Arkon AP013 User manual

!Safety Precautions
Follow all manufacturer safety guidelines for operating your device.
Failure to practice safe usage of GPS device while driving may result
in damage, injury, or death.
Arkon is not responsible for any damages caused to your car, your
device, or yourself due to the installation or use of this pedestal mount.
www.arkon.com
Arcadia, CA 91006 USA
Designed in USA | Made in China
© Copyright 2010 Arkon Resources, Inc.
Consumer Hotline:
USA [phone]
INT’L [phone]
Monday - Friday 9 am - 5 pm, PST
The Mobile Mounting Specialists™
®
TT110 |Windshield, Dashboard & Vent Mount for TomTom GPS
Package Contents:
(1) GN014-SBH Travelmount® Mini windshield suction pedestal
(1) GN047-SBH - Removable air vent mount with dual-T swivel ball head
(1) AP013 Self-adhesive dash or console pedestal mounting disc
(1) APTTSE - TomTom dual-T adapter plate
(1) Alcohol cleaning pad
(1) APTTO - Adapter plate for TomTom ONE™ Series
(1) APTTOXL - Adapter plate for TomTom ONE XL / XL • S™ Series
(1) APTTGO520 - Adapter plate for TomTom GO™ Series
(1) APTTEP - Adapter plate for TomTom EasyPort™ Series
(1) APTTSE - Adapter plate for TomTom Start™ and Ease™
GN047-SBH
Air Vent Mounting with pedestal
Do not place mount in or near an air bag deployment zone
or where it will obstruct view of the road.
!
Installation Instructions
Continued on next page...
AP013 Disc
( 80 mm)
GN014-SBH
Windshield Or Dashboard
Mounting with Swivel Ball
Head Assembly
Windshield Mounting
Step 1.
Step 2.
Find a safe location on the interior of the vehicle’s windshield
to mount the pedestal. Firmly push the suction base (A)
against the windshield and flip the base lever down (B) to the
locked position. See diagram below.
Adjust the angle of the pedestal arm by tightening the angle
adjustment knob (C) at the base to the desired angle.
AB
C
Choose a suitable location for disc (and pedestal) installation.
Do not place mount in or near an air bag deployment zone
or where it will obstruct view of the road or hinder vehicle
operation.
Clean the dashboard or console surface area thoroughly with
the included alcohol pad. Allow the area dry before applying
the mounting disc.
Remove the paper backing of the disc and place on the
cleaned surface. Press the top of the disc down firmly to allow
the adhesive to stick to the surface. Allow 24 hours for the
adhesive to cure to the surface before applying any pressure.
Step 1.
Step 2.
Step 3.
Dashboard or Console Mounting Instructions
Place the suction cup of the pedestal firmly down on the center
of the mounting disc and lower the securing lever.
Step 4.
TomTom, ONE, GO, and EasyPort, Start and Ease are product names, trademarks, or
registered trademarks of TomTom International b.v. Arkon Resources, Inc. is not affiliated
with TomTom International b.v.
Push the pedestal suction cup (A) down onto the disk (D). Flip the
lever (B) down to secure the suction cup. Adjust the angle of the
arm by loosening the adjustment knob (C).
Step 6.
c
A
B
D
Attach the vent mounting clips (A) to the back of the pedestal
(B) with the vent clips positioned with the flat sides facing up.
Step 1.
Air Vent Mount Assembly
A
A
B
B
APTTO
Adapter plate for TomTom ONE
APTTOXL
Adapter plate for
TomTom ONE XL
and XL • S
APTTGO520
Adapter plate for
TomTom GO x20, x30
Check Compatibility
Check Compatibility
Check Compatibility
APTTEP
Adapter Plate for
TomTom EasyPort™
APTTSE
Adapter Plate for
TomTom Start™ & Ease™
TomTom Device Compatibility:
TomTom ONE 125 125-SE (TomTom EasyPort Mount)
TomTom ONE 130, ONE 130-S (TomTom EasyPort Mount)
TomTom ONE 140, ONE 140-S (TomTom EasyPort Mount)
TomTom XL 325, XL 325-S, XL 325-SE (TomTom EasyPort Mount)
TomTom XL 330, XL 330-S (TomTom EasyPort Mount)
TomTom XL 335 Series (TomTom EasyPort Mount)
TomTom XL 340, XL 340-S, XL 340 LIVE Series (TomTom EasyPort Mount)
TomTom XL 350 Series (TomTom EasyPort Mount)
TomTom XXL 530-S, XXL 535-T, XXL 540-S/WTE, XXL 550 Series (TomTom EasyPort Mount)
TomTom ONE (US Edition, US 3rd Edition)
TomTom ONE XL (1st Edition) - TomTom ONE XL-S (1st Edition)
TomTom ONE 22, ONE 22 Regional, ONE 22 Regional Traffic
TomTom XL 22, XL 22 Regional (TomTom EasyPort Mount)
TomTom ONE UK / EUROPE (NEW Edition aka 2nd Edition, 3rd Edition)
TomTom GO 520 / 530 / 630 / 720 / 730 / 920 / 920T / 930
TomTom Start and Ease

!Safety Precautions
Follow all manufacturer safety guidelines for operating your device.
Failure to practice safe usage of GPS device while driving may result
in damage, injury, or death.
Arkon is not responsible for any damages caused to your car, your
device, or yourself due to the installation or use of this pedestal mount.
www.arkon.com
Arcadia, CA 91006 USA
Designed in USA | Made in China
© Copyright 2010 Arkon Resources, Inc.
Consumer Hotline:
USA [phone]
INT’L [phone]
Monday - Friday 9 am - 5 pm, PST
The Mobile Mounting Specialists™
®
Continued on next column...
G
F
Pinch the vent mounting clips (G) so that the teeth open
and gently insert vent pedestal into vent louvres until the
mounting clips are attached to the fin/blade of the vent.
Adjust the support leg (H) vertically until it rests firmly along
the bottom of the vent or dash surface below the vent.
Step 4.
Insertion of Mount Assembly into Air Vent
Attach your cradle or device (not included, sold
separately) to the dual-T head by inserting the dual-T
tabs (E) into the dual-T slots (F) on the back of the cradle
or device.
Step 3.
Attach Device or Cradle to Air Vent Mount
G
H
TT110 |Windshield, Dashboard & Vent Mount for TomTom GPS
Step 1. While holding the mounted adapter plate, gently insert the
device (not included, sold separately) into the adapter plate
until an audible click is heard. The device can then be rotated
into the desired viewing angle.
TomTom EasyPort Device Insertion
Connect the dual T-slots (I) on adapter plate to the dual T-tabs
(J) on the pedestal head. Adjust the angle of the head by
tightening the head adjustment knob (K).
Step 1.
TomTom EasyPort Adapter Plate Installation
I
J
K
TomTom Device Installation - Pedestal Attachment
Attach the device holder to the pedestal by inserting the
dual T-Tabs of the pedestal into the T-slots of the TomTom
adapter plate. Readjust angle knob if necessary.
Step 1.
Angle Knob
Angle Knob
TomTom GO Adapter Plate Installation
Step 1. Attach the adapter plate by sliding it up into the slot
on the back of the TomTom GO 520, 530, 630, 720, 730,
920, 920T or 930 device as shown. Attach the device
as shown below.
Slide the adapter plate up into the grooves on the back of the
TomTom ONE, ONE XL, or ONE XL•S device.
TomTom ONE, ONE XL, and ONE XL • S Plate Installation
Step 1.