Arjo Maxi 500 User manual

2Pull each leg strap under the thigh so that
it emerges on the inside of the thigh.
Place the sling flat against the patients leg
and not twisted or bunched up.
Approach the patient with the lift.
Place the spreader bar in sitting
position.
Place the spreader bar at or just below
shoulder level.
Place the spreader bar close enough to
be able to attach the shoulder straps.
1Place the sling around the patient so that
the base of the sling sits slightly below the
tail bone.
For sling with head support extend to top of
patient’s head.
Connect the sling loops or clips to the
spreader bar. Attach shoulder straps then
leg straps.
For the DPS spreader bar and clip sling,
tilt the spreader bar to attach the leg clips.
Raise the patient, position patient in a
semi-reclined position for the transfer.
Proceed with the transfer.
Lower onto new location. When body
weight is fully supported detach loops or
clips.
4
Attach and secure the clip at the lug
before patient is lifted.
3
Place attachment loop on the
hook.
Make sure the safety latches
are closed and the sling strap is
completely inside the hook.
Clip sling Loop sling
001-01389-EN Rev 0 • 06/2020 • Page 1/3
QUICK REFERENCE GUIDE - USE
Maxi 500
Lift from seated position

2Roll the patient back onto the sling and
then roll the patient in the opposite
direction, so that the folded part of the
sling can be straightened out.
Approach the patient with the lift.
Place the spreader bar in reclined
position.
Place the spreader bar close enough to
be able to attach the shoulder straps.
1Roll the patient onto their side. Fold the
sling in half and place it on the bed along
the back of the patient.
For sling with head support extend to top of
patient’s head.
Attach the sling loops or clips to the
spreader bar. Attach shoulder straps then
leg straps.
Raise the patient in a semi-reclined
position for the transfer. Proceed with the
transfer.
Lower onto new location. When body
weight is fully supported detach loops or
clips.
4
Attach and secure the clip at the lug
before patient is lifted.
3
Place attachment loop on the
hook.
Make sure the safety latches
are closed and the sling strap is
completely inside the hook.
Clip sling Loop sling
001-01389-EN Rev 0 • 06/2020 • Page 2/3
Lift from bed

ArjoHuntleigh AB
Hans Michelsensgatan 10
211 20 Malmö, Sweden
www.arjo.com 001-01389-EN Rev 0 • 06/2020 • Page 3/3
2Roll the patient back onto the sling and
then roll the patient in the opposite
direction, so that the folded part of the
sling can be straightened out.
Approach the patient with the lift, with the
open part of the chassis.
Place the spreader bar close enough to
be able to attach the shoulder straps.
1Roll the patient onto their side. Fold the
sling in half and place it on the floor along
the back of the patient.
For sling with head support extend to top of
patient’s head.
Attach the sling loops or clips to the
spreader bar. Attach shoulder straps, with
the open part of the sling, support frame
pointing downwards towards the
shoulders, connect the leg strap clips or
loops.
Raise the patient in a semi-reclined posi-
tion for the transfer. Proceed with the
transfer.
Lower onto new location. When body
weight is fully supported detach loops or
clips.
4
Attach and secure the clip at the lug
before patient is lifted.
3
Place attachment loop on the
hook.
Make sure the safety latches
are closed and the sling strap is
completely inside the hook.
Clip sling Loop sling
2
1
4
3
Lift from floorLift from