Arkon SLIM-GRIP IPM515 User manual

SM427
|Bicycle Handlebar Mount with Universal Holder
The Mobile Mounting Specialists™
®
Consumer Hotline:
USA [phone]
INT’L [phone]
Monday - Friday 9 am - 5 pm, PST
www.arkon.com
Arcadia, CA 91006 USA
Designed in USA | Made in China
© Copyright 2010 Arkon Resources, Inc.
Package Contents:
(1) SM050-HPB-2 - Slim-Grip™ holder for Apple iPhone and iPod touch®
(1) GN015-HPB-2 - Mini Windshield Suction and Dashboard Mount
(1) AP013 - Circular Adhesive Dashboard Disc
AP013
Circular Adhesive
Dashboard Disk
GN015-HPB-2
Mini Windshield
Suction Pedestal
IPM515
|Slim-Grip™ with Mini Windshield Suction and Dashboard Mount for Apple iPhone® and iPod touch®
82 mm
expandable to
118.5 mm
Connect the dual T-slots (A) on holder to the dual T-tabs (B) on
the pedestal head.
A
A
A
A
B
B
B
A
Optional Cord
Catcher
Secure holder with your hand for support, as spring-loaded
mechanism requires significant force to operate. Hold your phone
and insert into universal holder by pushing down on the bottom
spring-loaded support legs with moderate amount of pressure
(C). Slide the top of the device under the top support legs (D) until
it fits snuggly in the holder.
Insert Phone into Holder
D
C
Connecting the Slim-Grip™ Holder to Dual T-Tab PedestalWindshield Mounting
Install the Support Legs to the Holder
Step 1.
Step 1.
Step 1.
Step 1.
Find a safe location on the interior of the vehicle’s windshield
to mount the pedestal. Firmly push the suction base (A)
against the windshield and flip the base lever down (B) to the
locked position. See diagram below.
Insert the holder support legs (A) by sliding them into the
support leg grooves (B) on the top and bottom of the holder.
AB
Continued on other side...
!Safety Precautions
Do not install Arkon products over an air bag cover or within the air
bag deployment zone. Arkon Resources, Inc. assumes no responsi-
bility of liability for injury or death as a result of car crashes and/ or
air bag deployment.
Arkon is not responsible for any damages caused to your car, your
device, or yourself due to the installation or use of this pedestal mount.
Compatible with the following devices:
Apple iPhone® 4•
Apple iPhone® 3GS•
Apple iPhone® 3G•
Apple iPhone® Original•
Apple iPod touch® - All models•
*Apple®, iPhone®, and iPod touch®are trademarks of Apple Computer, Inc.
Arkon Resources, Inc. is not affiliated with Apple Computer, Inc.
SM050-2-HPB
Slim-Grip™ Holder
for iPhone & iPod touch

The Mobile Mounting Specialists™
®
Consumer Hotline:
USA [phone]
INT’L [phone]
Monday - Friday 9 am - 5 pm, PST
www.arkon.com
Arcadia, CA 91006 USA
Designed in USA | Made in China
© Copyright 2010 Arkon Resources, Inc.
IPM515
|Slim-Grip™ with Mini Windshield Suction and Dashboard Mount for Apple iPhone® and iPod touch®
Choose a suitable location for disc (and pedestal) installation.
Do not place mount in or near an air bag deployment zone
or where it will obstruct view of the road or hinder vehicle
operation.
Clean the dashboard or console surface area thoroughly with
the included alcohol pad. Allow the area dry before applying
the mounting disc.
Remove the paper backing of the disc and place on the
cleaned surface. Press the top of the disc down firmly to allow
the adhesive to stick to the surface. Allow 24 hours for the
adhesive to cure to the surface before applying any pressure.
Step 1.
Step 2.
Step 3.
Dashboard or Console Mounting Instructions
Place the suction cup of the pedestal firmly down on the center
of the mounting disc and lower the securing lever.
Step 4.
Push the pedestal suction cup (A) down onto the disk (C). Flip the
lever (B) down to secure the suction cup. Adjust the angle of the
pedestal head as needed.
Step 5.
A
B
C
!Safety Precautions
Do not install Arkon products over an air bag cover or within the air
bag deployment zone. Arkon Resources, Inc. assumes no responsi-
bility of liability for injury or death as a result of car crashes and/ or
air bag deployment.
Arkon is not responsible for any damages caused to your car, your
device, or yourself due to the installation or use of this pedestal mount.
Adjusting Holder to Fit Phone
E
E
If necessary, adjust the support legs (E) on top and bottom by
sliding them laterally to avoid any buttons or ports that may be
on your phone.
Step 1.
Continued in
next column...