70% alcohol.
4. Rinse with a wet towel to remove chemicals.
5. After wipe down, dry surface with towel.
6. (QVXUHEHGOLQHQVDUHUH¿WWHGDQGQRWZULQNOHGXQGHUSDWLHQW
7. Clean pump and tubes (if needed) by wiping with a damp cloth.

10
RF Welded AtmosAir MRS (Detachable top cover)
1. If a powered MRS, unplug pump before cleaning.
2. Push bed linens to center of mattress to wipe down. Remove to launder top cover
or wipe down as described below.
The RF Welded AtmosAir MRS has a detachable top cover that can be
laundered. However the base is cleaned by wipe down methods only.
'RQRWODXQGHUEDVHRU¿UHEDUULHUDVGDPDJHPD\RFFXU
3. Wipe and rinse any soiling from the mattress surface and base. Use 1000 ppm
chlorine or 70% alcohol.
4. Rinse with a wet towel to remove chemicals.
5. After wipe down, dry surface with towel.
6. (QVXUHEHGOLQHQVDUHUH¿WWHGDQGQRWZULQNOHGXQGHUSDWLHQW
7. Clean pump and tubes (if needed) by wiping with a damp cloth.
Laundering Detachable Top Cover
1. 8Q]LSWKHWRSFRYHUIURPWKHEDVHIRUODXQGHULQJ'RQRWODXQGHUEDVHDVGDPDJH
may occur.
2. Recommended wash temperature for top cover is 60° C (140° F) for 15 minutes.
3. Maximum wash temperature is 95° C (203° F) for 15 minutes.
4. Tumble dry at 60° C (140° F) or air dry.
5. Maximum drying temperature 80° C (176° F).
Cleaning AtmosAir Pump and Tubes
1. Ensure pump is unplugged.
2. Wipe surface of pump and tubes with coarse cloth using an approved disinfectant
JHUPLFLGHPL[HGWRPDQXIDFWXUHU¶VLQVWUXFWLRQVDo not ood any part of the
pump with cleaning solution.
$YRLGVSLOOLQJÀXLGVRQSXPSFRQWUROV,IVSLOOVGRRFFXUFOHDQÀXLG
from pump wearing rubber gloves or while unit is unplugged to avoid
DQ\SRVVLELOLW\RIVKRFN2QFHÀXLGLVUHPRYHGFKHFNRSHUDWLRQRI
components in area of spill. Fluids remaining on controls can cause
corrosion, which may cause components to fail or operate erratically,
SRVVLEO\SURGXFLQJSRWHQWLDOKD]DUGVIRUSDWLHQWDQGVWD௺
3. :LSHRႇH[FHVVVROXWLRQ
4. Disinfect pump and tubes with a chlorine solution (mixed according to
the instructions in the Care and Cleaning section). Using a clean cloth,
wring out excess solution until cloth is damp. Wipe pump surface and tubes
with damp cloth.
5. Allow to air dry.

11
Preventive Maintenance Schedule
Preventive maintenance for the AtmosAir MRS consists of regular cleaning (see Care and
Cleaning) and an overall system check-out to be performed at the intervals described below.
All components must be cleaned, disinfected and inspected after each patient’s use and
before use by a new patient. Always use standard precautions, treating all used equipment
as contaminated. Institutions should follow local protocols for cleaning and disinfection.
Daily Cleaning
The cover should be wiped daily with a mild soap and water solution. After wipe down,
dry surface with a towel.
Weekly Cleaning
The pump and hoses should be cleaned weekly.
Inspection / System Checks
Check each of the following before placing the AtmosAir MRS with a new patient:
1. &KHFNPDWWUHVVVXUIDFHIRUWHDUVRUFUDFNLQJGRQRWXVHLIWHDUVRUFUDFNV
are present.
2. Ensure mattress is free of stains and is not overly faded.
3. Ensure air inlet hoses and connectors on mattress and pump are clean
and undamaged.
4. Ensure pump and power cord are clean and undamaged.
5. Ensure pump hanger brackets are secure and operate correctly.
6. Ensure power switch and comfort control knob operate correctly.
7. Attach pump to the hoses and power on to ensure there are no air leaks.

12
Troubleshooting
Do not attempt troubleshooting outside this guide or where the solution recommends to
FRQWDFW$UMR$Q\XQDXWKRUL]HGVHUYLFHPRGL¿FDWLRQDOWHUDWLRQRUPLVXVHPD\OHDGWR
serious injury and / or product damage and will void all applicable warranties.
SYMPTOM POSSIBLE CAUSE SOLUTION
Green lamp on pump does not
light when power switch is set to
the ON position.
Power cord may be unplugged. Plug in power cord.
Wall outlet may be controlled by
a wall switch.
3OXJSRZHUFRUGLQWRGLႇHUHQWZDOORXWOHW
Circuit breaker for wall switch may
be tripped or blown.
Reset circuit breaker or replace fuse.
Power cord or power switch may be
damaged.
Contact Arjo for assistance.
0DWWUHVVWRR¿UPXSRQDUULYDO 'LႇHUHQFHLQDOWLWXGHQRWVXႈFLHQW
to open valves.
Apply weight to mattress to open valves.
Mattress cover too wrinkled upon
removal from shipping container.
Internal components have not
accommodated to environment. This
GRHVQRWDႇHFWLQÀDWLRQRUIXQFWLRQ
Let mattress accommodate for 24 hours.
If problem continues, contact Arjo for
assistance.
0DWWUHVVLVQRW¿UP
In use.
Tubing not connected properly. Check tubing inside mattress for loose
connectors.
Tubing kinked. Check tubing inside mattress for possible
kinks.
Tubing disconnected. Check tubing inside mattress for possible
disconnect.
Holes in or damaged to SAT system. Check SAT system for holes or damage,
or contact Arjo for assistance.
3XPSVZLWFKHGRႇ Switch pump on.
Pump leak low pressure indicator
active.
Remove and replace pump.
0DWWUHVVGHÀDWHVGXULQJWUDQVSRUW Hoses not disconnected at mattress. Disconnect hoses at mattress or
reconnect pump.
+RVHFRYHUQRW¿WWHG Connect hose cap or reconnect pump.

13
Parts Diagram - AtmosAir with SAT 9000A
All hoses were removed to improve diagram readability.
7KH¿UHEDUULHUVWDQGDUGRQDOOPDWWUHVVHVLVDVOHHYHWKDW¿WVRYHUWKHIRDPDQGSAT
assemblies.
The SAT Cover, SAT Cells, SAT Interliner and rotation bladders are all
part of the integrated SAT System and cannot be ordered separately.
See Replacement Parts for a complete list of SAT Systems.
Foam
SAT Cover
(part of SAT system)
SAT Interliner
(part of SAT system)
(image for reference only)
SAT Cell
(part of SAT system)
Fire Barrier (standard)
Welded Mattress
Separate Cover
Separate Base
Detachable Top Cover
Sewn Mattress
Cover and Base
Cover not detachable
OR

14
Parts Diagram - AtmosAir Pump 9000A
See Replacement Parts for a complete list of parts that may be
ordered for the AtmosAir Pump, as well as entire pump systems.

15
Replacement Parts
Do not attempt troubleshooting, maintenance or parts replacement outside this manual
RUZKHUHWKHVROXWLRQUHFRPPHQGVFRQWDFWLQJ$UMR$Q\XQDXWKRUL]HGVHUYLFHPRGL¿FDWLRQ
alteration or misuse may lead to serious injury and / or product damage and will void all
applicable warranties.
Replaceable AtmosAir components are listed below. For more information such as pricing,
additional options, or spare parts that are not on this list, please contact your local Arjo
representative. Contact Arjo for additional assistance.
ATMOSAIR MATTRESS COMPONENTS
AtmosAir Foam Shells
PART TYPE ....................................................................................... CATALOG NUMBER
9000 Foam Shell ........................................................................................ KA4/9FS(SIZE)
AtmosAir with SAT System
PART TYPE ....................................................................................... CATALOG NUMBER
9000A SAT System .............................................................................................. KA9ASAT
AtmosAir Fire Barrier Lining
PART TYPE ....................................................................................... CATALOG NUMBER
AtmosAir Fire Barrier Lining (standard on all sewn models) ...........................KA4/9-FBL
Welded AtmosAir Fire Barrier Lining (Standard on all AtmosAir
Welded mattresses (all models) .................................................................AtmosAir-FBL
ATMOSAIR MATTRESS COVERS
AtmosAir Model 9000A Mattress with Alternating Pressure
PART TYPE ........................................................................................................... CATALOG NUMBER
Complete Cover, Reliant IS2, Welded Top,
Non-Skid PU Bottom, No Handles.............................................. AXCRFPN(WWWLL)TXS
Complete Cover, Reliant IS2, Welded Top,
Non-Skid PU Bottom, With Handles ........................................... AXCRFPU(WWWLL)TXS
Top Cover, Reliant IS2,Welded ....................................................AXCRFXX(WWWLL)TXS
Base Cover, PU Non-skid Bottom, No Handles.......................... AXCXXPN(WWWLL)XXS
Base Cover, PU Non-skid Bottom, With Handles ....................... AXCXXPU(WWWLL)XXS
Complete Cover, Reliant IS2 Top, Non-Skid Bottom ....................AXCRLNB(WWWLL)TXS
Complete Cover, Reliant IS2 Top, Vinyl Gray Bottom ..................AXCRLVG(WWWLL)TXS
Complete Cover, Soflux Top, Non-Skid Bottom, No Handles .... AXCSONH(WWWLL)NXS
Complete Cover, Soflux Top, Non-Skid Bottom, With Handles ..AXCSONB(WWWLL)NXS
Complete Cover, Reliant IS2, RF Welded Top,
Non-Skid PU Bottom, No Handles.............................................. AXCRFPN(WWWLL)TXS
Complete Cover, Reliant IS2, RF Welded Top,
Non-Skid PU Bottom, With Handles ........................................... AXCRFPU(WWWLL)TXS
Complete Cover, Premium RF Welded Top,
Non-Skid PU Bottom, No Handles..............................................AXCPRPN(WWWLL)NXS
Complete Cover, Premium RF Welded Top,
Non-Skid PU Bottom, with Handles ............................................AXCPRPU(WWWLL)NXS
Top Cover, Reliant IS2, RF Welded .............................................AXCRFXX(WWWLL)TXS
Top Cover, Premium RF Welded ................................................ AXCPRXX(WWWLL)NXS
Base Cover, PU Non-Skid Bottom, No Handles ......................... AXCXXPN(WWWLL)XXS
Base Cover, PU Non-Skid Bottom, With Handles ...................... AXCXXPU(WWWLL)XXS

16
ATMOSAIR PUMPS
AtmosAir Standard Pumps
PART TYPE ....................................................................................... CATALOG NUMBER
AtmosAir 9000A Pump only
Europe ........................................................................................................KAPUMP-EU
UK ............................................................................................................KA9PUMP-UK
AtmosAir Harness / Tubing / Connectors (no pump) ............................ KA9PUMPASMBLY
AtmosAir 9000A Pump Filter ................................................................KA9EZPMPFILTER
AtmosAir 9000A Pump Filter Cap .........................................................KA9EZPMPFILCAP
ATMOSAIR LITERATURE
PART TYPE ....................................................................................... CATALOG NUMBER
AtmosAir 9000A MRS User Guide........................................................................ 416412
Specications
6SHFL¿FDWLRQVVXEMHFWWRFKDQJHZLWKRXWQRWLFH.
Mattresses
Maximum Recommended Patient Weight* ............................................. 500 lb (227 kg)
Weight (based on 35 in x 80 in x 7 in MRS, other sizes will vary)
AtmosAir with SAT 9000A MRS ....................................................................... 40 lb (18 kg)
Dimensions (varies depending on model)**
Minimum Length ........................................................................................ 75 in (190.5 cm)
Maximum Length .......................................................................................... 84 in (213 cm)
Minimum Width ............................................................................................ 32 in (81.5 cm)
Maximum Width ......................................................................................... 42 in (106.7 cm)
Height ............................................................................................................ 7 in (17.5 cm)
Pump 230V
Weight .............................................................................................................. 5 lb (2.5 kg)
Dimensions ..........................10.25 in (26 cm) L x 4.5 in (11.5 cm) W x 3.75 in (9.5 cm) H
Electrical:
Volts ....................................................................................................................... 230 VAC
Frequency...................................................................................................................+]
Amps ....................................................................................................................... 1 Amps
Power Cord................................................................................................................... 12 ft
Output ......................................................................................................6 litres per minute
Cycle Time ..........................................................................................................12 minutes
* Patient weight capacity may vary depending on frame use. Please consult frame manufacturer.
$GGLWLRQDOVL]HVDUHDYDLODEOH&RQWDFW$UMRIRUPRUHLQIRUPDWLRQ$WPRV$LU$6HULHVXSWRLQFP
with Reliant IS2 cover and AtmosAir 9000A with Premium cover.