Armorgard TrekDror TKD1 User manual

User manual for your
Armorgard TrekDror
TrekDror™
Model Numbers TKD1,TKD2 & TKD3

2
Welcome...
to your Armorgard TrekDror, the safest and most
secure tool drawer range for your vehicle. The TrekDror
comes ready to use, but please consult this manual for
instructions on how to adapt it to your needs.
Please read this user manual carefully
prior to setting up the TrekDror
Please call 023 9238 0280 if you have any questions on your TrekDror.
Contents
Welcome
Safety Information
Removing and fitting the drawer
Stacking multiple TrekDrors
Mounting the TrekDror using the fixing points
Additional kits
General Information
................................................................................. page 2
.................................................................... page 3
................................................ page 4
....................................................... page 5
............................ page 5
.......................................................................... page 6
.................................................................. page 6

3
Safety Information
At least 2 people are required to safely lift any TrekDror due to the
weight.
Ensure the TrekDror is empty before removing or fitting the drawer.
If you decide to fit the TrekDror in a vehicle, consult the vehicle
manufacturer before carrying out any work to the vehicle itself.
Armorgard cannot be held responsible for any damage caused
while fitting the TrekDror unit.
Technical Specification
Product
code
External
dimensions (mm)
Internal dimensions
(mm)
Net weight
TKD1 300x1105x490 245x1040x435 45kg
TKD2 200x1105x980 150x1040x925 65kg
TKD3 490x1105x490 435x10460x435 60kg
When stacking TrekDrors, 4 brackets must be used to fully support
the units. The base unit should always be secured to a solid floor
or solid base
Use caution when removing or replacing the drawer
When used in a vehicle or trailer, the TrekDror MUST be securely
fastened down to prevent it moving in transit.

4
To remove the drawer, pull it right
out until it stops.
Loosen these bolts off, until the
drawer can slide out freely.
Locate the two bolts inside the
drawer at the rear.
The drawer can now be removed.
When it is replaced, ensure that
the bolts are tightened up again
and test to ensure the drawer
can’t slide completely out.
1.
3.
2.
4.
Removing and fitting the drawer

5
If you have more then one
TrekDror, they can be stacked in
different layouts using the optional
stacking plates. These create a
small gap between the units.
Remove the drawer and slot two
coachbolts into the fixing points at
the rear of the casing. Drop the
rear down through prepared holes
in the floor, and screw nuts onto
the coachbolt from the other side
of the surface.
Bolt the stacking plates to the
fixing points on the side of the
TrekDrors. All 4 plates and 16
bolts are required to keep it rigid
and secure.
At the front, push the bolts
through from inside the casing.
M10 bolts are recommended for
best fit. Ensure the casing is rigid
and firm before fitting the drawer
back in place.
1.
1.
2.
2.
Stacking multiple TrekDrors
Mounting the TrekDror using the fixing points

6
Lost Keys?
Replacement keys can be purchased from Armorgard, using the
serial number on the product.
Spare Parts
The following parts are available to order separately:
Additional Kits
General Information
The TrekDror can be stacked with other TrekDrors or mounted on a
base using optional kits. Please call 023 9238 0280 for more details.
- Dividers
- Outer casing
- Roller bearings
- Stacking plate kit
- Drawers
- External floor mounting kit
- Mounting plate kit

7
ticking every box
View our full range of products online at
www.armorgard.co.uk

8
Unit 14-16, Standard Way, Fareham Industrial Park, Fareham, Hampshire PO16 8XB
t: 023 9238 0280 e: [email protected] w: www.armorgard.co.uk